Aluratek ATL01F Manual

Aluratek Ikke kategoriseret ATL01F

Læs nedenfor 📖 manual på dansk for Aluratek ATL01F (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

Charging

port

Sensor

LED

Hook

Water

resistant

ring

Blue light ashﬂ

Wai ng for Blue �

light to touch

Wai ng for Blue �

t to touch

Flashing red

and blue light Solid blue light

Blue light ashﬂ

6 sec *Refer to “Fingerprint

Enrollment” sec on�

Red and blue

light ashﬂ

Wai ng for Blue �

light to touch

6 sec

Flashing red

and blue light

Wai ng for Blue �

light to touch

Wai ng for Red �

light to touch

Blue light for 2 sec

Activation

Press hook to activate the lock:

Note:

If the LED light is not activated,

please charge the lock using

the included micro-USB cable.

If no action is proceeded within

15 seconds after the lock is

activated, the power will be

turned off automatically.

Caution: Please set up your personalized Fast-Click Code after first fingerprint

registration IMMEDIATELY.

Fast-Click allows you to create a custom access code of short and long taps to manually

un-lock the lock without a computer. The Fast-Click code is a 6-digit code made up of a

string of 6 long and short taps.

Code Registration :

1.1 To enter the code registration mode:

- Tap and hold the hook for 5 seconds and wait for a flashing blue light, continue

holding until the red and blue light flashes.

1.2 Input your first Fast-Click digit:

- A long tap using the hook longer than 1 seconds, red and blue light turns on and

that indicates a successful registration of a long tap.

- A short tap is less than 1 second, LED change to a rapid flashing blue light,

indicates a successful registration of a short tap.

1.3 The red and blue light will flash rapidly after each successful registration.

1.4 Repeat step 2 until all 6 digits are successfully enrolled. After a code has been

successfully registered, a blue light will be activated and stay on for 4 seconds.

* Please write down your code after registration: __ __ __ __ __ __

Unlock Using Fast-Click Code or Change Your Code:

To Unlock:

2.1 Tap and hold the hook for 5 seconds and wait for a flashing blue light, continue

holding until the red and blue light flashes slowly.

2.2 Enter your registered code and wait until the blue light activates, that indicates the

code is entered correctly. The lock will be unlocked after 3 seconds.

2.3 If the code is entered incorrectly, a red light will be activated and turns into a slow

flashing red and blue light right after, then you can re-enter your registered

Fast-Click code.

* The lock will exit the Fast-Click Unlock Mode after 4 attempts of entering the wrong

code.

TouchLock Unlock Fingerprint Registration

Registration of Additional Fingerprints Erase Fingerprint Records

-In the unlikely event the battery dies while locked, TouchLock should be charged using

an external battery to provide quick access to un-lock, such as a Power Bank.

-Low battery warning: the red light will flash 3 times when the battery has 30% charge

left, it will flash continuously when it has 10% charge left

-Tip: try registering multiple fingers. Smaller profile fingers tend to work best.

FAQ

Aluratek warrants this product against defect in material or workmanship for 1 YEAR

from the date of purchase.

This warranty becomes invalid if the factory-supplied serial number or "warranty void" sticker has

been removed or altered on the product.

This warranty does not cover:

A) Cosmetic damage or damage due to acts of God

B) Accident, misuse, abuse, negligence or modification of any part of the product.

C) Damage due to improper operation or maintenance, connection to improper equipment,

or attempted repair by anyone other than Aluratek.

D) Products sold AS IS or WITH FAULTS.

IN NO EVENT SHALL ALURATEK'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT

FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES

RESULTING FROM THE USE OF THE PRODUCT, IT'S ACCOMPANYING SOFTWARE, OR

IT'S DOCUMENTATION.

Aluratek makes no warranty or representation, expressed, implied, or statutory, with respect to it's

products, contents or use of this documentation and all accompanying software, and specifically

disclaims it's quality, performance, merchantability, or fitness for any particular purpose. Aluratek

reserves the right to revise or update it's product, software or documentation without obligation to

notify any individual or entity.

Warranty

aluratek.com

model ATL01F

Quick Start Guide

All Weather Keyless Fingerprint Lock

Technical Support

If you need further assistance, please contact the Aluratek support department for

troubleshooting prior to returning this device.

E-mail: support@aluratek.com

Web: www.aluratek.com/helpdesk

Local (Irvine, CA): 714-586-8730

Toll free: 1-866-580-1978

TouchLock is a smart padlock. There is no need for keys or combinations. The lock can

store up to 20 fingerprints which easily allows you to share your lock with your family and

friends. Our TouchLock XL also comes with a waterproof rubber ring which allows the

locks to be used outdoors.

Reset the Lock Using PC Tool

3.1 Repeat the previous step 2.1,2.2 and tap the hook within 3 seconds after the blue light

is activated, then a rapid red blue light will flash, indicates a new code can be

enrolled. (The previous registered code will be erased automatically)

3.2 Repeat step 1.2,1.3 and 1.4 in Code Registration section to input your new

Fast-Click Code.

Erase the Fast-Click Code

-When clear all fingerprint record, Fast-Click code record would also be erased, method

please refer to erase fingerprint record section in this manual

Change or Erase Your Fast-Click Unlock Code

Press the hook once and

wait for the flashing blue

light.

Place your registered

finger on the touch sensor

and hold until you see the

solid

blue light

*If a red light flashes,

please place your finger on

the sensor and try again.

TouchLock will then unlock

once the registry is

confirmed.

*Finger recognition may

require multiple attempts

due to your placement of

the finger on the touch

sensor.

Press the hook once,

wait for the flashing red

and blue light;

Put your finger on the

sensor and wait for the

solid blue light

*If a red light flashes,

please put flatter part of

your finger on the sensor

and try again.

Repeat step 2 for three

times until you see a solid

blue light flashing for 4

seconds, indicating the

successful enrollment of

the fingerprint.

1. Press and hold hook

until you see the rapid

flashing blue light. Use a

previously registered

finger to authenticate.

After successful

authentication, the light will

change to a solid blue light

for a few seconds. If a red

light appears, lift finger

and retry. Immediately

following the solid blue

light, wait for the flashing

red and blue light.

2. Put your finger on the

sensor and wait for the

solid blue light

*If a red light flashes,

please put flatter part of

your finger on the sensor

and try again.

3. Repeat step 2 for three

times until you see a solid

blue light flashing for 4

seconds, indicating the

successful enrollment of

the fingerprint.

Press the hook for 6

seconds until you see the

rapid flashing blue light

Touch sensor with the

previously enrolled finger

until you see the solid blue

light.

*If a red light flashes,

please put your finger on

the sensor and try again.

Press the button again for

6 seconds when you see

the rapid flashing red and

blue light, then release the

button when you see the

rapid flashing red light.

Touch sensor with the

previously enrolled finger

again and wait for the

solid blue light flashes for

2 seconds.

All the enrolled fingerprints

are successfully erased.

Reset the Lock Using The TouchLock PC Tool (PC only)

1. Go to the following URL:

https://www.aluratek.com/bio-key-touchlock-tsa-all-weater-bio-lock-fingerprint-recognition/

2. Find the Downloads section on the product page and click the link "TouchLock_PC

Tool" to download the tool

3. Connect the lock to your computer's USB port via the included USB cable

4. Open the "TouchLock PC Tool" ZIP folder and click on the tool

5. Select "Unlock by Password" buttonas shown below:

*Note: The default password is “0000”

To erase all enrolled fingerprint records:

-Click on the “Delete Fingerprints”

-Click “yes” and enter 4 digit password.

-Then click “Confirm”.

Change the password:

1. Click on “change

password”

2. Enter the current 4 digit

password

3. Enter and confirm the new

4 digit password

Fast-Click Unlock Mode

Produkt Specifikationer

Mærke:	Aluratek
Kategori:	Ikke kategoriseret
Model:	ATL01F

Har du brug for hjælp?

Hvis du har brug for hjælp til Aluratek ATL01F stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Aluratek Manualer

Aluratek AWCPA01FB Manual

1 September 2024

Aluratek AULS03F Manual

1 September 2024

Aluratek AUH200F Manual

25 August 2024

Aluratek AWAGA01F Manual

25 August 2024

Aluratek AUPS01F Manual

25 August 2024

Aluratek AUM01F Manual

25 August 2024

Aluratek APAP01F Manual

25 August 2024

Aluratek AWLMC01F Manual

20 August 2024

Aluratek ABPM02F Manual

19 August 2024

Aluratek AHDDS100F Manual

16 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg KIT6PX Manual

23 December 2024

Smeg KIT6CX Manual

23 December 2024

Smeg GTA-6 Manual

23 December 2024

Lucide Casper i 79166/19/12 Manual

23 December 2024

Lucide Merlina 78193/30/66 Manual

23 December 2024

Lucide Pippa 77583/81/30 Manual

23 December 2024

Lucide Pia 45380/04/30 Manual

23 December 2024

Lucide Pia 45280/01/30 Manual

23 December 2024

Lucide Anaka 45179/03/30 Manual

23 December 2024

Lucide Zych 45156/01/97 Manual

23 December 2024