Dell PowerConnect J-EX4200 Manual

Dell Ikke kategoriseret PowerConnect J-EX4200

Læs gratis den danske manual til Dell PowerConnect J-EX4200 (24 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Dell PowerConnect J-EX4200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

Dell PowerConnect J-Series J-EX4200 Ethernet Switch Quick Start

To install and configure a Dell PowerConnect J-Series J-EX4200 Ethernet Switch

(regulatory model numbers EX4200-24T, EX4200-24F, and EX4200-48T), you need:

zTwo mounting brackets and eight mounting screws (provided)

zPhillips (+) screwdriver number 2 to remove and tighten screws

zHardware to secure the chassis to the rack (provided)

zJumper cord and cord retainer (provided)

zGrounding cable—minimum 14 AWG (2 mm²), minimum 90°C wire—with Panduit

LCD6-14BH-L grounding lug or equivalent attached by a licensed electrician

zTwo 10-32x.25-in. screws with split washers to secure the grounding lug to the switch

zManagement host, such as a PC, with an Ethernet port

zEthernet cable (provided)

NOTE: A Virtual Chassis cable and two cable connector retainers are provided, but their

use is not covered here. These instructions are for two-post rack installation only. For

four-post rack or wall installation, Virtual Chassis configuration, and other tasks, see the

PowerConnect J-EX4200 switch documentation at http://www/support.dell.com/manuals.

NOTE: Four-post rack-mount and wall-mount kits are available separately.

Part 1: Install a Power Supply in the Switch (If It Is Not Installed)

1. Remove the power supply from the bag. Take care not to touch power supply

components, pins, leads, or solder connections.

2. Push down on the locking lever on the left front of the power supply until it is in its

lowest position (see the figure in Part 4 for the location of the locking lever). You

might need to loosen the locking lever screw to move the lever.

3. Using both hands, place the power supply in the power supply slot on the rear panel

of the switch and slide it in until it is fully seated.

4. Push the locking lever up to its highest position (this action might pull the power

supply in). Tighten the locking lever screw using the screwdriver.

Part 2: Mount the Switch

1. Place the switch on a flat, stable surface.

2. Attach the mounting brackets to the switch chassis with the eight mounting screws.

3. Make sure the rack is properly secured to the building in its permanent location.

4. Have one person grasp both sides of the switch, lift it, and position it in the rack,

aligning the bracket holes with the holes in the rack.

5. Have a second person install a rack-mount screw—and cage nut and washer if your

rack requires them—in each of the four bracket holes to secure the switch to the rack.

Part 3: Connect the Switch to Earth Ground

1. Connect one end of the grounding cable to a proper earth ground, such as the rack in

which the switch is mounted.

2. Place the grounding lug attached to the grounding cable over the protective earthing

terminal on the left side of the chassis, and secure the lug to the terminal with the

screws and washers.

Part 4: Connect AC Power to the Switch

NOTE: If you are interconnecting multiple switches as a Virtual Chassis, power on only

one switch—the one you will use as the master.

1. Squeeze the two sides of the cord retainer clip, and insert the L-shaped ends of the

wire clip into the holes in the bracket on each side of the AC appliance inlet on the

power supply faceplate.

2. Insert the coupler end of the jumper cord into the AC appliance inlet.

3. Push the cord into the slot in the adjustment nut of the cord retainer. Turn the nut until

it is tight against the base of the coupler and the slot in the nut is turned 90° from the

top of the switch.

4. If the AC power source outlet has a power switch, set it to the OFF (0) position.

5. Insert the jumper cord plug into the power source outlet.

6. Repeat these steps for each AC power supply.

7. If the AC power source outlet has a power switch, set it to the ON (|) position.

NOTE: When you connect power to the switch, the Alarm (ALM) LED lights red (major

alarm) to indicate that the network is disconnected. This behavior is normal. Plugging an

active Ethernet cable into the management (MGMT) port on the switch completes the

network link and turns the ALM LED to amber (minor alarm).

The ALM LED turns off when you create a backup rescue configuration.

G

-OUNTINGBRACKET

AC DC

Locking

lever

Tighten

adjustment nut.

Retainer clip

Adjustment nut

AC DC

g020063

Produkt Specifikationer

Mærke:	Dell
Kategori:	Ikke kategoriseret
Model:	PowerConnect J-EX4200

Har du brug for hjælp?

Hvis du har brug for hjælp til Dell PowerConnect J-EX4200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dell Manualer

Dell Pro Tower Plus QBT1250 Manual

13 November 2025

Dell Wyse Management Suite Manual

21 August 2025

Dell PowerConnect W-3600 Manual

10 August 2025

Dell PowerConnect 3548P Manual

9 August 2025

Dell PowerConnect J-SRX240 Manual

9 August 2025

Dell W-6000 Manual

9 August 2025

Dell PowerConnect 7024F Manual

9 August 2025

Dell WH125 Manual

24 Juli 2025

Dell DA310 Manual

5 Juli 2025

Dell KM3322W Manual

4 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Panasonic EY37A2 Manual

22 December 2025

Blaupunkt BP-TA1400 Manual

21 December 2025

GE GFC720N Manual

21 December 2025

GE GFC525N Manual

21 December 2025

WAC Lighting R4RNL-36EM Manual

21 December 2025

WAC Lighting LTK-738 Manual

21 December 2025

Silverstone HELA 2500Rz Manual

21 December 2025

Delta 1993LF Manual

21 December 2025

AEG MG2600B Manual

21 December 2025

Blaupunkt BP 13.0A Manual

21 December 2025