Behringer Clocked Sequential Control Module 1027 Manual

Behringer Synthesizer Clocked Sequential Control Module 1027

Læs gratis den danske manual til Behringer Clocked Sequential Control Module 1027 (3 sider) i kategorien Synthesizer. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Behringer Clocked Sequential Control Module 1027, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

CLOCKED SEQUENTIAL

CONTROL MODULE 1027

Legendary 2500 Series 8-Position Step

Sequencer Module for Eurorack

Controls

(1) CH A / CH B / CH C SEQUENCER COLUMNS – Use the

knobs to set the control voltage output for each step.

Each column sends out control voltages via that channel’s

respective CH A / CH B / CH C output jack.

(2) STEP LEDs – Each LED lights to indicate its respective

sequencer step is active.

(3) POSITION GATES – Each of these output jacks sends out a

gate signal for its respective sequence step via cables with

3.5 mm TS connectors. These 8 gate output signals are

also available via the 12-pin GATE OUT LINK CONNECTOR

located on the module underside. This 12-pin connector

can connect to and trigger other compatible modules,

such as the MIX-SEQUENCER MODULE 1050, via a 12-pin

ribbon connector.

(4) RATE – This knob controls the step speed at which the

sequencer moves from step to step. The knob operates

in two overall frequency ranges determined by the

LOW/HIGH switch.

(5) LOW/HIGH – Use this sliding switch to set whether the

RATE knob operates in a lower-frequency (LOW) or

higher-frequency (HIGH) range.

(6) % PULSE WIDTH – Select between width settings

for the rectangular waveform ranging from 5% to 95%

duty cycle. The PULSE WIDTH control operates on the

CLK OUT jack only, making this control very useful for

triggering other modules such as envelope generators,

and so on.

(7) INT/EXT – Use this switch to select between internal (INT)

or external (EXT) pulse width control voltage. When EXT

is selected, the % PULSE WIDTH control knob is disabled.

(8) ON /OFF – This button starts or stops the sequence with a

manual button push.

(9) STEP – Press this button to manually progress to the next

sequencer step.

(10) RESET – Press this button to manually restart the

sequence at step 1.

(11) STEP – Use this jack to route external trigger signals for

the STEP button into the module via cables with 3.5 mm

TS connectors.

(12) RESET – Use this jack to route external trigger signals for

the RESET button into the module via cables with 3.5 mm

TS connectors.

(13) ON – Use this jack to route external trigger signals to

enable the step counter into the module via cables with

3.5 mm TS connectors.

(14) OFF – Use this jack to route external trigger signals to

disable the step counter into the module via cables with

3.5 mm TS connectors.

(15) RATE – Use this jack to route in external control voltage

signals for the sequencer's step speed (usually controlled

by the RATE knob) via cables with 3.5 mm TS connectors.

(16) WIDTH – This jack allows control voltage and modulation

signals for the rectangular waveform to be routed in via

cables with 3.5 mm TS connectors.

(17) CH A – This jack sends out control voltage signals for

the CH A sequencer column via cables with 3.5 mm

TS connectors.

(18) CH B – This jack sends out control voltage signals for

the CH B sequencer column via cables with 3.5 mm

TS connectors.

(19) CH C – This jack sends out control voltage signals for

the CH C sequencer column via cables with 3.5 mm

TS connectors.

(20) CLK OUT – Use this jack to export the internally generated

clock signal via cables with 3.5 mm TS connectors.

The internal clock produces a gate pulse every time

the sequencer steps, and the gate pulse’s width can be

adjusted using the % PULSE WIDTH control or via the

WIDTH control jack.

(1) (3)(2)

(4)

(5)

(6)

(7)

(8)

(9)

(13) (14)(15)(16) (17) (20)(18) (19)(12)

(10)

(11)

V 1.0

Quick Start Guide

Power Connection

The CLOCKED SEQUENTIAL CONTROL MODULE 1027 module comes

with the required power cable for connecting to a standard

Eurorack power supply system. Follow these steps to connect

power to the module. It is easier to make these connections before

the module has been mounted into a rack case.

1. Turn the power supply or rack case power o and

disconnect the power cable.

2. Insert the 16-pin connector on the power cable into the

socket on the power supply or rack case. The connector has

a tab that will align with the gap in the socket, so it cannot

be inserted incorrectly. If the power supply does not have

a keyed socket, be sure to orient pin 1 (-12 V) with the red

stripe on the cable.

3. Insert the 10-pin connector into the socket on the back of

the module. The connector has a tab that will align with the

socket for correct orientation.

4. After both ends of the power cable have been securely

attached, you may mount the module in a case and turn on

the power supply.

Installation

The necessary screws are included with the module for mounting in

a Eurorack case. Connect the power cable before mounting.

Depending on the rack case, there may be a series of xed holes

spaced 2 HP apart along the length of the case, or a track that allows

individual threaded plates to slide along the length of the case.

The free-moving threaded plates allow precise positioning of the

module, but each plate should be positioned in the approximate

relation to the mounting holes in your module before attaching

the screws.

Hold the module against the Eurorack rails so that each of the

mounting holes are aligned with a threaded rail or threaded

plate. Attach the screws part way to start, which will allow small

adjustments to the positioning while you get them all aligned. After

the nal position has been established, tighten the screws down.

Specications

Inputs

On / o

Type 2 x 3.5 mm TS jacks,

DC coupled

Impedance 100 KΩ, unbalanced

Maximum input level 10 V

Minimum switching

threshold

2.5 V, trigger

Rate

Type 1 x 3.5 mm TS jack,

DC coupled

Impedance 100 KΩ, unbalanced

Maximum input level 10 V, 1 V/oct.

Width

Type 1 x 3.5 mm TS jack,

DC coupled

Impedance 100 KΩ, unbalanced

Maximum input level 10 V

Step / reset

Type 2 x 3.5 mm TS jacks,

DC coupled

Impedance 100 KΩ, unbalanced

Maximum input level 10 V

Minimum switching

threshold

2.5 V

Outputs

Ch A / B / C

Type 3 x 3.5 mm TS jacks,

DC coupled

Impedance 1 KΩ, unbalanced

Maximum output level 10 V

Clock out

Type 1 x 3.5 mm TS jacks,

DC coupled

Impedance 1 KΩ, unbalanced

Maximum output level 5 V

Produkt Specifikationer

Mærke:	Behringer
Kategori:	Synthesizer
Model:	Clocked Sequential Control Module 1027

Har du brug for hjælp?

Hvis du har brug for hjælp til Behringer Clocked Sequential Control Module 1027 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Synthesizer Behringer Manualer

Behringer JT MINI Manual

2 Januar 2025

Behringer WAVES Manual

2 Januar 2025

Behringer SWORDS Manual

2 Januar 2025

Behringer Bode Frequency Shifter 1630 Manual

14 December 2024

Behringer Concert CDP2400USB Manual

29 September 2024

Behringer MS-5 Manual

2 September 2024

Behringer Spring Reverberation 646 Manual

1 September 2024

Behringer CP3A-M Mixer Manual

1 September 2024

Behringer RADAR Manual

25 August 2024

Behringer PRO-VS MINI Manual

25 August 2024

Synthesizer Manualer

Nyeste Synthesizer Manualer

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

11 Januar 2025

13 December 2024