Microchip PIC16F1829 Manual

Microchip Ikke kategoriseret PIC16F1829

Læs gratis den danske manual til Microchip PIC16F1829 (14 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Microchip PIC16F1829, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/14

 2012 Microchip Technology Inc. DS01450A-page 1

AN1450

INTRODUCTION

In this application note, a PIC10F322 is being used to

implement a delay block/debouncer. The delay can be

set between 2 µs and 193 µs. This can be used

effectively as a noise discriminator, or for switch

debouncing.

When used as a delay block, the application can be

used to fix low-level timing issues on signals. When

used as a debouncer, it can debounce signals from a

mechanical switch so that a clean signal can feed other

circuitry.

The application makes use of the Configurable Logic

Cell (CLC) peripheral to produce fast switching on the

output (if desired). If the same application were written

using port logic only, there would be multiple instruction

cycles before the output would change in response to

an input. Using the CLC the signal can be routed

directly and only have propagation and gate delay

between the input and output signals. In order to get

the highest performance possible from the application,

it has been written in assembly.

The code has been written in-line (without subroutines)

to maximize switching performance of the application.

The code uses only 43 locations of program memory

(512 available), and one byte of RAM.

This application note was developed using a

PIC10F322 demo board (part # AC103011). Language

tool versions: MPASMWIN.exe v5.45, mplink.exe

v4.43, mplib.exe v4.43.

DELAY SETTINGS AND VALUES

Delays can be set between 2 µs and 193 µs in 750 ns

increments (using the 16 MHz internal clock). Delays

can easily be made longer if desired, by reducing the

clock speed or increasing the size of the delay loop.

Enabling/disabling of delays is configured in the code

by commenting/uncommenting the following lines of

code:

Independent rising and falling edge delay times can be

set in the following lines of code:

Voltage: 2.3 to 5.5V.

CALCULATING DELAY VALUES

There are two options for setting delay values, and they

are determined by commenting/uncommenting the

MS_DELAY definition:

1. 1 millisecond step size – this is useful for switch

debouncing with recommended settings of

FALLING_EDGE_DELAY = 100 ms, and

RISING_EDGE_DELAY disabled.

Delays are set in milliseconds.

2. 750 ns step size

With the part running at 16 MHz, there are 250 ns per

instruction cycle. The delay loop takes three instruction

cycles to execute, so 750 ns are added for each

incremental change in the countdown timer. There are

approximately eight instructions (2 µs) that will be

executed between an input change and an output

change, if the shortest possible delay is selected

(RISING_EDGE_DELAY or FALLING_EDGE_DELAY

= 1).

Operating current: ~ 2.4 mA (but can be reduced with

lower clock speed).

MODES OF OPERATION

Rising Edge Delay

In this mode, only the rising edge has a delay, and the

falling edge will drop immediately.

Author: Stephen Allen

Microchip Technology Inc.

;; 2 lines below enable rising and falling

edge delays

#define RISING_EDGE_DELAY

#define FALLING_EDGE_DELAY

;; specify length of falling and rising edge

below

RISE_EDGE_DELAY equ 0x01

FALL_EDGE_DELAY equ 0x01

#define MS_DELAY

;#define MS_DELAY

delay = 2 µs + (delay_value x 750 ns)

Delay Block/Debouncer

AN1450

DS01450A-page 2  2012 Microchip Technology Inc.

Falling Edge Delay (Pulse Extender)

In this mode, the rising edge will come up immediately,

and the falling edge will be delayed.

Rising and Falling Edge Delay

In this mode, the user has the option to set independent

rising and falling edge values.

The diagram below (Figure 1) shows the relationship

between the rising and falling edges. Signal edges are

marked for reference in the source assembly code

(delay.asm).

FIGURE 1: MEASUREMENT OF RISING AND FALLING EDGE DELAYS

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	PIC16F1829

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip PIC16F1829 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip AT7913 Manual

1 September 2025

Microchip ATmega1281 Manual

19 Juli 2025

Microchip ATtiny461 Manual

19 Juli 2025

Microchip ATxmega128D3 Manual

19 Juli 2025

Microchip ATxmega128D4 Manual

19 Juli 2025

Microchip ATTINY28 Manual

19 Juli 2025

Microchip ATTINY861 Manual

19 Juli 2025

Microchip ATmega1280 Manual

19 Juli 2025

Microchip ATtiny84A Manual

19 Juli 2025

Microchip ATmega645P Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Ambient Weather WS-1173A Manual

18 September 2025

Vestil APTS-2460 Manual

18 September 2025

Frilec KOBLENZ9314-340 Manual

18 September 2025

Lanaform Aqua Pleasure Manual

18 September 2025

Ambient Weather WS-2902D Manual

18 September 2025

Emerson CKS1702 Manual

18 September 2025

Vestil BOL-48-5.5 Manual

18 September 2025

Ambient Weather WS-HE01 Manual

18 September 2025

Ambient Weather TransformaFence Manual

18 September 2025

Ambient Weather EZ-48-3AB-125-35 Manual

18 September 2025