Amprobe VPC-10N Manual


Læs nedenfor 📖 manual på dansk for Amprobe VPC-10N (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Beeping
Beeping
Beeping
BeepingBeeping
VOLTAGE AND CONTINUITY TESTER
MODEL VPC-10N
Instruction Manual
Safety Information
l Never use the tester if it or its test leads appear damaged.
l Never apply more than 600V DC or 600V AC rms. between
any terminal and earth ground.
l If the LED turns on it indicates the presence of voltage at the
probe tips.
l When using the probes, do not touch the metal probe tips.
l Disconnect the live test lead before disconnecting the common
test lead.
l Before each use, verify the tester’s operation by measuring a
known voltage.
Automatic Operation
The tester automatically turns on when you place the probes
across a complete circuit. The tester selects continuity or DC or AC
voltage mode based on the resistance or voltage between the
probes. The tester automatically turns off when you remove the
probes from the complete circuit.
Measuring Voltage
Connect test leads across the source or load under measurement,
the LED turns on at between 70% and 100% of their rated
voltages.
DC Voltage AC voltage
600V DC maximum 600V RMS
Maximum 45 Hz to 66 Hz
Testing for Continuity
Turn off circuit power before testing. Beeper indicates shorts lasting
1ms or longer
OPEN short or 0-85KW
Non-contact AC Voltage (NCV) detection operating
instructions
WARNING: Risk of Electrocution. High-voltage circuit, both AC and
DC, are very dangerous and should be measured with great care.
WARNING: Risk of Electrocution. Before using to check for voltage
in an outlet, always test the Voltage Tester on a known live circuit to
verify that the Voltage Tester is working properly.
WARNING: Risk of Electrocution. Keep hands and fingers on the
body of the probe and away from the probe tip. Dont touch
conductor.
1. T o check for AC voltage, assure the bottle shaped protrusion of
the fixed probe, see figure below, is in close proximity to the hot
conductor. The LED in the fixed probe will illuminate.
2. To check for the presence of AC voltage at an outlet, using the
NCV LED, insert either probe tip into the outlet’s hot side. If the
black probe is used only the NCV LED will illuminate. If the
fixed probe is inserted not only will the NCV LED illuminate but
some of the LEDs on the front of the instrument will illuminate
also. In this application these LEDs wont indicate the correct
voltage and should be ignored.


Produkt Specifikationer

Mærke: Amprobe
Kategori: Ikke kategoriseret
Model: VPC-10N

Har du brug for hjælp?

Hvis du har brug for hjælp til Amprobe VPC-10N stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Amprobe Manualer

Amprobe

Amprobe AD40B Manual

28 September 2024
Amprobe

Amprobe TMD-55W Manual

19 August 2024
Amprobe

Amprobe THWD-10W Manual

15 August 2024
Amprobe

Amprobe WT-20 Manual

13 August 2024
Amprobe

Amprobe VPC-10 Manual

12 August 2024
Amprobe

Amprobe TP110KA Manual

11 August 2024
Amprobe

Amprobe BAT-100 Manual

11 August 2024
Amprobe

Amprobe AT-4001-A Manual

4 August 2024
Amprobe

Amprobe FLASH-80 Manual

4 August 2024
Amprobe

Amprobe AC50A Manual

4 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024