LiftMaster PPK3PHM Manual

LiftMaster Ikke kategoriseret PPK3PHM

Læs gratis den danske manual til LiftMaster PPK3PHM (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om LiftMaster PPK3PHM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

PASSPORT MAX REMOTE CONTROLS

To prevent possible SERIOUS INJURY or DEATH from a moving gate

or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER

permit children to operate, or play with remote controls.

• Activate gate or door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed.

NEVER permit anyone to cross path of moving gate or door.

Model PPV3M Models PPK3M and PPK3PHM

INTRODUCTION

The Passport MAX is a credentialed remote control. The Passport MAX

remote control is a versatile remote control that can be used on access

control systems, commercial door operators, gate operators, residential

garage door openers, and external receivers (Models PPWR, 850LM,

860LM, STAR1000) that use Security+ 2.0® or Security+ (315 Mhz and

390 Mhz) technology. The additional buttons on the remote control can

be programmed to operate up to 3 additional devices such as garage

door openers, light controls, gate operators or access control systems.

NOTE: Passport MAX credentialed remote controls are not compatible

with CPWR, CPWR3, RFMODKT, and RFMODKT3 Passport products.

NOTE: The images are for reference and your product may look different.

PROGRAMMING

Depending on your product, the LEARN button or LCD menu will be used

to program the remote control. 

If programming to an access control system or gated entry, contact your

property manager or LiftMaster® dealer for assistance with any

programming or operating instructions.

OPTION 1 – SECURITY+2.0 ® PRODUCTS

1. Locate the LEARN button on your product or the PROGRAM button on

the LCD (if applicable).

2. Press and release the yellow LEARN button on your product or the

PROGRAM button on the LCD. NOTE: The button color on commercial

products may vary.

3. Press andhold the remote control button you wish to use untilyour

product’s programming LED turns off orthe lights flash on your

product.

4. To test, press the programmed button on the remote control and the

product will activate.

OPTION 2 – SECURITY+ PRODUCTS (315 Mhz and 390 Mhz)

1. Locate the Program

button on the remote

control.

2. To enter the programming mode on the remote control, press the

program button until the LED on the front of the remote control turns

on.

3. Press and release the remote control button you wish to use:

• 2 times if your product is 315 MHz (Purple LEARN button)

• 3 times if your product is 390 MHz (Red/Orange LEARN button)

NOTE: The button color on commercial products may vary.

4. Exit programming mode by pressing any remote control button except

the button that was just programmed.

5. For LEARN button:

• Press and release the LEARN button on your product

For LCD:

• Press the navigation button below

“MENU” to view the Features menu on

the LCD. Use the navigation buttons to

scroll to “PROGRAM”. Select

“REMOTE” to program from the

program menu.

6. Press andhold the remote control button you programmed in Step 3

untilyour product’s programming LED turns off orthe lights flash on

your product.

7. To test, press the programmed button on the remote control and the

product will activate.

Program Button

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer or

birth defects or other reproductive harm. For more information go

to www.P65Warnings.ca.gov

ONE YEAR LIMITED WARRANTY

The Chamberlain Group, Inc. warrants to the first consumer purchaser of

this product that it is free from defect in materials and/or workmanship

for a period of 1 year from the date of purchase.

REPLACEMENT PARTS

3V CR2032 Lithium battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20

Visor Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B137

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of

this receiver and/or transmitter are prohibited, except for changing the code setting or replacing

the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)this device

must accept any interference received, including interference that may cause undesired operation.

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

• Replace ONLY with 3V CR2032 coin batteries.

• DO NOT recharge, disassemble, heat above 212° F (100° C) or

incinerate.

KEY CHAIN REMOTE

Pry open the case with a

screwdriver blade.

VISOR REMOTE

Pry open the case first in the

middle (1), then at each side

(2 and 3) with the visor clip.

Battery

PROGRAMMING (CONTINUED)

OPTION 3 – RE-PROGRAMMING FOR SECURITY+2.0 ® PRODUCTS

1. Locate the Program button on the remote control.

2. To enter the programming mode on the remote control, press the

program button until the LED on the front of the remote control turns

on.

3. Press and release the remote control button you wish to use:

• 1 time for SECURITY+2.0® product (Yellow LEARN button).

4. Exit programming mode by pressing any remote control button except

the button that was just programmed.

5. Press and release the yellow LEARN button on your product or the

PROGRAM button on the LCD. NOTE: The button color on commercial

products may vary.

6. Press andhold the remote control button you programmed in Step 3

untilyour product’s programming LED turns off orthe lights flash on

your product.

7. To test, press the programmed button on the remote control and the

product will activate.

HOW TO USE THE REMOTE CONTROL

Press and hold the button down until the door or gate starts to move.

For key chain remote controls with a proximity sensor, hold the remote

control 1-2" away from the reader face and wait for a confirmation beep

or LED from the reader. Operation of the proximity sensor varies

depending on the access control system. For additional information refer

to the owner’s manual for the access control system.

THE REMOTE CONTROL BATTERY

To replace battery, open the case as shown. Insert battery positive side

up (+). Replace the battery with only 3V CR2032 coin cell battery.

Dispose of old battery properly.

1-800-528-9131

LiftMaster.com

Produkt Specifikationer

Mærke:	LiftMaster
Kategori:	Ikke kategoriseret
Model:	PPK3PHM

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster PPK3PHM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LiftMaster Manualer

LiftMaster 041-0405-000 Manual

15 Juni 2025

LiftMaster LMHNTG Manual

4 September 2024

LiftMaster CAPXSTKPL Manual

3 September 2024

LiftMaster BG790 Manual

3 September 2024

LiftMaster 64LM Manual

3 September 2024

LiftMaster CAPXSHOOD Manual

28 August 2024

LiftMaster myQ-SGC2WCH Manual

21 August 2024

LiftMaster CAPXS Manual

21 August 2024

LiftMaster MGJ5011U Manual

21 August 2024

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Steiner ATLAS Manual

9 Juli 2025

VOREL 74441 Manual

9 Juli 2025

VOREL 17733 Manual

9 Juli 2025

Buxton BBS 7700 Manual

9 Juli 2025

9 Juli 2025

9 Juli 2025

9 Juli 2025

9 Juli 2025

Go-eCharger Gemini flex 22kW Manual

9 Juli 2025

Doepke DHS 4-125 FANA24DC Manual

9 Juli 2025