Alecto DVM-250 Manual

Alecto Babyalarm DVM-250

Læs nedenfor 📖 manual på dansk for Alecto DVM-250 (2 sider) i kategorien Babyalarm. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

INSTALLATION

BABY UNIT: (CAMERA)

Power:

1. Connect one of the supplied 5V power adaptors to the 5V

DC input of the baby unit.

2. Insert the adapter into a 230V wall socket.

Only use the supplied power adaptor.

Make sure that the baby can’t

touch the wire of the baby unit.

Place the baby unit at least

1-1.5 meters away from the baby

and bundle excess cable lengths

using tape or cable-ties specically designed for this purpose.

Table model or wall model:

You may place the baby unit loose on a table, cabinet or desk

or suspend it from a wall.

For wall mounting:

Drill two holes in the wall, next to each other and at a distance

from 2.1cm, then insert plugs and screws. Leave the head of

the screw protrude for several millimeters.

Suspend the baby unit by sliding the recesses in the camera

support over the screws in the wall and then pressing the

baby unit somewhat downward. Finally, neatly hide the adap-

tor cable using cable-ties.

Tips for placement:

• For use as a baby monitor: place the baby unit at least

1-1.5 meters away from your baby and make sure to

safely tuck away the adapter cable.

• The temperature protrudes from the rear of the baby unit.

Make sure this sensor hangs freely, unexposed to direct

sunlight and avoid heat from e.g. light bulbs.

parent unit switched off and power adaptor connected:

• orange light while the battery is being charged

• green light remains lit when the battery is fully charged

10. VOX indicator, illuminates when the VOX function is en-

abled

11. Antenna

12. Sound indicators, ashing when the baby is crying

13. Volume +/- buttons

14-17. , , and buttons

18. Built-in speaker (rear)

19. Foldable table support (rear)

BABY UNIT:

20. Antenna

21. Light sensor, for enabling

and disabling the night

view LED’s

22. Camera lens

23. This area contains the

infra-red LED’s for the

night view lighting (not vis-

ible to the naked eye)

24. Built-in microphone

25. Coupling ball, to properly

and accurately orientate

the baby unit

26. Built-in speaker

27. Temperature sensor

28. Power adaptor input

29. ‘PAIRING’ button, to regis-

ter (or re-register) the baby

unit on the parent unit

30. On/off switch with indicator

SYMBOLS IN THE DISPLAY

While using the parent unit, the following symbols may appear

in the display:

In the upper left corner, the signal strength is indicated:

strong reception

good reception

average reception

and poor reception

no reception

When talking to the baby, the talk-back symbol on the right

side of the antenna symbol will illuminate.

CAM1 In the upper right corner, the camera you’re currently

watching is indicated. When multiple cameras are connected

to the parent unit and you’ve enabled the scan function (to

automatically switch to the next camera screen every 10 sec-

onds), also the symbol will appear.

Next to the camera indication, the battery capacity is shown:

battery full

battery 3/4 full

battery 2/4 full

battery 1/4 full

the outline is red and ashing: the battery is nearly ex-

hausted and the parent unit may switch off at any moment

no battery inserted or the battery is not connected. While

charging, the battery symbol keeps scrolling until the battery is

fully charged.

While adjusting the volume, the current volume level

is shown in the right side of the display. When the

volume level is set to 0 (sound off), the ‘no sound’

icon will appear here.

When the volume is turned off, the symbol appears in the

upper part of the display to remind you that you’ve switched

off the sound.

Press the button to open the

menu. You’ll nd a description

of these functions further in this manual.

illuminates when the temperature alert is enabled. This

symbol starts ashing when the set limit is exceeded.

USE

The functions ‘Brightness’, ‘Lullabies’, ‘Multi-camera’,

‘Zoom’, Temperature display and alert’ and ‘VOX’

(screen and sound switch off automatically when the baby is

sleeping) are described on the other side of this user’s manual

underneath the header ‘MENU-OPERATED FUNCTIONS’.

BABY UNIT:

Switching on/off:

Slide the ON/OFF switch at the rear to the ON position to turn

on and slide to the OFF position to turn off. The green light

underneath the ON/OFF switch illuminates several seconds

after you’ve switched on the unit.

Automatic night vision:

The baby unit is provided with built-in infra-red LEDs; these

LEDs will switch on automatically when the baby room turns

dark and will switch of again when it becomes light.

The LEDs can illuminate objects up to a distance of

approximately 2 meters.

When it’s dark, that is when the night vision LEDs

are switched on, the images on the parent unit will be

displayed in black and white.

Attention: infra-red light cannot be perceived by the

human eye; that means you cannot tell whether the

infra-red LEDs are switched on with the naked eye.

PARENT UNIT:

Switching on/off:

press and hold for 2 seconds to turn off

Volume:

Use the + and - buttons to set the loudness of the sounds

from the baby room that you hear through the speaker of the

parent unit.

While adjusting, the volume level will be indicated on the display.

Talk-back function:

When the screen is enabled, press the button to talk to

your baby. Press and hold the button for as long as you’re

talking and release the button to listen.

Sound indicators:

In the middle of the upper part of the display you’ll nd 4

sound indicators indicating whether the baby is crying by

ashing. This allows you to watch over your baby when the

sound is set to a low level or is turned off, or when the baby

monitor is placed a bit further away in the room.

Automatic on/off function: (VOX)

When the baby is sleeping quietly or when the baby unit is not

picking up any sounds, you may have the display and sound

of the parent unit switch off automatically and back on again

as soon as the baby starts crying.

The sensitivity of the automatic on/off function can be adjusted

(see chapter MENU further in this user’s manual). Use the

VOX push-button to enable or disable this function; the VOX

indicator shows whether this function is enabled or disabled:

light off = VOX function off

(the images and sound are

transmitted continuously)

light on = VOX function on

(display and sound off while the

baby is sleeping)

To check in the meantime:

By briey pressing any button you may enable the display and

sound again for a short time to watch and listen to the baby.

After several seconds, the display and sound are turned off

again.

Battery weak (empty) notication:

When in use, the battery symbol in the upper right corner of

the display shows the battery capacity.

As soon as the battery capacity falls below 25%, the red

power LED will illuminate to inform you of this. It’s now recom-

mended to connect the adaptor to recharge the battery.

When the battery capacity further decreases to nearly empty,

this red battery symbol starts ashing. Also the power indica-

tor starts ashing in red and every 30 seconds several alert

tones are emitted for 10 to 15 minutes long. Now immediately

connect the adaptor otherwise the parent unit will switch itself

off within this time period.

USER’S MANUAL

DVM-250

INTRODUCTION

• The Alecto DVM-250 is a wireless baby monitor observa-

tion system, suitable for private use indoors.

• You can either watch and listen continuously or you can

have the baby monitor switch on.

• The Alecto DVM-250 meets all essential requirements

and other provisions as described in the European Direc-

tive 1999/5/EC.

• The declaration of conformity is

available on the website www.

alecto.nl

• Use of this equipment is allowed in all countries of the

EU. In France, Italy, Russia and Ukraine, only indoor use

is allowed.

ATTENTION

Before you start using the set, please remove any protective

foil from the parent unit and baby unit.

About this user’s manual:

This symbol represents a warning. To ensure safe use,

always adhere to the instructions described in this

documentation.

This symbol is followed by a user’s tip.

Always check the Alecto website for the most recent version of

this user’s manual.

FUNCTION OVERVIEW

PARENT UNIT:

1. Battery compartment (rear)

2. Power adaptor input

3. VOX on/off button

4. ENTER button for menu settings

5. MENU button

6. Talk-back button

7. Power on/off button

8. Built-in microphone

9. Power indicator:

parent unit switched on, power adaptor not connected:

• green light during normal use

• red light when the battery capacity is low

• ashing red light when the parent unit may switch off at

any moment due to a low battery capacity

parent unit switched on and power adaptor connected:

• ashing green light while the battery is being charged

• green light remains lit when the battery is fully charged

• For optimal range, it is advisable to set up the baby unit as

high as possible, free from large metal surfaces.

The baby unit is not waterproof and therefore suit-able

for indoor use only.

PARENT UNIT: (MONITOR)

Battery:

1. Open the battery compartment by sliding and clicking off

the battery cover at the rear.

2. Connect the battery plug in the battery compartment ac-

cording to the gure below and install the battery.

3. Click the battery cover back onto the parent unit.

Never connect the plug or install the battery by force.

Only install the supplied rechargeable Li-ion battery (3.7V,

1440mAh).

Power adapter:

1. Connect the other 5V power adapter on the left side of the

parent unit.

2. Insert the adapter into a 230V wall socket.

The battery starts charging as soon as you connect the power

adaptor. When using it for the rst time, please charge the

battery for at least 15 hours, even when the indicator shows a

fully charged battery.

Only use the supplied power adaptor.

General:

Fold out the support at the rear to place the parent unit onto a

table or cabinet.

Keep the antenna of the parent unit in an upright position for

optimal range.

The parent unit is not water-proof, hence is only suitable

for indoor use.

VOX

8 9 10 1211

218

119

1-1.5m

VOX

VOX indicator

Produkt Specifikationer

Mærke:	Alecto
Kategori:	Babyalarm
Model:	DVM-250
Vekselstrømsindgangsspænding:	220 - 240 V
Vekselstrømsindgangsfrekvens:	50 Hz
Produktfarve:	Hvid
Skærm diagonal:	5 "
Berøringsskærm:	Ingen
Indikator for batteriniveau:	Ja
Standby tid:	8 t
Strømkilde type:	Vekselstrøm
Maksimal indendørs rækkevidde:	50 m
Maksimal udendørsinterval:	300 m
ECO-tilstand:	Ja
Indbygget mikrofon:	Ja
Frekvensbånd:	2.4 GHz
Grænseflade:	FHSS
Maks. rækkevidde:	300 m
Temperaturføler:	Ja
Alarm for lavt batteri:	Ja
Automatisk advarsel om svigtende forbindelse:	Ja
Temperaturovervågning:	Ja