LiftMaster 480LMC Manual

LiftMaster Ikke kategoriseret 480LMC

Læs gratis den danske manual til LiftMaster 480LMC (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 78 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 39.5 anmeldelser. Har du et spørgsmål om LiftMaster 480LMC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

To avoid possible SERIOUS INJURY to fingers from moving

garage door opener:

• Be sure power is not connected to the garage door opener

BEFORE installing the 480LM mounting kit.

• ALWAYS keep hand clear of chain and sprocket while

operating opener.

• Securely attach chain cover BEFORE operating.

Figure 2Figure 1

Models 480LM & 480LMC

Alternate Mounting Kit

INSTALLATION

1. Disassemble kit and remove foam pad (attached to

sprocket hub). Discard foam pad.

2. Attach the T-bracket to the motor unit using the

self-threading screws (Figure 1).

NOTE: The T-bracket will be above the existing mounting

bracket.

3. Attach sprocket with larger bore (1-1/4") to the motor

shaft of the opener. Position the sprocket so that the

screws are facing up and are accessible when

attached to the torsion bar (Figure 2).

4. Tighten both sides of the sprocket screws equally to

secure the sprocket to the motor unit (12-14 ft./lbs.

of torque). Securely tighten set screw.

CARTON INVENTORY

1T-bracket

21-1/4" Sprocket with Collar and Screws

31" Sprocket with Collar and Screws

4Chain

5Cover Assembly

NOT SHOWN

Hardware: 1/2" Screw (1),

#10 Self-Threading Screw (2),

and 1-1/2" Hex Head Screw (2)

Instructions 5

(provided with opener)

Figure 5

Figure 6 Figure 7

INSTALLATION

5. Attach sprocket with the smaller bore (1") to the

torsion bar making sure that the screws are on the

side closest to the garage door (Figure 3).

NOTE: Do not tighten sprocket at this time.

6. Place the chain on the sprocket located on the

torsion bar (Figure 4).

7. Attach the sprocket located on the motor unit shaft to

the chain. Secure the motor unit to the wall using the

hex head screws (Figure 5).

NOTE: Ensure that the chain is perpendicular to the bar

and not too tight.

8. Tighten both screws of the sprocket on the torsion

bar equally to secure the sprocket to the bar

(12-14 ft./lbs. of torque). Securely tighten set screw.

You may need to rotate the chain to make the

screws accessible.

9. One side of the chain cover will have an indentation

that will fit into the middle of the motor unit sprocket.

This side should be put on first (Figure 6).

10. Position the remaining cover over the other side so

that it encloses the chain and sprocket assembly.

The covers will snap into place. Secure them by

screwing them together using the 1/2" screw

(Figure 7).

11. Rotate chain to ensure smooth travel. Adjust, if

necessary.

12. Refer to Installation Step 2 of the owner’s manual for

further instructions.

Figure 4

Figure 3

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	480LMC

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 480LMC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

LiftMaster 64LM Manual

3 September 2024

LiftMaster CAPXSHOOD Manual

28 August 2024

LiftMaster myQ-SGC2WCH Manual

21 August 2024

LiftMaster CAPXS Manual

21 August 2024

LiftMaster MGJ5011U Manual

21 August 2024

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Milwaukee 3711 Manual

15 Juli 2025

Zoom RFX-1100 Manual

15 Juli 2025

Milwaukee 9573 Manual

15 Juli 2025

Auer Signal KLH Manual

15 Juli 2025

JUNG NRSCD0834 Manual

15 Juli 2025

JUNG 1712DE Manual

15 Juli 2025

Rockville RVSS2-XLR Manual

15 Juli 2025

Escort Shifter ZR3 Manual

15 Juli 2025

Zeiss Victory V8 1.8-14x50 Manual

15 Juli 2025

Ultimate Speed UAWSO 2 D1 Manual

15 Juli 2025