Joblotron AC-82 Manual

Joblotron Overvågningskamera AC-82

Læs gratis den danske manual til Joblotron AC-82 (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Joblotron AC-82, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

The AC-82 wireless relay output module MJT51202

The AC-82 wireless relay output module

The AC-82 is a component of Jablotron’s Oasis JA-80 system. It is

mains-powered (230V AC) and it provides 2 relays which can be

controlled by radio signals and offers the following:

• Remotely controllable relay outputs which follow JA-80 control

panel programmable PG outputs

• Remote control of appliances using RC-8x controllers

• Relay output of JA-8x wireless detectors

• Relay output of TP-8x wireless thermostats

RADIO

max F 5 A / 250V

buttons

LEDs

fuse

max 5 A

X Y

Installation

Installation of this module shall only be undertaken by technicians holding a

certificate issued by an authorized distributor..

Warning: this device is galvanically connected to the mains.

Open the module’s cover (1 screw) and take out the circuit board (2

tabs). Install the back part of the housing to the desired place, re-install

the circuit board, connect the wires and enroll the desired wireless

devices.

Terminals

L,N Power: 230V AC/50Hz

COM Common terminal for the output contacts X and Y (fused by a 5

Amp fuse)

RE1 Normally open relay X contact

RE2 Normally open relay Y contact

The enrollment of transmitters

The X and Y relays are totally independent. Jablotron Oasis devices with

transmitters can be enrolled to them individually using the X and Y enrollment

buttons. Each relay offers 4 different enrollment modes (1 to 4, see the following

table). The reaction of a relay to a transmitter signal depends on which

enrollment mode the transmitting device has been enrolled to.

Enrollment procedure

• Use the X or Y button depending on which relay you want to enroll a device

to.

• Repeatedly press the relevant X or Y button to select the desired

enrollment mode 1 to 4 as indicated by the flashing of corresponding LEDs 1

to 4 (see the table for guidance on choosing the right enrollment mode).

• Activate the transmitter while the LED is flashing, as follows:

o key fob – press a button

o detector or thermostat – connect its battery up (if it has already been

connected, first disconnect it, and then wait 10 seconds)

o Control panel PG output – key in 299 in service mode

• Enrollment is confirmed by a short flash from all the AC-82 indicators

• If no enrollment signal has been received within 10 sec., enrollment mode

automatically ends.

• If you wish to enroll another device, repeat the above enrollment procedure.

Notes:

• If a device does not enroll, either it is too far from the receiver, or there is

another device already enrolled which cannot be combined with the new

one, or the maximum number of devices has been exceeded.

• Each device can have its own individual reaction (it is possible to combine

different reactions for a single relay = enrolling different devices in different

enrollment modes to the same relay).

• The relay always performs the last received instruction (e.g. if the relay is

already on and a signal for a 2 minute pulse is received, the relay will stay

on for another 2 minutes and then it will turn off).

• Each transmitting device (keyfob, detector, control panel, etc.) can be

enrolled to an unlimited number of different receivers.

• Devices are enrolled to a non-volatile memory, so the AC-82 will not forget

them if its power is disconnected

Use with RC-8x remote controllers

• Up to 60 remote controllers can be enrolled to each relay.

• To operate garage door or parking gate actuators, use the 1 sec. pulse

mode and connect the NC relay contact to the push button input of the

actuator unit.

Use with JA-8x wireless detectors

• Detectors can be enrolled to pulse modes 1 and 2 (up to 60 detectors to each

relay). The 2 minute mode is suitable for automatically switching on lights,

ventilators etc.

• If a detector(s) is enrolled in mode 3, then the relay will be switched if the

detector’s tamper sensor is triggered. In this mode up to 8 detectors can be

enrolled to a single relay (which will be switched if any of the detectors is

tampered with), but no other kind of device can be enrolled, only detectors.

• If a detector(s) is enrolled in mode 4, then the relay triggers if the detector’s

No. Reaction Device Enrollment method Max.

number Notes

keyfob button pressing

1 1 sec. pulse detector connecting battery up 60

• key fobs and detectors can be combined

• the relay stays on 1sec, turns off and is then ready to be activated again (the pulse is not

extended if another 1 sec. pulse activation signal is received while the relay is still on)

keyfob button pressing

2 2 min. pulse detector connecting battery up 60

• key fobs and detectors can be combined

• if another 2min. activation signal is received while the relay is on for 2 min., then the relay

stays on 2 min. more (the 2 minute pulse is extended if re-activated during the pulse)

Latch keyfob button pressing 60

3 Tamper = on detector connecting battery up 8

• impossible to combine keyfobs with detectors

• * latch = on – off – on – off….

• Tamper = on= relay turns on when a detector’s tamper sensor is triggered.

keyfob button pressing enrolls

a pair of buttons 60 • impossible to combine key fobs with detectors or with a control panel PG output

PG output of

control panel

entry of 299 in Service

mode 1 • impossible to combine PG output with detectors or with keyfobs

On / off

thermostat connecting battery up 8 • can be combined with keyfobs, detectors and a control panel PG output

Triggering = on detector connecting battery up 8 • impossible to combine detectors with keyfobs or with a control panel PG output

The AC-82 wireless relay output module MJT51202

sensor is triggered. In this mode up to 8 detectors can be enrolled to a single

relay (which triggers if any of the detectors is triggered), but no other kind of

device can be enrolled, only detectors.

• If the same detector is enrolled to relay X in mode 4 and to relay Y in

mode 3, then relay X will work as its sensor trigger output and the relay Y as

its tamper output.

Using the AC-82 with control panel PG output signals

• if the control panel is enrolled to the X relay (in mode 4 by entering 299) then

the X relay works as a control panel PGX output.

• if the control panel is enrolled to the Y relay (in mode 4 by entering 299) then

the Y relay works as a control panel PGY output.

• Only one control panel PG output can be enrolled to each relay. No other

transmitting devices can be enrolled to a relay already occupied by a control

panel PG output.

Using the AC-82 with TP-8x wireless thermostats

• If a thermostat is enrolled to a relay (enrolled in mode 4 by connecting its

battery up), then this relay can be used to control the heating.

• The enrollment of a thermostat to a relay is indicated by LED 1 for relay X

and LED 3 for relay Y.

• Up to 8 thermostats can be enrolled to each relay. A relay energizes if any

of the thermostats requires the heating to be on.

• Other devices can be combined with a thermostat and all be enrolled

to the same relay (a total of 8 devices, including the thermostat).

• Wireless devices enrolled together with a thermostat to a single relay

can be used to determine how that relay reacts signals from the

wireless thermostat. If desired, the relay can react only to the freezing

protection signal from the thermostat to turn on the heating when the

temperature gets below about +6C, or alternatively it can react to the

thermostat signal which demands heating when the room temperature

is lower than that pre-programmed in the thermostat. The relay can be

switched between these two modes by operating the wireless devices.

• If enrolled with a thermostat, the wireless devices have following

functions:

• Key fob RC-8x: A pair of buttons is enrolled. Pressing one button switches

the relay to regulating the heating to the pre-programmed temperature, and

pressing the other button switches the relay to regulating the heating to +6C

to avoid freezing. Multiple key fobs can be enrolled and can also be combined

with window detectors (see below).

• Window detectors: If a window is open, the relay reacts to the signals from

the JA-80M or JA-82M window detectors by switching to regulating the

heating to +6C to avoid freezing. Multiple window detectors can be enrolled

and they can be combined with key fobs too.

• Control panel (CP) PG outputs: To switch the relay between regulating the

temperature to the pre-programmed temperature or to +6C, the CP PG

outputs should be programmed in the CP to have an ON/OFF function (see

the CP manual). The heating mode can then be selected from devices able to

switch the CP PG output such as the alarm system keypad, keyfob or even a

detector programmed to control the PG output. It could also be done remotely

by phone or the Internet (if a suitable communicator is used in the control

panel). Remember that PGX can only be enrolled to the X relay, and PGY to

the Y relay (see the above section), and it is not recommended to enroll key

fobs or detectors to the same relay to which thermostat(s) and PG outputs

are enrolled as the control panel repeats currently valid PG signals every 9

minutes. If you wish to combine keypad operation with keyfobs, it is best to

enroll the keyfobs to the control panel and program them to control the PG

output which is enrolled to the relevant relay.

• If the relay is in the mode which regulates the heating to a pre-programmed

temperature, this is indicated by LED 1 for relay X, and LED 4 for relay Y. The

current contact status of relay X is shown by LED 2, with relay Y’s being

shown by LED 4.

• The thermostat repeats its signal every 9 minutes, so if the AC-82

power is turned off for a while, and then on again, the relay will

synchronize with the thermostat within 9 minutes.

• If you switch the relay to the mode for regulating the heating to the pre-

programmed temperature (e.g. by keyfob etc.), then the mode is

changed instantly, however, the relay will only switch the heating on

after the thermostat has sent an instruction to turn the heating on (i.e.

the heating system’s reaction can be delayed by up to 9 minutes after

the request has been sent).

Resetting the AC-82 unit

New AC-82 units are sold with factory-default settings (i.e. both relays

have nothing enrolled). To reset a particular relay, do the following:

• Repeatedly press the X button (or the Y button for the Y relay) to

achieve the highest number LED flashes (4, or if not possible, then 3).

• Then, continuously press the same button and keep pressing it until all

the LEDs flash a couple of times (= reset). Then release the button.

Inverting the relay function (to a N.C. contact)

Both relays have only normally open contacts. If a normally closed

contact function is required (e.g. to turn off an appliance if the alarm

system is armed), then you can invert the relay function as follows:

• First reset the AC-82 unit.

• Using button X for relay X (or button Y for relay Y) makes LED number

4 flash.

• Now keep both the X and Y buttons pressed until all the LEDs flash a

couple of times.

• The relay now has a normally closed contact function.

• To return it to its normal function, reset the AC-82 unit.

Note: Please remember, that if a relay has a normally closed contact function,

the relay will switch off if the AC-82 power is turned off.

Technical specifications

Power supply: 230V AC/50Hz, class protection II

Consumption about 1W

Relay contact rating

resistive load max. 2,5A / 250V AC

inductive (capacitive), lamp load max. 0,5A / 250V AC

Required fuse rating max. 5A

Communication band 868 MHz, Oasis protocol

Minimum distance from transmitting devices 1 meter

Dimensions, weight: 76 x 110 x 33 mm, antenna 35 mm, 120 g

Operating environment general, indoor –10 to +40 °C

Enclosure IP40 EN 60529

Mechanical immunity IK08 EN 50102

Complies with ETSI EN 300220, EN-50130-4, EN-55022 and EN 60950-1

Can be operated according to ERC REC 70-03

JABLOTRON ALARMS a.s. hereby declares that the AC-82 is in

compliance with the essential requirements and other relevant provisions of

Directive 99/5/EC The original of the conformity assessment can be found

at www.jablotron.com, Technical Support section

Note: Although this product does not contain any harmful materials we

suggest you return the product to the dealer or directly to the producer after

use.

Produkt Specifikationer

Mærke:	Joblotron
Kategori:	Overvågningskamera
Model:	AC-82

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron AC-82 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Joblotron Manualer

Joblotron H-915 Manual

13 Maj 2024

Joblotron JA-60 Manual

18 April 2024

Joblotron JA-63E Manual

17 April 2024

Joblotron SP-02 Manual

6 April 2024

Joblotron GS-130 Manual

6 April 2024

Joblotron UC-230 Manual

1 April 2024

Joblotron UC-261 Manual

27 Marts 2024

Joblotron JA-60M Manual

6 Marts 2024

Joblotron JA-80A Manual

6 Marts 2024

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Bosch FLEXIDOME panoramic 5100i Manual

30 Juni 2025

QNAP TVR-AI200 Manual

30 Juni 2025

Mobotix M73A Manual

29 Juni 2025

Lumens VC-R31 Manual

28 Juni 2025

TP-Link Tapo C460 Manual

28 Juni 2025

TP-Link Tapo C201 Manual

28 Juni 2025

TP-Link Tapo C403 Manual

27 Juni 2025

TP-Link Tapo C101 Manual

27 Juni 2025

AVer HUB30 Manual

26 Juni 2025

TP-Link Tapo C206 Manual

26 Juni 2025