Aruba 205H Manual

Aruba Adgangspunkt 205H

Læs nedenfor 📖 manual på dansk for Aruba 205H (2 sider) i kategorien Adgangspunkt. Denne guide var nyttig for 26 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Aruba AP-205H Wireless Access Point

Installation Guide

The Aruba AP-205H access point is a high-performance dual radio wireless and

wired access point for hospitality and branch deployments.

This device combines high-performance wireless mobility with Gigabit wired

local access to deliver secure network access to dormitories, hotel rooms,

classrooms, medical clinics, and multi-tenant environments. MIMO (Multiple-

Input, Multiple-Output) technology enables the AP-205H to provide wireless 2.4

GHz 802.11n and 5 GHz 802.11n/ac functionality, while simultaneously

supporting existing 802.11a/b/g wireless services.

The AP-205H can be attached to a wall box using the bracket provided, or

converted into a desk-mounted remote access point for branch office

deployments using the AP-205H-MNTR desk mount kit (sold separately).

The AP-205H access point works in conjunction with an Aruba controller, while

the IAP-205H variant uses a built-in virtual controller.

The Aruba AP-205H access point provides the following capabilities:

Dual wireless transceivers

IEEE 802.11a/b/g/n/ac operation as a wireless access point

IEEE 802.11a/b/g/n/ac operation as a wireless air monitor, spectrum analyzer

Compatibility with IEEE 802.3af/at PoE

Central management configuration and upgrades through an Aruba

Controller or Aruba Instant virtual controller

Supports PoE-in to E0 port (only)/PoE-out from E3 port (only)

Support for selected USB peripherals

Package Contents

AP-205H Access Point

Single Gang Wall-box Mounting Bracket

2x #6-32 Machine Screw

T8H Torx Security Screw

Installation Guide (this document)

Hardware Overview

Figure 1 Front

LED

The AP-205H is equipped with two LEDs indicating System Status and PSE.

Console Port

The IAP-205H access point is equipped with a serial console port at the

back( ). The port allows connecting the AP to a serial terminal or a Figure 2

laptop for direct local management. The 4-pin connector with removable dust

cover is located on the back of the access point. An optional serial adapter cable

(AP-CBL-SER) compatible with the IAP-205H can be purchased separately.

Figure 2 Rear

Ethernet Ports

AP-205H access point is equipped with a total of four active Ethernet ports (E0-

E3).

The E0, located at the back of the AP ( ) is 10/100/1000 Base-T (RJ-45) Figure 2

auto-sensing, MDI/MDX wired-network uplink connectivity port. It supports

IEEE 802.3af/802.3at Power over Ethernet (PoE), accepting 48VDC as a

standeard defined Powered Device (PD) from Power Sourcing Equipment (PSE),

such as a midspan injector or network infrastructure that supports PoE.

The E1-E3 ports, located at the bottom of the AP ( ), are 10/100/1000 Figure 3

NBase-T (RJ-45) auto-sensing, MDI/MDX wired-network downlink connectivity

ports. They are used to provide secure network connectivity to wired devices.

Only the E3 port supports PoE-out functionality, supplying a maximum power of

10W when the AP is operating in 802.3at PoE mode.

Additionally, the IAP-205H access point has a Pass-Through (PT) port at the

back ( ) and an E0/PT port at the bottom ( ). The E0/PT port acts Figure 2 Figure 3

primarily as a Pass-Through (PT) port. Alternatively, the E0/PT port can serve as

an E0 uplink port and accepts 802.3af/802.3at PoE power when the E0 and PT

ports at the back of the AP are physically bridged by an Ethernet cable.

AP-CBL-ETH10 sold separately with the AP-205H-MNTR desk mount kit.

Figure 3 Bottom

Figure 4 Gigabit Ethernet Port Pin-Out

USB Port

The AP-205H access point is equipped with a USB port that is compatible with

cellular modems and Bluetooth Low Energy (BLE) dongles. When active, the

USB port can supply up to 5W (1A).

Push Button

The push button located on the right side of the AP can be used to reset the AP to

factory default settings or turn off/on the LED display.

To reset the AP to factory default settings:

1. Power off the AP.

2. Press and hold the push button using a small, narrow object, such as a

paperclip.

3. Power-on the AP without releasing the push button. The system status

LED will flash within 5 seconds.

4. Release the push button.

The system status LED will flash again within 15 seconds indicating that the

reset is completed. The AP will now continue to boot with the factory default

settings.

To turn off/on the system status LED:

During the normal operation of the AP, press the push button using a small,

narrow object, such as a paperclip. The system status LED will be turned off/

on immediately.

Power Supply

The AP-205H has a single 48V DC power connector to support powering through

an AC-to-DC power adapter. AP-AC-48V36 sold separately.

The AP-205H supports both PoE-in and PoE-out functionality. The PoE-in (PoE-

PD) allows the E0 port to draw power from 802.3at (preferred) and 802.3af

(optional) sources.

When operating in 802.3at mode, the PoE-out (PoE-PSE) functionality is enabled

on port 3, allowing a maximum output of 10W. If a device attempts to exceed the

10W power limit, the E3 port is temporarily disabled. This port automatically

reactivates over time.

When operating in 802.3af mode, theAP-205H power to PoE-PSE and USB is

disabled.

Before You Begin

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their

placement have been determined, the Aruba controller(s) must be installed and

initial setup performed before the Aruba APs are deployed.

AP Pre-Installation Checklist

Before installing your AP-205H access point, be sure that you have the following:

Pre-installed wall box

Cat5E UTP cable with network access installed in the wall box

One of the following power sources:

IEEE 802.3af-compliant Power over Ethernet (PoE) source

Aruba AP AC-DC adapter kit (sold separately)

Aruba Controller provisioned on the network:

Layer 2/3 network connectivity to your access point

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor-specific options

Summary of the Setup Process

Complete each of tasks below in the order listed to setup your AP-205H access

point.

1. Verify pre-installation connectivity.

2. Identify the specific installation location for each AP.

3. Install each AP.

4. Verify post-installation connectivity.

5. Configure each AP.

Verifying Pre-Installation Connectivity

Before you install APs in a network environment, make sure that the APs are

able to locate and connect to the controller after power on. In order to

successfully setup your network the following conditions must be met:

When connected to the network, each AP is assigned a valid IP address

APs are able to locate the controller

Refer to the Guide for instructions on locating and ArubaOS Quick Start

connecting to the controller.

Identifying Specific Installation Locations

When installing the AP-205H access point must be secured to an Aruba approved

wall or to a desk mount kit, which can be purchased separately. This AP should

be oriented vertically, with Ethernet ports facing downward to facilitate

maximum antenna gain. Use the AP placement map generated by Aruba’s RF

Plan software application to determine the proper installation location(s). Each

location should be as close as possible to the center of the intended coverage

area and should be free from obstructions or obvious sources of interference.

These RF absorbers/reflectors/interference sources will impact RF propagation

and should be accounted for during the planning phase and adjusted for in RF

plan.

The Aruba AP-205H requires ArubaOS 6.4.3 or later.

Inform your supplier if there are any incorrect, missing, or

damaged parts. If possible, retain the carton, including the

original packing materials. Use these materials to repack and

return the unit to the supplier if needed.

Table 1

LED Color/State Meaning

System Status Off AP powered off, or LED switched to ‘off

mode’

Amber- Solid AP ready, restricted mode:

10/100Mbps uplink negotiated

Either radio in non-HT mode

Virtual AP not enabled

Amber- Flashing AP in Air or Spectrum Monitor mode

Red Error condition

Green - Flashing AP booting, not ready

Green - Solid AP ready

PSE Off AP powered off, or PoE capability disabled

Green - Solid PoE power enabled

Red PoE power sourcing error or overload

condition

The rear panel of the AP-205H may become hot after extended use.

Le panneau arrière du point d'accès AP-205H peut chauffer après

une utilisation prolongée.

Hot-plug operation is not recommended for the console port.

The USB interface is disabled when the AP-205H is powered from

802.3af PoE.

Table 2 Maximum Power Outputs

Power Source Restrictions USB PoE-PSE

DC (AP-AC-48V36) None 5W 15.4W

802.3at USB disabled when PoE-PSE is on 5W 10W

802.3af USB, PoE-PSE disabled N/A N/A

If both POE and DC power are available, the AP will default to using

DC.

FCC Statement: Improper termination of access points

installed in the United States configured to non-US model

controllers will be in violation of the FCC grant of equipment

authorization. Any such willful or intentional violation may

result in a requirement by the FCC for immediate termination

of operation and may be subject to forfeiture (47 CFR 1.80).

Déclaration FCC: l'arrêt incorrect des points d'accès installés

aux États-unis qui sont configurés sur des contrôleurs autres

que le modèle agréé aux États-unis est considéré comme

contrevenant à l'homologation fcc. toute violation délibérée ou

intentionnelle de cette condition peut entraîner une injonction

d'arrêt immédiat de son utilisation par la fcc et peut

déboucher sur la confiscation de l'équipement (47 cfr 1.80).

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5

GHz bands. Please refer to the ArubaOS User Guide for details

on restrictions.

Produit réseau local radio basse puissance operant dans la

bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au

ArubaOS User Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz

Band arbeitet. Weitere Informationen bezlüglich

Einschränkungen finden Sie im ArubaOS User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5

GHz. Fare riferimento alla per avere ArubaOS User Guide

informazioni detagliate sulle restrizioni.

It is important that you verify the items listed under AP Pre-

Installation Checklist before you attempt to set up and install an AP-

205H.

Aruba Networks, Inc., in compliance with governmental

requirements, has designed the AP-205H access points so that

only authorized network administrators can change the settings.

For more information about AP configuration, refer to the ArubaOS

Quick Start Guide and ArubaOS User Guide.

Access points are radio transmission devices and as such are

subject to governmental regulation. Network administrators

responsible for the configuration and operation of access points

must comply with local broadcast regulations. Specifically, access

points must use channel assignments appropriate to the location in

which the access point will be used.

Les points d'accès sont des périphériques de transmission radio et

sont, en tant que tels, soumis aux réglementations nationales. Les

administrateurs réseau responsables de la configuration et de

l'exploitation des points d'accès doivent se conformer aux

règlements locaux de diffusion. De façon plus précise, les points

d'accès doivent employer des canaux adaptés à leur emplacement

physique

Produkt Specifikationer

Mærke:	Aruba
Kategori:	Adgangspunkt
Model:	205H

Har du brug for hjælp?

Hvis du har brug for hjælp til Aruba 205H stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Adgangspunkt Aruba Manualer

19 September 2024

5 September 2024

28 August 2024

28 August 2024

Aruba Instant IAP-175 Manual

10 August 2024

Aruba AP-93H Manual

9 August 2024

Aruba AP-567 Manual

5 August 2024

Aruba Instant IAP-175P Manual

3 August 2024

Aruba Instant RAP-108 Manual

1 August 2024

Aruba AP-214 Manual

31 Juli 2024

Adgangspunkt Manualer

Nyeste Adgangspunkt Manualer

16 December 2024

15 December 2024

15 December 2024

15 December 2024

15 December 2024

15 December 2024

Vimar 14195.SL Manual

15 December 2024

Vimar 20195.B Manual

15 December 2024

Vimar 19195.B Manual

15 December 2024

TP-Link Festa F65-Outdoor Manual

11 December 2024