Aeon Labs DSB45 Manual

Aeon Labs Ikke kategoriseret DSB45

Læs gratis den danske manual til Aeon Labs DSB45 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 135 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 68 anmeldelser. Har du et spørgsmål om Aeon Labs DSB45, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

English

GREAT BRITAIN • customer service

tel: 0845 300 9799 customerservice@clasohlson.co.uk www.clasohlson.com/uke-mail: internet:

1 2

Water

Ver. 20140723

Water Sensor

Art.no 36-5748 Model DSB45

Please read theentire instruction manual before using theproduct and

then save it for future reference. We reserve theright for any errors in

text or images and any necessary changes made to technical data.

In theevent of technical problems or other queries, please contact our

Customer Services.

For more information please visit www.aeotec.com for acomplete

instruction manual.

Things to consider:

• Other wireless equipment using thesame frequency band can

reduce thetransmission range.

• Therange of all wireless equipment depends on thetype of

obstacles located between thetransmitter and thereceiver

(e.g. aconcrete wall will interfere with thesignal more than

aplasterboard wall).

If you experience problems, try thefollowing:

• Turn off any other existing wireless equipment to check whether

this is thecause of theproblem.

• Reposition thewireless equipment, shorten thedistance between

thetransmitter and thereceiver or reduce thenumber of obstacles

(walls, furniture, etc.) between them.

Safety

• Never subject thesensor to high temperature, dust, heavy

vibration, impacts, humidity or moisture.

• Never attempt to dismantle or modify thesensor as it contains no

user-serviceable parts.

Product description

Battery powered, wireless water sensor for use with Zipabox Duo and

other Z-wave-system products, regardless of make.

Location

Detector

Thewater sensor can be used in

two ways. It can detect thepre-

sence of water in places that were

previously dry, or it can detect

theabsence of water where water

should be present. Thedetector

can be attached using theincluded

double-sided adhesive tape.

3. Set your Z-Wave control device to learning mode.

4. Push theZ-Wave button on thesensor to connect it to your

existing Z-Wave network.

5. If theconnection is successful, theLED indicator will shine steadily

for 10 minutes. During this period thesensor can be conﬁgured

from thecontrol device.

6. If thesensor needs to be re-conﬁgured later, you can press

the “Wake up” button. TheLED indicator will shine steadily for

10 minutes. During this period thesensor can be conﬁgured

from thecontrol device.

Uninstallation

1. Set your Z-Wave control device in removal mode and press

theZ-Wave button on thesensor to uninstall it.

2. TheLED indicator on thesensor will ﬂash for 8 seconds if

theuninstallation was successful.

3. If theuninstallation was unsuccessful, theLED indicator will shine

steadily for 8 seconds.

Reset

Hold theZ-Wave button in for 20 seconds to reset thesensor to factory

settings. If theresetting was successful, theLED indicator will shine

steadily for 2 seconds.

Care and maintenance

• Always remove thebatteries if theproduct is not to be used for

along time.

• Clean theproduct using alightly moistened cloth. Use only mild

cleaning agents, never solvents or corrosive chemicals.

Disposal

This product should be disposed of in accordance with local regulations.

If you are unsure how to proceed, contact your local council.

Specifications

Frequency 868.42MHz

Batteries 2×AAA/LR03

Range 30 m indoors,

100m outdoors in optimum conditions

Operating temperature –10 to +60 ºC/14–140 ºF

1. Sensor

2. Detector

Detection of rising water level

Decide on anacceptable highest water level and

place thedetector in asuitable place accordingly.

Detection of sinking water level

Decide on anacceptable lowest water level and

place thedetector in asuitable place accordingly.

Sensor

Thesensor should be placed

where it is not exposed to water or

moisture, 1 metre above theﬂoor

and no further than 30 metres

away from thecontrol device.

Mount thesensor with thelonger

sides perpendicular to theﬂoor.

1. Press thebutton on

theend of thesensor

and remove thebase.

2. Attach thebase to awall using

theincluded screws or double-

sided adhesive tape.

Note: If you mount thesensor using screws, ﬁrst make sure that there

are no hidden electrical cables or water pipes in thewall/ceiling which

could be damaged by drilling themounting holes.

Installation

1. Press thebutton on theend of thesensor and

remove thebase.

2. Remove theplastic tab to activate

thebatteries. TheLED indicator on thesensor

will ﬂash for 8 seconds.

Produkt Specifikationer

Mærke:	Aeon Labs
Kategori:	Ikke kategoriseret
Model:	DSB45

Har du brug for hjælp?

Hvis du har brug for hjælp til Aeon Labs DSB45 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Aeon Labs Manualer

Aeon Labs DSB45 Manual

29 Juni 2023

Aeon Labs ZW075-C16 Manual

3 Marts 2023

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Mykin MDW6004S Manual

31 December 2026

Waterstone 1750HC Manual

31 December 2026

Samsung MX-F830 Manual

31 December 2026

Kogan KAPFSPB100A Manual

31 December 2026

NUX PHT-2 Manual

31 December 2026

Blaupunkt Rome 1156M TYAL Manual

30 December 2026

Watson VM-210-FP Manual

30 December 2026

NUX PMX-2 Manual

30 December 2026

Samsung RA19F Manual

30 December 2026

NUX MG-200 Manual

30 December 2026