Electro-Voice TK-150 Manual

Electro-Voice Ikke kategoriseret TK-150

Læs gratis den danske manual til Electro-Voice TK-150 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Electro-Voice TK-150, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Instructions

F.01U.301.246 Rev 03 08/2014

TK-150

150 Watt Transformer for 70.7/100 Volt Lines

Tools Required:

1. #2 Phillips screwdriver

2. 3/16 in (5 mm) at blade screwdriver

High Pass Filter Requirements:

The TK-150 is designed to be used with a 50 Hz Butterworth

24 dB/octave active high-pass lter inserted in the signal chain

at the input to the driving amplier. This lter protects the

amplier from damage caused by transformer saturation at

low frequencies and allows any number of transformers to be

driven on the same line, up to the rated power of the amplier.

The TK-150 is capable of delivering up to 300 Watts to the

loudspeaker using the following conguration. Connect a 100 V

drive line to the tap labeled, DO NOT USE (150 W at 70.7 V).

Insert a Butterworth 24 dB/octave active high-pass lter tuned

to 66 Hz or higher in the signal chain at the input to the driving

amplier. Due to the band limited spectrum of the EN54-24

simulated program signal (89 Hz - 11.2 kHz) the EN54-24 rated

power handling is certied up to 400 Watts at the100 V drive line.

Caution!

Failure to use the proper high-pass lter may result

in damage to the amplier.

Instructions:

To install the TK-150, do the following:

1. Remove the input panel by removing the eight (8) screws

securing it.

Make note of the original orientation prior to removing the

input panel.

2. Unplug the crossover wiring harness from the 7-pin header.

3. Place the input panel horizontally face down with the green

circuit board on the right.

4. Place the transformer in the pocket on the left.

The lead wires from the transformer should be pointed

toward you.

5. Secure the transformer mounting ears to the four (4)

input panel bosses with the four (4) #10 screws provided.

Carefully tighten the screws evenly in an X-cross pattern to

avoid warping the plastic input panel.

6. Unplug the 8-position jumper connector located at right

angle to the 7-pin crossover header.

Produkt Specifikationer

Mærke:	Electro-Voice
Kategori:	Ikke kategoriseret
Model:	TK-150

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro-Voice TK-150 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Electro-Voice Manualer

Electro-Voice Zx5-60PI Manual

28 September 2025

Electro-Voice Evolve 90 Manual

2 September 2025

Electro-Voice EVOLVE-WMK-PW Manual

18 Juli 2025

Electro-Voice EVOLVE-WMK-NW Manual

17 Juli 2025

Electro-Voice EVOLVE-WMK-NB Manual

17 Juli 2025

Electro-Voice EVOLVE-WMK-PB Manual

17 Juli 2025

Electro-Voice EVOLVE-TM-B Manual

17 Juli 2025

Electro-Voice EVU-CDNL4 Manual

30 Juni 2025

Electro-Voice ZLX-8-G2 Manual

26 Februar 2025

Electro-Voice MFX-12MC Manual

13 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Velux TGR 010 Manual

7 Januar 2026

LG PREMTC00U Manual

7 Januar 2026

LG PREMTBVC2 Manual

7 Januar 2026

Reelcraft WCH80001 Manual

7 Januar 2026

Panduit CT-1015 Manual

7 Januar 2026

WAC Lighting MT4LD216NE Manual

7 Januar 2026

WAC Lighting HTK-703 Manual

7 Januar 2026

Verkada AC42 Manual

7 Januar 2026

Panduit FC2ZO-24-10AF Manual

7 Januar 2026

Vaxcel T0678 Manual

7 Januar 2026