Roberts Stylus Manual
Læs nedenfor 📖 manual på dansk for Roberts Stylus (3 sider) i kategorien Radio. Denne guide var nyttig for 21 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/3
1
2
3
4
5
6
7
1312111098
Clear a work area.
Ensure the packaging is the right-way up.
Open the packaging carefully.
Lift out each item, identify it, and carefully place it to one side.
Top cover
Base unit with tone-arm
Turntable platter with belt
Rubber mat
Head-shell with cartridge
Counterweight for the tone-arm
Hinges x 2
Cables x 3, comprising
USB cable (type-A - type-B)
Stereo phono plugs - Stereo phono plugs
Stereo phono sockets - 3.5mm stereo plug
Mains power adaptor with EU and UK pin options
STEP 1 - Assembling your turntable STEP 2 - Setting the tracking force
What is in the Box?
Assembling the turntable (part 1)
Note: An incorrect tracking weight can have a signicant effect on the quality of the audio when playing records. If the
tracking weight is set too low or too high then excessive wear to the stylus or damage to the surface of the record may
be caused.
When removing the stylus cover, do not touch the stylus. Damage caused to the stylus by mishandling is not
covered by the guarantee. When balancing the tone-arm it is important that the stylus never contacts the
turntable platter, mat or base.
We recommend that all packaging is kept to allow
the turntable to be safely transported in the future.
Features
1. Counterweight
This is used to set the tracking force.
2. Anti-skating control
This is used to set the anti-skating force.
3. Cueing lever
Use this lever to lower and raise the tone-arm.
4. Tone-arm rest and securing clip
This holds the tone-arm in place when not in use.
5. Head-shell
This holds the cartridge and stylus.
6. 33 / 45 r.p.m. speed switch
Selects the speed for the record to be played.
7. Platter and rubber mat
Place the record here for playing.
8. Phono sockets (right and left)
Audio output to an amplier.
Red = Right channel; White = Left channel.
9. Pre-Amp On/Off Switch
Controls use of the built-in phono preamplier.
If connected to a Line or Aux input set this switch to On.
10. USB port
Connect to a computer for making recordings.
11. Auto Stop On/Off switch
Controls the use of the automatic switch off.
12. DC input socket
13. Power On/Off switch
1. Unwrap the base unit, taking care not to put pressure on the tone-
arm or the cueing lever.
2. Do not assemble the platter onto the base just yet. There is
less chance of damage to the cartridge and stylus if the tone-arm
is assembled and balanced rst.
3. Ensure that the tone-arm is locked on its rest with the securing clip.
4. Take the head-shell and identify the locating pin on the head-shell
connector. Do not remove the stylus cover at this time.
5. Align the locating pin on the head-shell connector with the slot in
the socket at the end of the tone-arm.
6. Gently push the head-shell into the tone-arm, at the same time
rotate the locking ring at the end of the tone-arm to pull the two
parts together. Note that the locking ring rotates anti-clockwise when
viewed from the front.
7. Tighten the locking ring gently by hand. Do not apply force or use
any tools.
8. Slide the counterweight on to the tone-arm, rotating it clockwise when
viewed from the rear until it engages and some slight resistance is
felt.
Note that the scale on the counterweight rotates freely. The
counterweight itself must be rotated in order to engage correctly
with the tone-arm.
Tone-arm
securing clip
Counterweight
Tone-arm
Head-shell Locating pin Tone-arm
Locking ring
Stylus cover
Stylus
1. Set the anti-skating control to zero.
2. Raise the cueing lever.
3. Unclip the tone-arm from its securing clip so that it
can move freely.
4. Take the head-shell and observe that it is currently
unbalanced. At this point the head-shell should drift
upwards.
5. Rotate the counterweight so that it moves further
onto the tone-arm.
6. Keep checking the balance by lowering the cueing
lever to see whether the tone-arm falls, rises or
remains level. Take care when lowering the tone-
arm that the stylus does not come into contact with
the turntable base.
You should ignore the scale on the front of the
counterweight at this time.
7. Adjust the counterweight further by rotating the
counterweight so that it moves in or out until the
tone-arm is balanced and remains level when the
cueing lever is lowered.
8. Carefully remove the stylus cover and adjust the
counterweight again until the tone-arm is balanced.
Counter-
weight
Balance the tone-arm Cueing lever (to raise
or lower the tone-arm)
Removing the stylus cover
Setting the anti-skating control to zero
9. When you have balanced the tone-arm, place it so that it is again secured on its rest using the securing clip.
10. Carefully replace the stylus cover.
11. Keeping the counterweight in place, rotate the scale on the front of the counterweight so that it reads zero.
12. We recommend that a tracking force of 3.0 grams is used for the supplied cartridge. The tracking force should not exceed
4.0 grams.
The counterweight adjusts the tracking force by 3.0 grams for one complete revolution. Therefore the scale on the
counterweight will read zero when the tone-arm is balanced and also when the tracking force is set to 3.0 grams.
13. Rotate the counterweight and scale together (clockwise, viewed from the rear) so that the counterweight moves further
towards the tone-arm pivot and so that the scale then reads the desired tracking force.
Please see the photos to the right showing the counterweight setting when rst balanced and then after setting the
tracking force. Note that the counterweight is closer to the tone-arm pivot after setting the tracking force.
14. Adjust the anti-skating control next to the tone-arm pivot so that it also reads 3.0 grams. Note that this adjustment should
normally be set to match the chosen tracking force. Anti-skating control set to 3.0 grams
Scale set to zero after balancing the tone-arm
Scale reads zero after setting to 3.0 grams
1. Unpack the platter and identify the drive belt.
2. Place the platter on the spindle. Use one of the holes in the platter to
access the drive belt and place it over the pulley of the drive motor.
3. Slowly rotate the platter by hand to ensure that it moves freely and
that the belt is not twisted.
4. Place the rubber mat on the platter.
5. Fit the two hinges onto the top cover. Note that the hinges are sprung
and will tend to spring away from the cover.
6. Locate the other end of the hinges in the two sockets at the rear of
the turntable base.
7. Lower the cover into place over the platter and tone-arm.
Hinges
Sockets
Cover
Drive
belt
Underside of
the platter
Drive belt
Platter
Access hole
in the platter
Hinges
Cover
Motor pulley
Step 3 - Assembling the turntable (part 2)
Produkt Specifikationer
| Mærke: | Roberts |
| Kategori: | Radio |
| Model: | Stylus |
Har du brug for hjælp?
Hvis du har brug for hjælp til Roberts Stylus stil et spørgsmål nedenfor, og andre brugere vil svare dig
Radio Roberts Manualer
24 Oktober 2024
4 Oktober 2024
3 September 2024
30 August 2024
26 August 2024
20 August 2024
16 August 2024
15 August 2024
5 August 2024
5 August 2024
Radio Manualer
- Radio Bosch
- Radio SilverCrest
- Radio Ozito
- Radio Denver
- Radio Sencor
- Radio Sony
- Radio EasyMaxx
- Radio Panasonic
- Radio Hager
- Radio Metabo
- Radio DeWalt
- Radio RYOBI
- Radio Philips
- Radio Lenco
- Radio Vitek
- Radio OK
- Radio AEG
- Radio Audio-Technica
- Radio Pioneer
- Radio Sharp
- Radio Logitech
- Radio Emos
- Radio Kenwood
- Radio Zeniq
- Radio Daewoo
- Radio Technaxx
- Radio Lowrance
- Radio MB Quart
- Radio Sennheiser
- Radio Harman Kardon
- Radio Garmin
- Radio Sanyo
- Radio Grundig
- Radio Makita
- Radio Nikkei
- Radio Motorola
- Radio Pyle
- Radio Argon
- Radio Furrion
- Radio Denon
- Radio Yamaha
- Radio Matsui
- Radio Biltema
- Radio Scansonic
- Radio Nedis
- Radio Sonoro
- Radio Logik
- Radio Kicker
- Radio Vonroc
- Radio Moulinex
- Radio Hama
- Radio Auna
- Radio Muse
- Radio Thomson
- Radio Hyundai
- Radio Aiwa
- Radio Milwaukee
- Radio JBL
- Radio AKAI
- Radio TriStar
- Radio Teufel
- Radio Clas Ohlson
- Radio Audio Pro
- Radio Pure
- Radio Smartwares
- Radio Trevi
- Radio Trust
- Radio Topcom
- Radio Adler
- Radio Black And Decker
- Radio Camry
- Radio Busch-Jaeger
- Radio Blaupunkt
- Radio Clint
- Radio JVC
- Radio Einhell
- Radio Sandstrøm
- Radio Stanley
- Radio Uniden
- Radio Clatronic
- Radio Quigg
- Radio Hikoki
- Radio Hilti
- Radio Hitachi
- Radio Noveen
- Radio BasicXL
- Radio Medion
- Radio Sweex
- Radio Festool
- Radio Cambridge
- Radio Tangent
- Radio König
- Radio TechniSat
- Radio Tivoli Audio
- Radio Bose
- Radio Constellation
- Radio Crosley
- Radio Alpine
- Radio EnVivo
- Radio Maginon
- Radio Navman
- Radio Parrot
- Radio Kärcher
- Radio Balance
- Radio Telefunken
- Radio Tronic
- Radio Exibel
- Radio Craftsman
- Radio Powerplus
- Radio Technics
- Radio Zebra
- Radio Jensen
- Radio Alecto
- Radio Icom
- Radio Olympia
- Radio HQ
- Radio Krüger&Matz
- Radio Schneider
- Radio Basetech
- Radio NGS
- Radio Radionette
- Radio Timex
- Radio Soundmaster
- Radio TERRIS
- Radio MT Logic
- Radio Kathrein
- Radio Victrola
- Radio GlobalTronics
- Radio Cobra
- Radio Bogen
- Radio Omnitronic
- Radio Telestar
- Radio Geneva
- Radio Porter-Cable
- Radio Bush
- Radio JUNG
- Radio Binatone
- Radio Dual
- Radio Telex
- Radio Salora
- Radio Sagem
- Radio AIC
- Radio Nevir
- Radio Teac
- Radio Imperial
- Radio TrekStor
- Radio Sven
- Radio Swan
- Radio Hertz
- Radio Albrecht
- Radio Scott
- Radio Veho
- Radio Yaesu
- Radio La Crosse Technology
- Radio Polk
- Radio Midland
- Radio Monacor
- Radio IRC
- Radio Audizio
- Radio JL Audio
- Radio Brennenstuhl
- Radio Sogo
- Radio Alba
- Radio RCA
- Radio Cotech
- Radio ECG
- Radio Renkforce
- Radio AudioSonic
- Radio Manhattan
- Radio SPC
- Radio Aquatic AV
- Radio Proline
- Radio Caliber
- Radio OneConcept
- Radio Switel
- Radio JGC
- Radio Numan
- Radio Easy Home
- Radio Be Cool
- Radio Brondi
- Radio Viper
- Radio Lexon
- Radio PerfectPro
- Radio ILive
- Radio Roth
- Radio Roadstar
- Radio Clarion
- Radio Watson
- Radio IHome
- Radio Dcybel
- Radio Acoustic Energy
- Radio Eton
- Radio GPO
- Radio Sirius
- Radio Majestic
- Radio Audiovox
- Radio CRUX
- Radio SACK It
- Radio Xhdata
- Radio Futaba
- Radio Sangean
- Radio Vimar
- Radio Power Dynamics
- Radio Oricom
- Radio Rockford Fosgate
- Radio Klein Tools
- Radio Oregon Scientific
- Radio Aluratek
- Radio GPX
- Radio Lenoxx
- Radio Terratec
- Radio Lexibook
- Radio Pinell
- Radio Stabo
- Radio Memphis Audio
- Radio Duronic
- Radio Boss
- Radio Ruark Audio
- Radio DAP-Audio
- Radio Kunft
- Radio GoGen
- Radio Lutron
- Radio Delta
- Radio BLUEPALM
- Radio Fusion
- Radio Audac
- Radio Boston Acoustics
- Radio AMX
- Radio H-Tronic
- Radio DreamGEAR
- Radio August
- Radio Xoro
- Radio Manta
- Radio Schwaiger
- Radio Steren
- Radio Orava
- Radio Reflexion
- Radio REVO
- Radio Artsound
- Radio Data-Tronix
- Radio Ferguson
- Radio Aconatic
- Radio Hitec
- Radio Equity
- Radio Icy Box
- Radio Tevion
- Radio Brigmton
- Radio Sunstech
- Radio Marquant
- Radio Nordmende
- Radio AudioAffairs
- Radio Coby
- Radio Mac Audio
- Radio Bigben Interactive
- Radio Bigben
- Radio Laser
- Radio Naxa
- Radio Ricatech
- Radio Mpman
- Radio Ices
- Radio Peaq
- Radio Freecom
- Radio Gira
- Radio Dnt
- Radio Karcher Audio
- Radio PAC
- Radio Infinity
- Radio Ruarkaudio
- Radio Go Green
- Radio Wolfgang
- Radio Linn
- Radio Elta
- Radio Iluv
- Radio Monitor Audio
- Radio Multiplex
- Radio Soundstream
- Radio Zolid
- Radio Sagemcom
- Radio Block
- Radio Woxter
- Radio View Quest
- Radio Noxon
- Radio Brionvega
- Radio Wet Sounds
- Radio Eissound
- Radio MTX Audio
- Radio Digitech
- Radio Tecsun
- Radio TFA Dostmann
- Radio Audisse
- Radio Kruger Matz
- Radio Intertechno
- Radio EKO
- Radio Videologic
- Radio Tivoli
- Radio Roswell
- Radio Intek
- Radio Digitalbox
- Radio Whistler
- Radio Xact
- Radio GME
- Radio NUVO
- Radio Narex
- Radio Tiny Audio
- Radio R-MUSIC
- Radio E-bench
- Radio Konig Electronic
- Radio Peha
- Radio SiriusXM
- Radio Sanwa
- Radio SW-Stahl
- Radio Sailor
- Radio SSV Works
- Radio Microlab
- Radio QFX
- Radio Voxx
- Radio Ices Electronics
- Radio AmpliVox
- Radio Elbe
- Radio GBS Elettronica
- Radio Sang
- Radio Gewiss
- Radio Axxess
- Radio Majority
- Radio Retekess
- Radio Wintal
- Radio Acoustic Solutions
- Radio Atlantis Land
- Radio Ranger
- Radio Weather X
- Radio Mebby
- Radio Yamazen
Nyeste Radio Manualer
20 November 2024
20 November 2024
19 November 2024
17 November 2024
17 November 2024
16 November 2024
16 November 2024
15 November 2024
3 November 2024
31 Oktober 2024