Blustream DA22XLR-WP-US Manual


Læs nedenfor 📖 manual på dansk for Blustream DA22XLR-WP-US (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
DA22XLR-WP-US QUICK REFERENCE GUIDE
03
Contact: support@blustream.com.au support@blustream-us.com | | support@blustream.co.uk
Dante® Controller so฀ware is required in order to set
up and configure the DA22XLR-WP-US as well as control
the Dante network. Audinate provide extensive training ®
videos and documentation on their website. This can
be found here: http://www.audinate.com/products/
so฀ware/dante-controller
Upon connecting the DA22XLR-WP-US to a compatible
network, the Dante Controller so฀ware will ®
automatically discover the device. The DA22XLR-WP-US
will appear in the Dante Controller with a name prefixed ®
as “DA22XLR-WP-US”. On the Routing” screen audio can
be routed between Dante transmitters and receivers in ®
the system.
Please ensure that the PC is on the same network as
the Dante devices. Dante is not able to transmit over ® ®
WiFi, and it is recommended to hardwire into the Dante®
network. Having multiple network devices enabled
can also confuse the Dante Controller so฀ware so it is ®
recommended to disable WiFi during configuration.
Dante® Controller
RevA4_QRG_DA22
Advanced Dante Settings®
It is also possible to change the settings of the DA22XLR-
WP-US within the “Device Info” screen in the Dant
Controller so฀ware. To do so, select theDevice Config
menu.
The sample rate of the DA22XLR-WP-US can be adjusted
here. Please note: Dante products can only transmit or ®
receive audio from other Dante products that are set up ®with the same sample rate. A mismatch in sample rate may stop audio from transmitting.Under the “Device Configscreen, the latency can be adjusted of the DA22XLR-WP-US from 1, 2 or 5 milliseconds.By default the DA22XLR-WP-US is shipped with its network settings set to obtain an IP address automatically. This means that if a DHCP ser ver is present on the network, it will provide the DA22XLR-WP-US with an IP address. If no DHCP server is present then the DA22XLR-WP-US will receive a default IP address in the 169.254.xxx.xxx range. To change the IP address of the DA22XLR-WP, enter the Network Config” menu in the “Device Info screen of the Dante® Controller so฀ware.


Produkt Specifikationer

Mærke: Blustream
Kategori: Ikke kategoriseret
Model: DA22XLR-WP-US

Har du brug for hjælp?

Hvis du har brug for hjælp til Blustream DA22XLR-WP-US stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Blustream Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Senal

Senal SCI-3212MP Manual

22 November 2024
Senal

Senal OLM-2S-P Manual

21 November 2024
Senal

Senal ME-220-CL Manual

21 November 2024
Senal

Senal ASM-4 Manual

21 November 2024
Senal

Senal CS-88 Manual

21 November 2024
Senal

Senal CSP-162 Manual

21 November 2024
Senal

Senal MXGN-ICS Manual

21 November 2024
Dubatti

Dubatti Board Two Manual

21 November 2024
Senal

Senal ASM-3 Manual

21 November 2024