TechniSat Technitenne 60 Manual

TechniSat Ikke kategoriseret Technitenne 60

Læs gratis den danske manual til TechniSat Technitenne 60 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 13 anmeldelser. Har du et spørgsmål om TechniSat Technitenne 60, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Assembly and operation manual for TECHNITENNE 60

Item no. EAN Colour

0000/1060 4019588010604 Light gray

0003/1060 4019588310605 Anthracite

1 Usage

The DigitalSat antenna TECHNITENNE 60 is suitable for the re-

ception of the satellite signals in the KU band (10,7 - 12,75 GHz)

of geostationary satellites.

2 Safety instructions

• The antenna and all its parts must not be subjected to the

action of forces that could cause deformation. As a result of

the action of such forces, geometric deformations can occur

which impair the signal reception or result in the antenna

falling down.

• Improper installation of the antenna and lack of mainte-

nance may cause the antenna to loosen and drop at its at-

tachment points.

• The assembly and disassembly of the DigitalSat antenna

must be carried out by qualiﬁed personnel. Qualiﬁed per-

sons are persons who, due to their training and experience,

have sucient knowledge in the ﬁeld of SAT system installa-

tion and are familiar with relevant state occupational safety

and accident prevention regulations, guidelines and gener-

ally accepted rules of technology (e.g. VDE regulations, DIN

standards) to can therefore the assess the work-safe condi-

tion of the system

• When mounting the antenna, do not use any other parts

than the originate used by the manufacturer.

3 Assembly

1. Gradually and diagonally screw the reﬂector ① with the

screws ⑧ on the back plate ② to avoid distortion of the

reﬂector.

2. Fix the on-pipe ﬁing ③ with the screws ④ and mount the

mast clamps with the parts + ⑤ ⑥ ⑦.

3. Insert the antenna arm ⑨ through the opening of the re-

ﬂector into the back plate until it clicks into place.① ②

4. Mount an LNB using the retaining clamp ⑩ and the

screws ⑪

5. Mount the mounted antenna on a special antenna mast,

raer fastener or wall bracket with a maximum pipe diam-

eter of 50 mm.

6. Align the antenna with the satellite.

7. Tighten the nuts on the screws ④ with a torque of maxi-

mum. 7 Nm ﬁrmly.

8. Tighten the nuts ⑦ on the mast clamps with a torque of

maximum. 7 Nm ﬁrmly.

Aer the antenna has been assembled and the nuts tightened,

it should not rotate, either horizontally or vertically. However

if this is the case, the antenna must under no circumstances

continue used and must be disassembled.

If there are any doubts about the assembly procedure, infor-

mation should be sought from the point of sale or the man-

ufacturer and their instructions followed. Parts of the antenna

set, replaced while the antenna is used, must be of the same

quality as the original parts provided by the manufacturer.

4 Obligation to antenna inspection

At regular intervals, but at least once every 12 months, the user

has to check the ﬁxing of the antenna, whereby an expert tech-

nician who is professionally involved has to be assigned.

It is important to make sure that the antenna parts do not

carry any signs of cracking. For each inspection, check the at-

tachment of all bolts and nuts used in mounting the anten-

na by “tightening” it with the tools intended. In order not to

overwind the threaded, the maximum torque used must not

exceed 7 Nm.

The ﬁer must also check whether the connected elements are

not loose and check for any cracks in them. Defective elements

must immediately be replaced with good ones.

Regardless of the above, inspection of the antenna should also

performed aer a period of strong winds with speed exceed-

ing 80 km/h. It is forbidden to aach any additional elements

to the antenna, its arm and other parts, especially laundry lines,

nets, bird feeders, etc..

!Information prohibiting further use aer a defect

is founded

If errors are detected at the DigitalSat antenna or any part of

the antenna (such as cracks, corrosion), the user must removal

the antenna and replace it with a faultless one.

If the antenna is still covered by a warranty, information about

such a defect should be sent to the entity which bears liability

in such case. Complaints and any doubts about the correctness

of assembly and use of an antenna should be made at the

place of purchase or sent to the manufacturer.

It is recommended that an DigitalSat antenna and all associat-

ed parts should be replaced aer 10 years at the most.

5 Disposal/Recycling instructions

Electronic equipment must not be disposed of in domestic

waste. According to directive 2002/96/EC OF THE EUROPE-

AN PARLIAMENT AND COUNCIL of 27 January 2003 on waste

electrical and electronic equipment, it must be disposed of

professionally. At the end of its service life, take this device for

disposal at a designated public collection point.

The device bears the CE symbol and complies with all requisite EU standards.

Changes and printing errors reserved..

Duplication and reproduction only with the publisher‘s approval.

TechniSat and TECHNITENNE are registered trademarks of

TechniSat Digital GmbH · TechniPark · Julius-Saxler-Str. 3 · D-54550 Daun

000x/1060 02.2019

Produkt Specifikationer

Mærke:	TechniSat
Kategori:	Ikke kategoriseret
Model:	Technitenne 60
Bredde:	560 mm
Dybde:	440 mm
Højde:	650 mm
Vægt:	2000 g
Antal pr. pakke:	1 stk
Produktfarve:	Grå
Pakkedybde:	134 mm
Pakkebredde:	580 mm
Pakkehøjde:	654 mm
Materiale:	Stål
Placering:	Udendørs
Forstærkning:	35.3 dB