Dormakaba RCI 8371 Manual

Dormakaba Ikke kategoriseret RCI 8371

Læs gratis den danske manual til Dormakaba RCI 8371 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Dormakaba RCI 8371, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

I N S T A L L A T I O N 8371/8372

Surface MiniMag® Electromagnetic Locks

1. Mount the electromagnetic lock to the door frame as outlined

on the installation template included with the product.

NOTE: During installation of the armature plate to the door it is

essential that the armature plate remains movable. The armature

plate must be allowed to pivot on the center-mounting bolt to allow

proper alignment with the magnet surface. If the plate is not aligned

with the magnet surface, the lock may lose holding force or not

lock at all.

The head of the armature mounting bolt ships with a rubber washer

affixed to it. This washer should project slightly beyond the surface

of the armature plate. This is to allow the washer to expand when

power is removed and break the air vacuum between the plate

and the magnet surface. If this washer is removed or trimmed the

lock will appear to have some holding force even when power is

removed.

For added safety, thread locking compound has been provided for

the armature plate bolt and the four captive electromagnetic lock

mounting screws.

WARNING: Improper installation, maintenance, inspection or

usage of the product or any related accessories or parts may

cause the electromagnetic lock, armature plate and associated

hardware to disengage and fall, causing serious bodily injury

and property damage. Rutherford Controls Int’l Inc. and/or

Rutherford Controls Int’l Corp. will not be liable to the installer,

purchaser, end user or anyone else for damage or injury to person

or property due to improper installation, care, storage, handling,

maintenance, inspection, abuse, misuse or act of God or nature

involving this product or any related accessories or parts.

2. Route the power supply wire through door frame and into

magnet housing. Connecting wire should be of sufficient gauge

for the lock being installed and the distance being run. (See table

on page 6.)

WWW.RUTHERFORDCONTROLS.COM • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: SALES@RUTHERFORDCONTROLS.COM

IS8371/72 PCN15010

R10/15GR-2

In or Out... we make it Easy!®

Instructions

Pre-Installation Instructions

1. This product must be installed according to all applicable

building and life safety codes.

2. Due to the variety of mounting configurations available with

this product, a survey and assessment of the physical area

in which the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally

sound prior to installation of the electromagnetic lock. The

structural integrity of the mounting surfaces must be strong

enough to meet or exceed the holding force of the product.

4. The product must be protected from potential damage due

to intruders or tampering.

5. The product should be installed in a location that will not

hinder or create a potential safety hazard to authorized

personnel accessing the protected area.

6. Because electromagnetic locks are used in a variety of

applications and different door frame configurations, an

experienced installer with knowledge of this product must

make a determination of the optimal mounting method for

this specific application.

7. The components, hardware, installation instructions and

mounting template included with this product are intended

for use on outswinging doors.

8. Do not install this product on the exterior of buildings.

9. Do not use as a doorstop. This will void warranty.

10. Separate accessories not included with this product must

be used in the following applications:

• Inswinging doors

• Narrow head jamb situations or center-hung doors

• Wherever there is insufficient space on the door

frame header to mount the lock

• Glass or Herculite doors that do not have a door frame

• Hollow metal or wood frames where the door stop is

not thick enough to allow the product to be installed

• Wherever an obstruction in the door prevents

installation of the armature plate at a proper height

• Doors that do not permit the armature plate to be

mounted low enough to meet the magnet surface

Refer to the Product Accessories Guide section of

the Installation Instructions for further information.

Accessories may impact holding force.

11. Installation of this product should be done by an

experienced installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound

be applied to all screws during installation to reduce chance of

screws loosening over extended time.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

Produkt Specifikationer

Mærke:	Dormakaba
Kategori:	Ikke kategoriseret
Model:	RCI 8371

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba RCI 8371 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Dormakaba Manualer

Dormakaba CenTran 4 Manual

19 Oktober 2025

Dormakaba Crane S1 Manual

19 Oktober 2025

Dormakaba Auditcon T52 Manual

18 Oktober 2025

Dormakaba 12C Manual

18 Oktober 2025

Dormakaba 3513-DM Manual

29 Juni 2025

Dormakaba Keyscan EC1500 Manual

21 August 2024

Dormakaba RCI S2500A Manual

21 August 2024

Dormakaba EAC Manual

21 August 2024

Dormakaba CLM9000 Manual

21 August 2024

Dormakaba DKX Type III Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Dahua Technology EVS7124D Manual

27 Oktober 2025

Dahua Technology XVR7816S-4KL-X-LP Manual

27 Oktober 2025

Dahua Technology HAC-HDW1220EM Manual

27 Oktober 2025

Dahua Technology ISC-M6550 Manual

27 Oktober 2025

Dahua Technology EVS7148D Manual

27 Oktober 2025

Dahua Technology HAC-HFW2249E-A Manual

27 Oktober 2025

Dahua Technology XVR5108/16H-X Manual

27 Oktober 2025

Dahua Technology XVR5108HE-4KL-I2 Manual

27 Oktober 2025

Dahua Technology XVR7104HE-4KL-I Manual

26 Oktober 2025

Dahua Technology NVR4816-4KS2 Manual

26 Oktober 2025