Whale Gusher Titan Manual

Whale Ikke kategoriseret Gusher Titan

Læs gratis den danske manual til Whale Gusher Titan (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Whale Gusher Titan, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Whale Gusher® Titan® Bilge Pumps
Models: BP4402, BP4410 and BP4429
READ CAREFULLY BEFORE INSTALLATION AND USE
To the Fitter: Check that the product is suitable for the intended
application, follow installation instructions and ensure operating
instructions are passed on to the end user.
To the User: Read the instructions carefully. (See parts diagram)
APPLICATION
This bilge pump is designed exhaust standing water. Output
capacity depends on installation conditions and pumping rate.
(see fig. 3)
Users should be aware that capacity may not be sufficient to cope
with rapid influx of water.
If it is intended for any other purpose or with any other liquid, it is
the users responsibility to ensure that the pump is suitable for the
intended use and, in particular, that the materials are fully
compatible with the liquids to be used. With all applications it is
important that a system of safe working practice is applied to
installation, use and maintenance.
INSTALLATION
The Gusher Titan is designed for mounting on or through deck, or
on or through bulkhead. The standard model (BP4402) allows
considerable flexibility in the choice of handle position in relation
to the direction of the flow.
To Change Flow Direction:
(a) Release the screws on both sides of the clamping ring
(b) Ease off the diaphragm and rotate body to new position
relative to the fork and diaphragm
(c) Reassemble diaphragm and clamping ring remembering to
tighten the clamping screws evenly on both sides.
Select a suitable position free from
obstructions where the pump can be
operated efficiently and comfortably
Avoid installations which require a
cockpit locker to be opened in order to
operate the pump.
To minimise pumping effort, site the
pump halfway (in height) between the
strumbox / strainer and hull outlet
To ensure good priming and flow, avoid sharp bends in
pipework and fit a Whale strumbox/strainer (incorporating a
non-return valve) which prevents the end of the hose sucking
against a flat surface and allows the water level to be
reduced to a minimum.
Ensure that the pump is installed to allow easy access for
servicing.
For Mounting On Bulkhead: (BP4402)
1. Use pump as a template, mark off and drill four 1/4”
(6mm) holes.
2. Check flow direction and secure the pump with 1/4”
(6mm) bolts.
3. Attach 1 1/2” (38mm) smooth bore reinforced hose with
stainless steel worm drive hose clips. Tighten to prevent air
leaks
4. With thru-hull discharge, make sure
that the discharge point is well above
the water line.
5. Check the installation for air leaks,
correct priming and discharge
For Mounting On Deck (BP4429) or Thru Deck/Bulkhead
(BP4410)
1. For the on deck or thru deck/bulkhead models, the inlet and
outlet directions can be reversed by following the instructions
and repositioning the handle.
2. For the on deck or thru deck/bulkhead models, the deck
thickness must be a minimum of 13mm (1/2”) and a maximum
of 25mm (1”)
3. For on deck model (BP4429) follow points 1-5 of previous
instructions.
4. With thru deck/bulkhead models (BP4410) a plastic
deckplate (DP8904) is supplied.
5. Position pump under deck and check flow direction. Work
the rubber gaiter up through the hole until its flange rests on the
deck. Secure the six 1/4” (6mm) countersunk mounting screws
provided.
6. As points 3 - 5 of previous instructions
OPERATION
The Gusher Titan ensures efficient throughput with an easy
pumping action. Full even strokes will obtain the best results.
The detachable handle is fitted with a lanyard and should be
safely secured close to the pump.
Gusher Titan output at 1m Lift and 0.5m Head
Fig 3: Performance table
Performance data is based on factory tests and is typical of
what may reasonably be achieved. Actual performance may
vary depending on installation and operating conditions.
Fig 1
Ouput At 60 strokes/min At 70 strokes/min
Gallons/min 20 23.2
Litres/min 90 105.6

Produkt Specifikationer

Mærke: Whale
Kategori: Ikke kategoriseret
Model: Gusher Titan

Har du brug for hjælp?

Hvis du har brug for hjælp til Whale Gusher Titan stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Whale Manualer

Whale

Whale Gusher 30 Manual

5 September 2024
Whale

Whale UF2214 Manual

5 September 2024
Whale

Whale Gusher 10 Mk3 Manual

5 September 2024
Whale

Whale InstantMatch Premium SDP303T Manual

5 September 2024
Whale

Whale Switch Connect BP1578 Manual

5 September 2024
Whale

Whale Instant Match SDP134Tn Manual

20 Juli 2024
Whale

Whale Orca 3000 Manual

19 Juli 2024
Whale

Whale Smartbail Manual

7 Juli 2024
Whale

Whale Gulper 320 Manual

7 Juli 2024
Whale

Whale Supersub Manual

7 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Goodwe

Goodwe GW9100K-MVS Manual

2 Januar 2026
DeWalt

DeWalt DXV23PLPTA Manual

2 Januar 2026
Brizo

Brizo RP90545 Manual

2 Januar 2026
Nokia

Nokia WHP-101 Manual

2 Januar 2026
Newport Brass

Newport Brass 1200-5603 Manual

2 Januar 2026
Blaupunkt

Blaupunkt GTr 10130 A Manual

2 Januar 2026
Newport Brass

Newport Brass 2940-5103 Manual

2 Januar 2026
SereneLife

SereneLife SLTWF61LED Manual

2 Januar 2026
Delta

Delta H550 Manual

2 Januar 2026
Newport Brass

Newport Brass 3200-5223 Manual

2 Januar 2026