Asrock Fatal1ty FM2A88X+ Killer Manual

Asrock Bundkort Fatal1ty FM2A88X+ Killer

Læs nedenfor 📖 manual på dansk for Asrock Fatal1ty FM2A88X+ Killer (75 sider) i kategorien Bundkort. Denne guide var nyttig for 19 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/75
Version 1.0
Published December 2013
Copyright©2013 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535;
7,003,467 & other U.S. and worldwide patents issued & pending. DTS, the Symbol, &
DTS and the Symbol together is a registered trademark & DTS Connect, DTS Interactive,
DTS Neo:PC are trademarks of DTS, Inc. Product includes soware.
© DTS, Inc., All Rights Reserved.
Who knew that at age 19, I would be a World Champion PC gamer. When I was 13, I actually
played competitive billiards in professional tournaments and won four or ve games oguys
who played at the highest level. I actually thought of making a career of it, but at that young
age situations change rapidly. Because I’ve been blessed with great hand-eye coordination and
a grasp of mathematics (an important element in video gaming) I gravitated to that activity.
GOING PRO
I started professional gaming in 1999 when I entered the CPL (Cyberathlete Professional
League) tournament in Dallas and won $4,000 for coming in third place. Emerging as one
of the top players in the United States, a company interested in sponsoring me ew me to
Sweden to compete against the top 12 players in the world. I won 18 straight games, lost
none, and took rst place, becoming the number one ranked Quake III player in the world
in the process. Two months later I followed that success by traveling to Dallas and defending
my title as the world’s best Quake III player, winning the $40,000 grand prize. From there
I entered competitions all over the world, including Singapore, Korea, Germany, Australia,
Holland and Brazil in addition to Los Angeles, New York and St. Louis.
WINNING STREAK
I was excited to showcase my true gaming skills when defending my title as CPL
Champion of the year at the CPL Winter 2001 because I would be competing in a totally
dierent rst person shooter (fps) game, Alien vs. Predator II. I won that competition and
walked away with a new car. e next year I won the same title playing Unreal Tournament
2003, becoming the only three-time CPL champion of the year. And I did it playing a
different game each year, something no one else has ever done and a feat of which I am
extremely proud.
At QuakeCon 2002, I faced o against my rival ZeRo4 in one of the most highly
anticipated matches of the year, winning in a 14 to (-1) killer victory. Competing at Quakecon
2004, I became the World’s 1st Doom3 Champion by defeating Daler in a series of very
challenging matches and earning $25,000 for the victory.
Since then Fatal1ty has traveled the globe to compete against the best in the world, winning
prizes and acclaim, including the 2005 CPL World Tour Championship in New York City for
a $150,000 rst place triumph. In August 2007, Johnathan was awarded the rst ever Lifetime
Achievement Award in the four year history of the eSports-Award for “showing exceptional
sportsmanship, taking part in shaping eSports into what it is today and for being the prime
representative of this young sport. He has become the gurehead for eSports worldwide”.
Fatal1ty Story
LIVIN’ LARGE
Since my rst big tournament wins, I have been a “Professional Cyberathlete”, traveling the
world and livin’ large with lots of International media coverage on outlets such as MTV,
ESPN and a 60 Minutes segment on CBS to name only a few. It's unreal - it's crazy. I’m living
a dream by playing video games for a living. I’ve always been athletic and took sports like
hockey and football very seriously, working out and training hard. is discipline helps me
become a better gamer and my drive to be the best has opened the doors necessary to become
a professional.
A DREAM
Now, another dream is being realized – building the ultimate gaming computer, made
up of the best parts under my own brand. Quality hardware makes a huge difference in
competitions…a couple more frames per second and everything gets really nice. It’s all about
getting the computer processing faster and allowing more uid movement around the maps.
My vision for Fatal1ty hardware is to allow gamers to focus on the game without worrying
about their equipment, something I’ve preached since I began competing. I don’t want to
worry about my equipment. I want to be there – over and done with - so I can focus on
the game. I want it to be the fastest and most stable computer equipment on the face of the
planet, so quality is what Fatal1ty Brand products represent.
Johnathan “Fatal1ty” Wendel
e Fatal1ty name, Fatal1ty logos and the Fatal1ty likeness are registered trademarks of Fatal1ty, Inc., and are used
under license. © 2013 Fatal1ty, Inc. All rights reserved. All other trademarks are the property of their respective
owners.
1
English
Fatal1ty FM2A88X+ Killer Series
Motherboard Layout
Sup er
I/O
CMOS
BATTERY
ATXPWR1
PCIE1
PCI1
CPU_F AN1
64Mb
BIOS
PCIE2
CP U_F AN2
FM2A88X+ K rille
PCIE4
DDR3_A1 (64 bit, 240-pin module)
DDR3_A2 (64 bit, 240-pin module)
DDR3_B1 (64 bit, 240-pin module)
DDR3_B2 (64 bit, 240-pin module)
PW R_FA N1
CHA _FA N3
PCIE3
PCI2
PCI3
1
CL R C MO S1
HD LED ES ET R
PL ED PW RBT N
1
PANEL 1
SATA3 _1 _2SATA3 _3 _4SATA3 _5 _6SATA3 _7 _8
CH A_F AN 1 CHA_F AN 2
SP EA KE R1
1
PL E D1
1
HD_AUDIO 1
1
C O M1
1
1
USB _7_8
1
USB _9_10
Top:
CT R BASS
Ce nte r:
REAR SP K
Bo t to m:
Op tic al
SPDIF
Top:
LINE IN
Ce nte r:
FRONT
Bo t to m:
MIC IN
Top:
RJ- 45
VGA1
DVI 1
US 3.B 0
T: USB1
B: USB 2
HDMI1
Clr
CMOS
US 3.B 0
T: USB3
B: USB 4
US 2.B 0
T: USB3
B: USB4
USB 3_5_6
RoHS
SOCKET FM2b
AMD
A88X
(Bolton-D4)
Chipset
US 2.B 0
T: US B 1
B: USB 2
PS2
K /eyboard
Mous e
1
USB _5_6
T P MS1
1
CI 1
1
2 3 4 51 6
7
8
11
10
12
14
161820 172125 222326 19
27
ATX 112 V
13
SLI /XF IRE _ PWR 1
24
K rille
E2200
Purit y
Sound
T M
FATAL TY1
9
15
2
English
No. Description
1 ATX 12V Power Connector (ATX12V1)
2 Power Fan Connector (PWR_FAN1)
3 CPU Fan Connector (CPU_FAN1)
4 CPU Fan Connector (CPU_FAN2)
5 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_B1)
6 2 x 240-pin DDR3 DIMM Slots (DDR3_A2, DDR3_B2)
7 ATX Power Connector (ATXPWR1)
8 USB 3.0 Header (USB3_5_6)
9 Chassis Fan Connector (CHA_FAN3)
10 SATA3 Connectors (SATA3_1_2)
11 SATA3 Connectors (SATA3_3_4)
12 SATA3 Connectors (SATA3_5_6)
13 SATA3 Connectors (SATA3_7_8)
14 System Panel Header (PANEL1)
15 Chassis Fan Connector (CHA_FAN2)
16 Chassis Speaker Header (SPEAKER1)
17 Chassis Fan Connector (CHA_FAN1)
18 Power LED Header (PLED1)
19 Chassis Intrusion Header (CI1)
20 USB 2.0 Header (USB_9_10)
21 USB 2.0 Header (USB_7_8)
22 USB 2.0 Header (USB_5_6)
23 TPM Header (TPMS1)
24 SLI/XFIRE Power Connector (SLI/XFIRE_PWR1)
25 COM Port Header (COM1)
26 Front Panel Audio Header (HD_AUDIO1)
27 Clear CMOS Jumper (CLRCMOS1)
3
English
Fatal1ty FM2A88X+ Killer Series
I/O Panel
No. Description DescriptionNo.
1 Fatal1ty Mouse Port (USB_1)* 10 Microphone (Pink)
2 USB 2.0 Port (USB_2)* Optical SPDIF Out Port11
3 D-Sub Port USB 2.0 Ports (USB_3_4) 12
4USB 3.0 Ports (USB3_1_2)
(AMD A88X (Bolton-D4)) 13 USB 3.0 Ports (USB3_3_4)
(ASMedia ASM1042A)
5 LAN RJ-45 Port** Clear CMOS Button14
6 Central / Bass (Orange) HDMI Port15
7 Rear Speaker (Black) 16 DVI-D Port
8 Line In (Light Blue) PS/2 Mouse/Keyboard Port17
9 Front Speaker (Lime)***
1011121314151617
3 4 75
6
2
1
9
8
4
English
* It is recommended to install the USB Keyboard/Mouse cable to USB 2.0 ports (USB_1_2
and USB_3 _4) instead of USB 3.0 ports.
** There are two LEDs on the L AN port. Please refer to the table below for the LAN port LED indica-
tions.
Activity / Link LED Speed LED
Status Description DescriptionStatus
Off OffNo Link 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
*** If you use a 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See
the table below for connection details in accordance with the type of speaker you use.
Audio Output
Channels
Front
Speaker
(No. 9)
Rear Speaker
(No. 7)
Central / Bass
(No. 6)
Line In or
Side Speaker
(No. 8)
2V -- -- --
4V V -- --
6V V V --
8V V V V
ACT/LINK LED
SPEED LED
LAN Port
To enable Multi-Streaming, you need to connect a front panel audio cable to
the front panel audio header. After restarting your computer, you will nd the
“Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable
playback multi-streaming”, and click “ok”. Choose “2CH”, “4CH”, “6CH”, or
“8CH” and then you are allowed to select “Realtek HDA Primary output” to
use the Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek
HDA Audio 2nd output” to use the front panel audio.
5
English
Fatal1ty FM2A88X+ Killer Series
1. Introduction
Thank you for purchasing ASRock motherboard, Fatal1ty FM2A88X+ Killer Series
a reliable motherboard produced under ASRock’s consistently stringent quality con-
trol. It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
This Quick Installation Guide contains introduction of the motherboard and step-by-
step installation guide. More detailed information of the motherboard can be found
in the user manual presented in the Support CD.
Because the motherboard specications and the BIOS software might
be updated, the content of this manual will be subject to change without
notice.Incaseanymodicationsofthismanualoccur,theupdatedver-
sion will be available on ASRock website without further notice. You may
nd thelatest VGAcards andCPU support listsonASRock website as
well. ASRock website http://www.asrock.com
If you require technical support related to this motherboard, please visit
ourwebsiteforspecicinformationaboutthemodelyouareusing.
www.asrock.com/support/index.asp
1.1 Package Contents
ASRock Series Motherboard (ATX Form Factor)Fatal1ty FM2A88X+ Killer
ASRock Series Quick Installation GuideFatal1ty FM2A88X+ Killer
ASRock Series Support CDFatal1ty FM2A88X+ Killer
2 x Serial ATA (SATA) Data Cables (Optional)
1 x I/O Panel Shield
ASRock Reminds You...
To get better performance in Windows
® 8 / 8 64-bit / 7 / 7 64-bit, it is
recommendedtosettheBIOSoptioninStorageCongurationtoAHCI
mode.
6
English
1.2 Specications
Platform • ATX Form Factor
• Premium Gold Capacitor design (100% Japan made
high quality conductive polymer capacitors)
A-Style • Purity SoundTM
Gaming
Armor
CPU Power
• Hi-Density Power Connector
VGA Card
• 15μGoldFingerinVGAPCIeSlot(PCIE2)
• SLI/CrossFireX Power Connector
Internet
• Qualcomm® Atheros® Killer
TM LAN
Audio
• Purity SoundTM
CPU • Supports Socket FM2+ 95W / FM2 100W processors
• Digi Power design
• 4 + 2 Power Phase design
Chipset • AMD A88X (Bolton-D4)
Memory • Dual Channel DDR3 Memory Technology
• 4 x DDR3 DIMM Slots
• Supports DDR3 2600+(OC)/2400(OC)/2133/1866/1600/
1333/1066 non-ECC, un-buffered memory (see
CAUTION 1)
* DDR3 2600+ is only supported with two DIMMs.
• Max. capacity of system memory: 64GB (see CAUTION
2)
• Supports Intel®ExtremeMemoryProle(XMP)1.3/1.2
• SupportsAMDMemoryProleTechnology(AMP)upto
AMP 2400
7
English
Fatal1ty FM2A88X+ Killer Series
Expan-
sion
Slot
• 1 x PCI Express 3.0 x16 Slot (PCIE2 @ x16 mode)
* PCIE 3.0 is only supported with FM2+ CPU. With FM2
CPU, it only supports PCIE 2.0.
• 1 x PCI Express 2.0 x16 Slot (PCIE4 @ p11-x4 mode)
• 2 x PCI Express 2.0 p11-x1 Slots
• 3 x PCI Slots
• Supports AMD Quad CrossFireXTM, CrossFireXTM and
Dual Graphics
Graphics • Integrated AMD Radeon HD 8000/7000 series graphics
in A-series APU
• DirectX 11.1, Pixel Shader 5.0 with FM2+ CPU. DirectX
11, Pixel Shader 5.0 with FM2 CPU.
• Max. shared memory 2GB
• Three graphics output options: D-Sub, DVI-D and HDMI
• Supports Triple Monitor
• Supports HDMI Technology with max. resolution up to
1920x1200 @ 60Hz
• Supports Dual-link DVI-D with max. resolution up to
2560x1600 @ 60Hz
• Supports D-Sub with max. resolution up to 1920x1200
@ 60Hz
• Supports Auto Lip Sync, Deep Color (12bpc), xvYCC
and HBR (High Bit Rate Audio) with HDMI Port
(Compliant HDMI monitor is required) (see CAUTION 3)
• Supports Blu-ray Stereoscopic 3D with HDMI Port
• Supports AMD Steady Video
TM 2.0: New video post
processing capability for automatic jitter reduction on
home/online video
• Supports HDCP with DVI-D and HDMI Ports
• Supports Full HD 1080p Blu-ray (BD) playback with
DVI-D and HDMI Ports
8
English
Audio • 7.1 CH HD Audio with Content Protection (Realtek
ALC1150 Audio Codec)
• Premium Blu-ray Audio support
• Supports Purity SoundTM
-115dBSNRDACwithDifferentialAmplier
- TI®NE5532PremiumHeadsetAmplier(Supportsup
to 600 ohm headsets)
- Direct Drive Technology
- EMI Shielding Cover
- PCB Isolate Shielding
• Supports DTS Connect
LAN • PCIE p12-x1 Gigabit LAN 10/100/1000 Mb/s
• Qualcomm® Atheros® Killer
TM E2200 Series
• Supports Wake-On-LAN
• SupportsEnergyEfcientEthernet802.3az
• Supports PXE
Rear
Panel I/O
• 1 x PS/2 Mouse/Keyboard Port
• 1 x D-Sub Port
• 1 x DVI-D Port
• 1 x HDMI Port
• 1 x Optical SPDIF Out Port
• 3 x USB 2.0 Ports
• 1 x Fatal1ty Mouse Port (USB 2.0)
• 2 x USB 3.0 Ports (AMD A88X (Bolton-D4))
• 2 x USB 3.0 Ports (ASMedia ASM1042A)
• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and
SPEED LED)
• 1 x Clear CMOS Switch with LED
• HD Audio Jacks: Rear Speaker / Central / Bass / Line in
/ Front Speaker / Microphone
9
English
Fatal1ty FM2A88X+ Killer Series
Storage • 8 x SATA3 6.0 Gb/s Connectors, support RAID (RAID
0, RAID 1, RAID 5 and RAID 10), NCQ, AHCI and Hot
Plug
Connec-
tor
• 1 x COM Port Header
• 1 x Chassis Intrusion Header
• 1 x TPM Header
• 1 x Power LED Header
• 2 x CPU Fan Connectors (1 x 4-pin, 1 x 3-pin)
• 3 x Chassis Fan Connectors (1 x 4-pin, 2 x 3-pin)
• 1 x Power Fan Connector (3-pin)
• 1 x 24 pin ATX Power Connector
• 1 x 8 pin 12V Power Connector (Hi-Density Power Con-
nector)
• 1 x SLI/XFire Power Connector
• 1 x Front Panel Audio Connector
• 3 x USB 2.0 Headers (Support 6 USB 2.0 ports)
• 1 x USB 3.0 Header by AMD A88X (Bolton-D4) (Sup-
ports 2 USB 3.0 ports)
BIOS
Feature
• 64Mb AMI UEFI Legal BIOS with GUI support
• Supports “Plug and Play”
• ACPI 1.1 Compliant wake up events
• Supports jumperfree
• SMBIOS 2.3.1 support
• DRAM, VDDP, VDDR Voltage multi-adjustment
Support
CD
• Drivers, Utilities, AntiVirus Software (Trial version),
Google Chrome Browser and Toolbar, Start8 (30 days
trial), XSplit, Killer Network Manager
Hardware
Monitor
• CPU temperature sensing
• Chassis temperature sensing
• CPU Fan Tachometer
• Chassis Fan Tachometer
• CPU/Chassis Quiet Fan
• CPU/Chassis Fan multi-speed control
• CASE OPEN detection
• Voltage monitoring: +12V, +5V, +3.3V, Vcore
10
English
OS • Microsoft® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8
64-bit / 7 32-bit / 7 64-bit
Certica-
tions
• FCC, CE, WHQL
• ErP/EuP Ready (ErP/EuP ready power supply is
required)
WARNING
Please realize that there is a certain risk involved with overclocking,
including adjusting the setting in the BIOS, applying Untied Overclocking
Technology, or using third-party overclocking tools. Overclocking may
affect your system’s stability, or even cause damage to the components
and devices of your system. It should be done at your own risk and
expense. We are not responsible for possible damage caused by
overclocking.
CAUTION!
1. Whether 2600/2400/2133/1866/1600MHz memory speed is
supported depends on the CPU you adopt. If you want to adopt
DDR3 2600/2400/2133/1866/1600MHz memory module on this
motherboard, please refer to the memory support list on our
website for the compatible memory modules.
ASRock website http://www.asrock.com
2. Due to the operating system limitation, the actual memory size
may be less than 4GB for the reservation for system usage un-
der Windows® 8 / 7. For Windows® 64-bit OS with 64-bit CPU,
there is no such limitation. You can use ASRock XFast RAM to
utilize the memory that Windows® cannot use.
3. xvYCC and Deep Color are only supported under Windows
® 8
64-bit / 8 / 7 64-bit / 7. Deep Color mode will be enabled only if
the display supports 12bpc in EDID. HBR is supported under-
Windows® 8 64-bit / 8 / 7 64-bit / 7.
* For detailed product information, please visit our website: http://www.asrock.com
11
English
Fatal1ty FM2A88X+ Killer Series
1.3 Unique Features
ASRock F-Stream
F-Stream is ASRock’s multi purpose software suite with a new
interface, more new features and improved utilities, including
XFast RAM, Dehumidier,Good Night LED, FAN-Tastic Tun-
ing, OC Tweaker and a whole lot more.
ASRock Instant Boot
ASRock Instant Boot allows you to turn on your PC in just a few
seconds, provides a much moreefcient way to save energy,
time, money, and improves system running speed for your sys-
tem. It leverages the S3 and S4 ACPI features which normally
enable the Sleep/Standby and Hibernation modes in Windows
®
toshortenbootuptime.BycallingS3andS4atspecictiming
during the shutdown and startup process, Instant Boot allows
you to enter your Windows
® desktop in a few seconds.
ASRock Instant Flash
 ASRockInstantFlashisaBIOSashutilityembeddedinFlash
ROM. This convenient BIOS update tool allows you to update
system BIOS withoutentering operating systems rst likeMS-
DOS or Windows®. With this utility, you can press the <F6> key
during the POST or the <F2> key to enter into the BIOS setup
menu to access ASRock Instant Flash. Just launch this tool and
savethe newBIOS leto yourUSB ashdrive,oppy diskor
hard drive, then you can update your BIOS only in a few clicks
withoutpreparing anadditional oppydisketteor othercompli-
cated ashutility. Please benoted that theUSB ash driveor
harddrivemustuseFAT32/16/12lesystem.
ASRock APP Charger
If you desire a faster, less restricted way of charging your
Apple devices, such as iPhone/iPad/iPod Touch, ASRock has
prepared a wonderful solution for you - ASRock APP Charger.
Simply install the APP Charger driver, it makes your iPhone
charge much quickly from your computer and up to 40% faster
than before. ASRock APP Charger allows you to quickly charge
many Apple devices simultaneously and even supports continu-
ous charging when your PC enters into Standby mode (S1),
12
English
Suspend to RAM (S3), hibernation mode (S4) or power off (S5).
With APP Charger driver installed, you can easily enjoy the mar-
velous charging experience.
ASRock XFast RAM
ASRock XFast RAM is included in F-Stream. It fully utilizes
the memory space that cannot be used under Windows
® 32-bit
operating systems. ASRock XFast RAM shortens the loading
timeofpreviously visited websites, making web surng faster
than ever. And it also boosts the speed of Adobe Photoshop 5
times faster. Another advantage of ASRock XFast RAM is that
it reduces the frequency of accessing your SSDs or HDDs in
order to extend their lifespan.
ASRock Crashless BIOS
ASRock Crashless BIOS allows users to update their BIOS
without fear of failing. If power loss occurs during the BIOS up-
date process,ASRock CrashlessBIOS willautomatically nish
the BIOS update procedure after regaining power. Please note
that BIOS les need to be placed in the root directory of your
USB disk. Only USB2.0 ports support this feature.
ASRock OMG (Online Management Guard)
Administrators are able to establish an internet curfew or restrict
internetaccessatspeciedtimesviaOMG.Youmayschedule
the starting and ending hours of internet access granted to other
users. In order to prevent users from bypassing OMG, guest
accounts without permission to modify the system time are re-
quired.
ASRock Internet Flash
ASRock Internet Flash searches for available UEFI firmware
updates from our servers. In other words, the system can auto-
detect thelatest UEFIfrom ourservers andashthem without
entering Windows® OS.
13
English
Fatal1ty FM2A88X+ Killer Series
ASRock UEFI System Browser
ASRock UEFI system browser is a useful tool included in
graphical UEFI. It can detect the devices and configurations
that users are currently using in their PC. With the UEFI system
browser,you caneasily examinethecurrentsystemcongura-
tion in UEFI setup.
ASRock UEFI Tech Service
Contact ASRock Tech Service by sending a support request
from the UEFI setup utility if you are having trouble with your
PC.
ASRock Dehumidier Function
Users may prevent motherboard damages due to dampness by
enabling “Dehumidier Function”. When enabling Dehumidier
Function, the computer will power on automatically to dehumidi-
fy the system after entering S4/S5 state.
ASRock Easy RAID Installer
ASRock Easy RAID Installer can help you to copy the RAID
driver from a support CD to your USB storage device. After
copying the RAID driver to your USB storage device, please
change “SATA Mode” to “RAID”, then you can start installing the
OS in RAID mode.
ASRock Easy Driver Installer
For users that don’t have an optical disk drive to install the
drivers from our support CD, Easy Driver Installer is a handy
tool in the UEFI that installs the LAN driver to your system via
an USB storage device, then downloads and installs the other
required drivers automatically.
ASRock Interactive UEFI
ASRock Interactive UEFI is a blend of system configuration
tools, cool sound effects and stunning visuals. The unprec-
edented UEFI provides a more attractive interface and brings a
lot more amusing.
14
English
ASRock Fast Boot
With ASRock’s exclusive Fast Boot technology, it takes less
than 1.5 seconds to logon to Windows
® 8 from a cold boot. No
more waiting! The speedy boot will completely change your user
experience and behavior.
ASRock X-Boost
Brilliantly designed for combo overclocking, ASRock X-Boost
Technology is able to unleash the hidden power of your CPUs.
Simply press “X” when turning on the PC, X-Boost will automati-
cally overclock the relative components to get up to 15.77%
performance boost! With the smart X-Boost, overclocking CPU
can become a near one-button process.
ASRock Restart to UEFI
Windows® 8 brings the ultimate boot up experience. The light-
ning boot up speed makes it hard to access the UEFI setup. AS-
Rock Restart to UEFI technology is designed for those requiring
frequent UEFI access. It is included in ASRock’s exclusive all-in-
one F-Stream tuning program that allows users to easily enter
the UEFI automatically when turning on the PC next time. Just
simply enable this function; the PC will be assured to access the
UEFI directly in the very beginning.
ASRock USB Key
In a world where time is money, why waste precious time
everyday typing usernames to log in to Windows? Why should
we even bother memorizing those foot long passwords? Just
plug in the USB Key and let your computer log in to windows
automatically!
ASRock Key Master
What good is a weapon if you are unable to wield it profi-
ciently? Key Master enhances your mouse and keyboard with
customizable macros, sniper modes, scroll speed, key repeat
rates and repeat delay, turning your boring old keyboard and-
mouse into lethal weapons.
ASRock FAN-Tastic Tuning
ASRock FAN-Tastic Tuning is included in F-Stream. Congure
up to ve different fan speeds using the graph. The fans will
automatically shift to the next speed level when the assigned
temperature is met.
15
English
Fatal1ty FM2A88X+ Killer Series
2. Installation
This is an ATX form factor motherboard. Before you install the motherboard, study
thecongurationofyourchassistoensurethatthemotherboardtsintoit.
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
1. Unplug the power cord from the wall socket before touching any
component.
2. To avoid damaging the motherboard components due to static elec-
tricity, NEVER place your motherboard directly on the carpet or the
like. Also remember to use a grounded wrist strap or touch a safety
grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-
static pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the mother-
board to the chassis, please do not over-tighten the screws! Doing
so may damage the motherboard.
16
English
2.1 CPU Installation
Step 1. Unlock the socket by lifting the lever up
to a 90o angle.
Step 2. Position the CPU directly above the
socket such that the CPU corner with
the golden triangle matches the socket
corner with a small triangle.
Step 3. Carefully insert the CPU into the
 socketuntilittsinplace.
TheCPUtsonlyinonecorrect
orientation. DO NOT force the CPU
into the socket to avoid bending of
the pins.
Step 4. When the CPU is in place, press it
rmlyonthesocketwhileyoupush 
down the socket lever to secure the
CPU. The lever clicks on the side tab
to indicate that it is locked.
17
English
Fatal1ty FM2A88X+ Killer Series
2.2 Installation of CPU Fan and Heatsink
After you install the CPU into this motherboard, it is necessary to install a
larger heatsink and cooling fan to dissipate heat. You also need to spray
thermal grease between the CPU and the heatsink to improve heat dis-
sipation. Make sure that the CPU and the heatsink are securely fastened
and in good contact with each other. Then connect the CPU fan to the
CPU FAN connector (CPU_FAN1 and CPU_FAN2, see Page 1, No. 3, 4).
For proper installation, please kindly refer to the instruction manuals of
the CPU fan and the heatsink.
18
English
2.3 Installation of Memory Modules (DIMM)
This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM
slots, and supports Dual Channel Memory Technology.
DualChannelMemoryConguration
The DIMM only ts in one correct orientation. It will cause permanent dam-
age to the motherboard and the DIMM if you force the DIMM into the slot at
incorrect orientation.
Priority DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2
1Populated Populated
2 Populated Populated
3Populated Populated Populated Populated
1. For dual channel conguration, you always need to install identical (the
same brand, speed, size and chip-type) DDR3 DIMM pairs.
2. It is unable to activate Dual Channel Memory Technology with only one or
three memory module installed.
3. It is not allowed to install a DDR or DDR2 memory module into a DDR3
slot; otherwise, this motherboard and DIMM may be damaged.
4. If you adopt DDR3 2600/2400/2133/1866/1600 memory modules on this
motherboard, it is recommended to install them on DDR3_A2 and DDR3_
B2 slots.
19
English
Fatal1ty FM2A88X+ Killer Series
1
2
3
20
English
2.4 Expansion Slots (PCI and PCI Express Slots)
There are 3 PCI slots and 4 PCI Express slots on this motherboard.
PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
PCIE Slots:
PCIE1 / PCIE3 (PCIe 2.0 p24-x1 slot) is used for PCI Express cards with p24-x1
lane width cards.
PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graph-
ics cards.
PCIE4 (PCIe 2.0 x16 slot) is used for PCI Express p24-x4 lane width graph-
ics cards.
PCIe Slot Congurations
For a better thermal environment, please connect a chassis fan to the moth-
erboard’s chassis fan connector (CHA_FAN1, CHA_FAN2 or CHA_FAN3)
when using multiple graphics cards.
Before installing an expansion card, please make sure that the power supply
is switched off or the power cord is unplugged. Please read the documenta-
tion of the expansion card and make necessary hardware settings for the card
before you start the installation.
PCIE2 PCIE4
Single Graphics Card x16 N/A
Two Graphics Cards in
CrossFireXTM Mode x16 x4
21
English
Fatal1ty FM2A88X+ Killer Series
2.5 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.
Jumper Setting Description
Clear CMOS Jumper
(CLRCMOS1)
(see p.1, No. 27)
Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the
system parameters to default setup, please turn off the computer and unplug
the power cord from the power supply. After waiting for 15 seconds, use a
jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However,
please do not clear the CMOS right after you update the BIOS. If you need
tocleartheCMOSwhenyoujustnishupdatingtheBIOS,youmustbootup
thesystemrst,andthenshutitdownbeforeyoudotheclear-CMOSaction.
Pleasebenotedthatthepassword,date,time,userdefaultproleandMAC
address will be cleared only if the CMOS battery is removed.
Clear CMOSDefault
1. If you clear the CMOS, the case open may be detected. Please adjust
the BIOS option “Clear Status” to clear the record of previous chassis
intrusion status.
2. The Clear CMOS Button has the same function as the Clear CMOS
jumper.
22
English
Serial ATA3 Connectors These eight Serial ATA3
(SATA3_1_2: see p.1, No. 10) (SATA3) connectors support
(SATA3_3_4: see p.1, No. 11) SATA data cables for internal
(SATA3_5_6: see p.1, No. 12) storage devices. The current
(SATA3_7_8: see p.1, No. 13) SATA3 interface allows up to
6.0 Gb/s data transfer rate.
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
USB 2.0 Headers Besides four default USB 2.0
(9-pin USB_5_6) ports on the I/O panel, there
(see p.1 No. 22) are three USB 2.0 headers on
(9-pin USB_7_8) this motherboard. Each USB 2.0
(see p.1 No. 21) header can support two USB
(9-pin USB_9_10) 2.0 ports.
(see p.1 No. 20)
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
U RSB_PW
1
USB 3.0 Header Besides four default USB 3.0
(19-pin USB3_5_6) ports on the I/O panel, there is
(see p.1 No. 8) one USB 3.0 header on this
motherboard. This USB 3.0
header can support two USB 3.0
ports.
1
IntA_PB_D+
Dummy
IntA_PB_D-
GND
IntA_PB_SSTX+
GND
IntA_PB_SSTX-
IntA_PB_SSRX+
IntA_PB_SSRX-
VbusVbus
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
SATA3_1_2SATA3_5_6 SATA3_3_4SATA3_7_8
23
English
Fatal1ty FM2A88X+ Killer Series
Front Panel Audio Header This is an interface for the front
(9-pin HD_AUDIO1) panel audio cable that allows
(see p.1 No. 26) convenient connection and
control of audio devices.
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
System Panel Header This header accommodates
(9-pin PANEL1) several system front panel
(see p.1 No. 14) functions.
GND
R #E SET
PWRBT N#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
 1.HighDenitionAudiosupportsJackSensing,butthepanelwireon
the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
E. To activate the front mic.
For Windows
® 8 / 8 64-bit / 7 / 7 64-bit OS:
Go to the “FrontMic” Tab in the Realtek Control panel. Adjust
“Recording Volume”.
Connect the power switch, reset switch and system status indicator
on the chassis to this header according to the pin assignments below.
Note the positive and negative pins before connecting the cables.
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may con-
gurethewaytoturnoffyoursystemusingthepowerswitch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to per-
form a normal restart.
24
English
Power LED Header Please connect the chassis
(3-pin PLED1) power LED to this header to
(see p.1 No. 18) indicate system power status.
The LED is on when the system
is operating. The LED keeps
blinking in S1 state. The LED is
off in S3/S4 state or S5 state
(power off).
Chassis Speaker Header Please connect the chassis
(4-pin SPEAKER 1) speaker to this header.
(see p.1 No. 16)
1
+5V
DUMM Y
DUMM Y
SPEAKER
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The
LED is on when the system is operating. The LED keeps blinking
when the sys-tem is in S1 sleep state. The LED is off when the system
is in S3/S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The
LED is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module
mainly consists of power switch, reset switch, power LED, hard drive
activity LED, speaker and etc. When connecting your chassis front
panel module to this header, make sure the wire assignments and the
pin assign-ments are matched correctly.
Chassis and Power Fan
Please connect the fan cable
Connectors to the fan connector and
(4-pin CHA_FAN1) match the black wire to the
(see p.1 No. 17) ground pin.
(4-pin CHA_FAN2)
(see p.1 No. 15)
(4-pin CHA_FAN3)
(see p.1 No. 9)
(3-pin PWR_FAN1)
(see p.1 No. 2)
1
PLED+
PLED+
PLED-
GND
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTROL
25
English
Fatal1ty FM2A88X+ Killer Series
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.
ATX Power Connector Please connect an ATX power
(24-pin ATXPWR1) supply to this connector.
(see p.1 No. 7)
12
1
Though this motherboard provides 24-pin ATX power connector,
it can still work if you adopt a traditional 20-pin ATX power supply.
To use the 20-pin ATX power supply, please plug your power
supply along with Pin 1 and Pin 13.
20-Pin ATX Power Supply Installation
Pin 1-3 Connected
3-Pin Fan Installation
24
13
CPU Fan Connector Please connect the CPU fan
(4-pin CPU_FAN1) cable to the connector and
(see p.1 No. 3) match the black wire to the
ground pin.
(3-pin CPU_FAN2)
(see p.1, No. 4)
GND
+ 12V
CPU_
FAN_SPEED
FAN_SPEED_CONT ROL
1 2 3 4
ATX 12V Power Connector Please connect an ATX 12V
(8-pin ATX12V1) power supply to this connector.
(see p.1 No. 1)
Though this motherboard provides 8-pin ATX 12V power connector, it can still work
if you adopt a traditional 4-pin ATX 12V power supply. To use the
4-pin ATX power supply, please plug your power supply along with
Pin 1 and Pin 5.
4-Pin ATX 12V Power Supply Installation
GND
+12V
CPU_FAN_SPEED
8 5
4 1
12
1
24
13
26
English
Serial port Header This COM1 header supports a
(9-pin COM1) serial port module.
(see p.1 No. 25)
Chassis Intrusion Header This motherboard supports
(2-pin CI1) CASE OPEN detection feature
(see p.1, No. 19) that detects if the chassis cover
has been removed. This feature
requires a chassis with chassis
intrusion detection design.
1
Signal
GND
TPM Header This connector supports
(17-pin TPMS1) Trusted Platform Module (TPM)
(see p.1, No. 23) system, which can securely
 storekeys,digitalcerticates,
passwords, and data. A TPM
system also helps enhance
network security, protects
digital identities, and ensures
platform integrity.
SLI/XFIRE Power Connector
(4-pin SLI/XFIRE_PWR1)
(see p.1, No. 24)
1
LF RAME # _L
CK_ 33M_TPM
TPM_RST #
LAD3_L
+3V
LAD0_L
+3VSB
GNDF_CL KRUN #
SERIRQ#
S_PWRDWN#
GND
LAD1_L
LAD2_L
SMB_DA
TA_ MAIN
SMB_CLK_ MAIN
GND
Please connect this connector
with a hard disk power
connector when two graphics
cards are installed on this
motherboard.
27
English
Fatal1ty FM2A88X+ Killer Series
3. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up
the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST)
to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you
wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl>
+ <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS
Setup program is designed to be user-friendly. It is a menu-driven program, which
allows you to scroll through its various sub-menus and to select among the prede-
termined choices. For the detailed information about BIOS Setup, please refer to the
UserManual(PDFle)containedintheSupportCD.
4. Software Support CD information
This motherboard supports various Microsoft
® Windows® operating systems: 8.1 32-
bit / 8.1 64-bit / 8 32-bit / 8 64-bit / 7 32-bit / 7 64-bit. The Support CD that came with
the motherboard contains necessary drivers and useful utilities that will enhance
motherboard features. To begin using the Support CD, insert the CD into your CD-
ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in
your computer. If the Main Menu does not appear automatically, locate and double-
clickonthele“ASRSETUP.EXE”fromtheBINfolderintheSupportCDtodisplay
the menus.
28
Deutsch
1. Einführung
Wir danken Ihnen für den Kauf des ASRock Fatal1ty FM2A88X+ Killer Series
Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen
Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung
undrobustesDesign,gemäßderVerpichtungvonASRockzuQualitätund
Halbarkeit. Diese Schnellinstallationsanleitung führt in das Motherboard und die
schrittweiseInstallationein.DetailsüberdasMotherboardndenSieinderBedien-
ungsanleitung auf der Support-CD.
DasichMotherboard-SpezikationenundBIOS-Softwareverändern 
können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert
werden. Für den Fall, dass sich Änderungen an diesem Handbuch
ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere
 Ankündigung,verfügbarsein.DieneuestenGrakkartenundunterstützten
CPUs sind auch auf der ASRock-Website aufgelistet.
ASRock-Website: http://www.asrock.com
WennSietechnischeUnterstützungzuIhremMotherboardoderspezische
Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere
Webseite:
www.asrock.com/support/index.asp
1.1 Kartoninhalt
ASRock Motherboard (ATX-Formfaktor)Fatal1ty FM2A88X+ Killer Series
ASRock SchnellinstallationsanleitungFatal1ty FM2A88X+ Killer Series
ASRock Support-CDFatal1ty FM2A88X+ Killer Series
Zwei Serial ATA (SATA) -Datenkabel (optional)
Ein I/O Shield
ASRock erinnert...
Zur besseren Leistung unter Windows
® 8 / 8 64 Bit / 7 / 7 64 Bit emp-
fehlen wir, die Speicherkonfiguration im BIOS auf den AHCI-Modus
einzustellen.HinweisezudenBIOS-Einstellungen nden Sie in derBe-
dienungsanleitung auf der mitgelieferten CD.
29
Deutsch
Fatal1ty FM2A88X+ Killer Series
1.2 Spezikationen
Platform • ATX-Formfaktor
• Premium Gold-Kondensatordesign (100 % in
Japan gefertigt, hochqualitative leitfähige Polymer-
Kondensatoren)
A-Stil • Purity SoundTM
Gaming
Armor
CPU-Power
• Hi-Density-Netzanschluss
VGA-Karte
• 15μGoldFingerinVGA-PCIe-Steckplatz(PCIE2)
• SLI/XFire-Netzanschluss
Internet
• Qualcomm® Atheros® Killer
TM LAN
Audio
• Purity SoundTM
CPU • Unterstützt Prozessoren für Sockel FM2+ (95 W) / FM2
(100 W)
• Digipower-Design
• 4 + 2-Stromphasendesign
Chipsatz • AMD A88X (Bolton-D4)
Speicher • Unterstützung von Dual-Kanal-Speichertechnologie
• 4 x Steckplätze für DDR3
• Unterstützt DDR3 2600+(OC)/2400
(OC)/2133/1866/1600/1333/1066 non-ECC,
ungepufferter Speicher
* DDR3 2600+ wird nur mit zwei DIMMs unterstützt.
• Max. Kapazität des Systemspeichers: 64GB
• Unterstützt Intel®ExtremeMemoryProle(XMP)1.3/1.2
• UnterstütztAMDsMemoryProleTechnology(AMP)
bis AMP 2400
30
Deutsch
Erweit-
erungs-
steckplä-
tze
• 1 x PCI Express 3.0 x16-Steckplätze
* PCIE 3.0 wird nur mit FM2+-Prozessor unterstützt.FM2-
Prozessor unterstützt nur PCIE 2.0.
• 1 x PCI Express 2.0 x16-Steckplatz (PCIE4: x4-Modus)
• 2 x PCI Express 2.0 x1-Steckplätze
• 3 x PCI -Steckplätze
• Unterstützt AMD Quad CrossFireXTM , CrossFireXTM und
dualeGrakkarten
Onboard-
VGA
• IntegrierteGrakkartederAMDRadeonHD
8000/7000-Serie in APU der A-Serie
• DirectX 11.1, Pixel Shader 5.0 mit FM2+-Prozessor.
DirectX 11, Pixel Shader 5.0 mit FM2-Prozessor.
• Maximal gemeinsam genutzter Speicher 2GB
• Drei VGA-Ausgangsoptionen: D-Sub, DVI-D sowie
HDMI Unterstützt drei Monitore
• UnterstütztHDMImiteinermaximalenAuösungvon
• 1920 x 1200 bei 60 Hz
• Unterstützt Dual-link DVI-D mit einer maximalen
Auösungvon2560x1600bei60Hz
• UnterstütztD-SubmiteinermaximalenAuösungvon
1920 x 1200 bei 60 Hz
• Unterstützt Auto Lip Sync, Deep Color (12bpc), xvYCC
und HBR (High Bit Rate-Audio) mit HDMI (kompatibler
• HDMI-Bildschirm erforderlich)
• Unterstützt stereoskopisches 3D per Blu-ray mit HDMI
• Unterstützt AMD Steady Video
TM 2.0: Neuartige
Funktion der Videonachbearbeitung für automatische
Reduzierung von Bildschwankungen bei Heim-/Online-
Videos
• Unterstützt HDCP mit DVI-D- und HDMI-Ports
• Unterstutzt 1080p Blu-ray (BD)-Wiedergabe mit DVI-D-
und HDMI-Ports
31
Deutsch
Fatal1ty FM2A88X+ Killer Series
Audio • 7.1-Kanal-HD-Audio mit Inhaltsschutz (Realtek
ALC1150-Audiocodec)
• Erstklassige Blu-ray-Audiounterstützung
• Unterstützt Purity SoundTM
- 115-dB-SRV-DAC mit Differentialverstärker TI®
NE5532 (unterstützt erstklassigen Headset-Verstärker
mit bis zu 600 Ohm)
- Direct Drive Technology
- Abdeckung mit EMV-Abschirmung
- PCB-isolierte Abschirmung
• Unterstützt DTS Connect
LAN • PCIE p35-x1 Gigabit LAN 10/100/1000 Mb/s
• Qualcomm® Atheros® Killer
TM E2200 Series
• Unterstützt Wake-On-LAN
• UnterstütztenergieefzientesEthernet802.3az
• Unterstützt PXE
E/A-An-
schlüsse
an der
Rückseite
• 1 x PS/2-Maus/Tastaturanschluss
• 1 x D-Sub port
• 1 x DVI-D port
• 1 x HDMI port
• 1 x optischer SPDIF-Ausgang
• 3 x USB 2.0-Ports
• 1 x Fatal1ty-Mausanschluss (USB 2.0)
• 2 x Standard-USB 3.0-Anschlüsse (AMD A88X
(Bolton-D4))
• 2 x Standard-USB 3.0-Anschlüsse (ASMedia
ASM1042A)
• 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und
SPEED LED)
• 1 x CMOS löschen-Schalter
• HD Audiobuchse: Lautsprecher hinten / Mitte/Bass /
Audioeingang / Lautsprecher vorne / Mikrofon
Speicher • 8 x SATA 3-Anschluss mit 6,0 Gb/s, unterstützt RAID-
(RAID 0, RAID 1, RAID 5 und RAID 10), NCQ-, AHCI-
und „Hot Plugging“-Funktionen
32
Deutsch
An-
schlüsse
• 1 x COM-Anschluss-Header
• 1 x Verteiler für Gehäuseeindringversuche
• 1 x TPM-Stiftleiste
• 1 x Betriebs-LED-Header
• 2 x CPUlüfter-Anschluss (1 x 4-pin, 1 x 3-pin)
• 3 x Gehäuselüfter-Anschluss (1 x 4-pin, 2 x 3-pin)
• 1 x Stromlüfter-Anschluss (3-pin)
• 1 x 24-pin ATX-Netz-Header
• 1 x 8-pin anschluss für 12V-ATX-Netzteil (hochdichter
Netzanschluss)
• 1 x SLI/XFire-Netzanschluss
• 1 x Anschluss für Audio auf der Gehäusevorderseite
• 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher
USB 2.0-Anschlüsse)
• 1 x USB 3.0-Anschlüsse über AMD A88X (Bolton-D4)
(Unterstützung 2 zusätzlicher USB 3.0-Anschlüsse)
BIOS • 64Mb AMIs Legal BIOS UEFI mit GUI-Unterstützung
• Unterstützung für “Plug and Play”
• ACPI 1.1-Weckfunktionen
• JumperFree-Modus
• SMBIOS 2.3.1
• DRAM, VDDP, VDDR Stromspannung Multianpassung
Support-
CD
• Pilotes, utilitaires, logiciel anti-virus (Version d’essai),
Google ChromeBrowser et Toolbar, Start8 (30 jours
d’évaluation), Xsplit, Killer Network Manager
Hardware
Monitor
• CPU-Temperatursensor
• Motherboardtemperaturerkennung
• Drehzahlmessung für CPUlüfter
• Drehzahlmessung für Gehäuselüfter
• Geräuscharmer CPU-/Gehäuselüfter
• MehrstugeGeschwindigkeitsteuerungfürCPU
• GEHÄUSE OFFEN-Erkennung
• Gehäuselüfter Spannungsüberwachung: +12V, +5V,
+3.3V, Vcore
33
Deutsch
Fatal1ty FM2A88X+ Killer Series
Betriebs-
systeme
• Microsoft® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit /
• 8 64-bit / 7 32-bit / 7 64-bit
Zerti-
zierungen
• FCC, CE, WHQL
• Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP
requise)
* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website:
http://www.asrock.com
34
Deutsch
1.3 Einstellung der Jumper
Die Abbildung verdeutlicht, wie Jumper
gesetzt werden. Werden Pins durch
Jumperkappen verdeckt, ist der Jumper
“Gebrückt”. Werden keine Pins durch
Jumperkappen verdeckt, ist der Jumper
“Offen”. Die Abbildung zeigt einen 3-Pin
Jumper dessen Pin1 und Pin2 “Ge-
brückt”sind,bzw. es bendet sicheine
Jumper-Kappe auf diesen beiden Pins.
Jumper Einstellun Beschreibung
CMOS löschen
(CLRCMOS1, 3-Pin jumper)
(siehe S.1, No. 27)
Hinweis:
CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum
Löschen und Zurücksetzen der Systemparameter auf die Standardeinrichtung
schalten Sie den Computer bitte aus und trennen das Netzkabel von der
Stromversorgung. Warten Sie 15 Sekunden, schließen Sie dann Pin2 und
Pin3 am CLRCMOS1 über einen Jumper fünf Sekunden lang kurz. Sie
sollten das CMOS allerdings nicht direkt nach der BIOS-Aktualisierung
löschen. Wenn Sie das CMOS nach Abschluss der BIOS-Aktualisierung
löschen müssen, fahren Sie zuerst das System hoch. Fahren Sie es dann
vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort,
Datum,Uhrzeit,benutzerdeniertesProl undMAC-Adressenurgelöscht
werden, wenn die CMOS-Batterie entfernt wird.
CMOS
löschen
Default-
Einstellung
1. Durch Löschen des CMOS kann erkannt werden, wenn das
Gehäuseoffen ist. Bitte stellen Sie zum Löschen der Aufzeichnung
des vorherigenGehäuseindringungsstatus die BIOS-Option “Status
leeren” ein.
2. Der CMOS-löschen-Schalter hat dieselbe Funktion wie der
CMOS-löschen-Jumper.
35
Deutsch
Fatal1ty FM2A88X+ Killer Series
USB 2.0-Header Zusätzlich zu den vier
(9-pol. USB_5_6) üblichen USB 2.0-Ports an den
(siehe S.1 - No. 22)  I/O-Anschlüssenbendensich
(9-pol. USB_7_8) drei USB 2.0-
(siehe S.1 - No. 21) Anschlussleisten am
(9-pol. USB_9_10) Motherboard. Pro USB 2.0-
(siehe S.1 - No. 20) Anschlussleiste werden zwei
USB 2.0-Ports unterstützt.
Seriell-ATA3-Anschlüsse Diese acht Serial ATA3-
(SATA3_1_2: siehe S.1 - No. 10) (SATA3-)Verbínder
(SATA3_3_4: siehe S.1 - No. 11) unterstützten SATA-Datenkabel
(SATA3_5_6: siehe S.1 - No. 12) für interne
(SATA3_7_8: siehe S.1 - No. 13) Massenspeichergeräte. Die
aktuelle SATA3- Schnittstelle
ermöglicht eine
Datenübertragungsrate bis
6,0 Gb/s.
1.4 Anschlüsse
Anschlussleisten sind KEINE Jumper. Setzen Sie KEINE Jumperkappen
auf die Pins der Anschlussleisten. Wenn Sie die Jumperkappen auf die
Anschlüsse setzen, wird das Motherboard permanent beschädigt!
Anschluss Beschreibung
USB 3.0-Header Neben vier Standard-USB
(19-pol. USB3_5_6) 3.0-Ports am E/A-Panel
(siehe S.1 - No. 8)  bendetsicheinUSB3.0-
Header an diesem
Motherboard. Dieser USB 3.0-
Header kann zwei USB 3.0-
Ports unterstützen.
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
U RSB_PW
1
1
IntA_PB_D+
Dummy
IntA_PB_D-
GND
IntA_PB_SSTX+
GND
IntA_PB_SSTX-
IntA_PB_SSRX+
IntA_PB_SSRX-
VbusVbus
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
SATA3_1_2SATA3_5_6 SATA3_3_4SATA3_7_8
36
Deutsch
Anschluss für Audio auf Dieses Interface zu einem
der Gehäusevorderseite Audio-Panel auf der Vorder
(9-Pin HD_AUDIO1) seite Ihres Gehäuses,
(siehe S.1 - No. 26) ermöglicht Ihnen eine bequeme
Anschlussmöglichkeit und
Kontrolle über Audio-Geräte.
1.HighDenitionAudiounterstütztJackSensing(automatischeErkennung 
falsch angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung
am Gehäuse HDA unterstützen muss, um richtig zu funktionieren.
Beachten Sie bei der Installation im System die Anweisungen in unserem
Handbuch und im Gehäusehandbuch.
2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie
nachstehend beschrieben an der Front-Audioanschlussleiste:
A. Schließen Sie Mic_IN (MIC) an MIC2_L an.
B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) an OUT2_L an.
C. Schließen Sie Ground (GND) an Ground (GND) an.
D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese
Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden.
E. So aktivieren Sie das Mikrofon an der Vorderseite.
Bei den Betriebssystemen Windows
® 8 / 8 64 Bit / 7 / 7 64 Bit:
Wählen Sie im Realtek-Bedienfeld die „FrontMic“ (Vorderes Mikrofon)-
Registerkarte. Passen Sie die „Recording Volume“ (Aufnahmelautstärke)
an.
System Panel-Header Dieser Header unterstützt
(9-pin PANEL1) mehrere Funktion der
(siehe S.1 - No. 14) Systemvorderseite.
Schließen Sie die Ein-/Austaste, die Reset-Taste und die
Systemstatusanzeige am Gehäuse an diesen Header an; befolgen Sie
dabei die nachstehenden Hinweise zur Pinbelegung. Beachten Sie die
positiven und negativen Pins, bevor Sie die Kabel anschließen.
37
Deutsch
Fatal1ty FM2A88X+ Killer Series
PWRBTN (Ein-/Ausschalter):
Zum Anschließen des Ein-/Ausschalters an der Frontblende des Gehäu
  ses.Siekönnenkongurieren,wiedasSystemmitHilfedes
Ein-/Ausschalters ausgeschaltet werden können soll.
RESET (Reset-Taste):
Zum Anschließen der Reset-Taste an der Frontblende des Gehäuses.
Mit der Reset-Taste können Sie den Computer im Falle eines Absturzes
neu starten.
PLED (Systembetriebs-LED):
Zum Anschließen der Betriebsstatusanzeige an der Frontblende des
Gehäuses. Die LED leuchtet, wenn das System in Betrieb ist. Die LED
  blinkt,wennsichdasSystemimRuhezustandS3bendet.DieLED
  schaltetsichaus,wennsichdasSystemindenModiS4bendet
oder ausgeschaltet ist (S5).
HDLED (Festplattenaktivitäts-LED):
Zum Anschließen der Festplattenaktivitäts-LED an der Frontblende des
Gehäuses. Die LED leuchtet, wenn die Festplatte Daten liest oder
schreibt.
Das Design der Frontblende kann je nach Gehäuse variiere. Ein
Frontblendenmodul besteht hauptsächlich aus einer Ein-/Austaste, einer
Reset-Taste, einer Betriebs-LED, einer Festplattenaktivitäts-LED,
Lautsprechern, etc. Stellen Sie beim Anschließen des
Frontblendenmoduls Ihres Gehäuses an diesem Header sicher, dass die
Kabel- und Pinbelegung korrekt übereinstimmen.
Gehäuselautsprecher-Header Schließen Sie den
(4-pin SPEAKER1) Gehäuselautsprecher an
(siehe S.1 - No. 16) diesen Header an.
Betriebs-LED-Header Bitte schließen Sie die
(3-pin PLED1) Betriebs-LED des Gehäuses
(siehe S.1 - No. 18) zur Anzeige des
Systembetriebsstatus an
diesem Header an. Die LED
leuchtet, wenn das System in
Betrieb ist. Die LED blinkt im
S3-Zustand. Im S4- oder
S5-Zustand (ausgeschaltet)
leuchtet die LED nicht.
38
Deutsch
CPU-Lüfteranschluss Verbinden Sie das CPU -
(4-pin CPU_FAN1) Lüfterkabel mit diesem
(siehe S.1 - No. 3) Anschluss und passen Sie den
schwarzen Draht dem
Erdungsstift an.
Pins 1–3 anschließen
Lüfter mit dreipoligem Anschluss installieren
Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss
(Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss
angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn
Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses
Motherboards anschließen möchten, verbinden Sie ihn bitte mit den
Pins 1 – 3.
(3-pin CPU_FAN2)
(siehe S.1 - No. 4)
ATX-Netz-Header Verbinden Sie die ATX-
(24-pin ATXPWR1) Stromversorgung mit diesem
(siehe S.1 - No. 7) Header.
Obwohl dieses Motherboard einen 24-pol. ATX-
Stromanschluss bietet, kann es auch mit einem
  modiziertentraditionellen20-pol.ATX-Netzteil
verwendet werden. Um ein 20-pol. ATX-Netzteil zu
verwenden, stecken Sie den Stecker mit Pin 1 und
Pin 13 ein.
12
1
24
13
12
1
24
13
Gehäuse- und Verbinden Sie die Lüfterkabel
Stromlüfteranschlüsse mit den Lüfteranschlüssen,
(4-pin CHA_FAN1) wobei der schwarze Draht an
(siehe S.1 - No. 17) den Schutzleiterstift
angeschlossenwird.
(3-pin CHA_FAN2)
(siehe S.1 - No. 15)
(3-pin CHA_FAN3)
(siehe S.1 - No. 9)
(3-pin PWR_FAN1)
(siehe S.1 - No. 2)
GND
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTROL
1 2 3 4
GND
+ 12V
CPU_
FAN_SPEED
FAN_SPEED_CONT ROL
GND
+12V
CPU_FAN_SPEED
39
Deutsch
Fatal1ty FM2A88X+ Killer Series
Installation der 4-Pin ATX 12V Energieversorgung
Obwohl diese Hauptplatine 8-Pin ATX 12V Stromanschluss zur
Verfügung stellt, kann sie noch arbeiten, wenn Sie einen
traditionellen 4-Pin ATX 12V Energieversorgung adoptieren. Um die
4-Pin ATX Energieversorgung zu verwenden, stecken Sie bitte Ihre
Energieversorgung zusammen mit dem Pin 1 und Pin 5 ein.
COM-Anschluss-Header Dieser COM-Anschluss-
(9-pin COM1) Header wird verwendet, um
(siehe S.1 - No. 25) ein COM-Anschlussmodul zu
unterstützen.
SLI/XFIRENetzanschluss
(4-polig, SLI/XFIRE_PWR1)
(siehe S.1 - No. 24)
Verteiler für Gehäuseeindringversuche Dieses Motherboard unterstützt
(2-pin CI1) die GEHÄUSE OFFEN-
(siehe S.1 - No. 19) Erkennungsfunktion,die
feststellt, ob dieGehäuseab-
deckung entferntwurde. Für
diese Funktion istein Ge-
häuse erforderlich, dasmit ei-
nem Design zur Erkennung
von Gehäuseeindringver-
suchenausgestattet ist.
ATX 12V Anschluss Bitte schließen Sie an diesen
(8-pin ATX12V1) Anschluss die ATX 12V
(siehe S.1 - No. 1) Stromversorgung an.
8 5
4 1
CC TS # 1
RR TS # 1
D DS R# 1
D DT R # 1
RRXD1
GND
TTXD 1
D DC D # 1
1
RR I# 1
1
Signal
GND
Bitte verbinden Sie diese
Anschluss mit einem
Festplattennetzanschluss,
wennzweiGrakkartenan
diesem Motherboard installiert
sind.
41
Deutsch
Fatal1ty FM2A88X+ Killer Series
2. BIOS-Information
Das Flash Memory dieses Motherboards speichert das Setup-Utility. Drücken Sie
<F2> oder <Del> während des POST (Power-On-Self-Test) um ins Setup zu gelan-
gen, ansonsten werden die Testroutinen weiter abgearbeitet. Wenn Sie ins Setup
gelangen wollen, nachdem der POST durchgeführt wurde, müssen Sie das System
über die Tastenkombination <Ctrl> + <Alt> + <Delete> oder den Reset-Knopf auf
der Gehäusevorderseite, neu starten. Natürlich können Sie einen Neustart auch
durchführen, indem Sie das System kurz ab- und danach wieder anschalten.
Das Setup-Programm ist für eine bequeme Bedienung entwickelt worden. Es ist ein
menügesteuertes Programm, in dem Sie durch unterschiedliche Untermenüs scrol-
len und die vorab festgelegten Optionen auswählen können. Für detaillierte Infor-
mationen zum BIOS-Setup, siehe bitte das Benutzerhandbuch (PDF Datei) auf der
Support CD.
3. Software Support CD information
Dieses Motherboard unterstützt eine Reiche von Microsoft
® Windows® Betriebssys-
temen: 8 / 8 64-Bit / 7 / 7 64-Bit. Die Ihrem Motherboard beigefügte Support-CD en-
thält hilfreiche Software, Treiber und Hilfsprogramme, mit denen Sie die Funktionen
Ihres Motherboards verbessern können Legen Sie die Support-CD zunächst in Ihr
CD-ROM-Laufwerk ein. Der Willkommensbildschirm mit den Installationsmenüs der
CD wird automatisch aufgerufen, wenn Sie die “Autorun”-Funktion Ihres Systems
aktiviert haben.
Erscheint der Wilkommensbildschirm nicht, so “doppelklicken” Sie bitte auf das File
ASSETUP.EXE im BIN-Verzeichnis der Support-CD, um die Menüs aufzurufen.
Das Setup-Programm soll es Ihnen so leicht wie möglich machen. Es ist menüges-
teuert, d.h. Sie können in den verschiedenen Untermenüs Ihre Auswahl treffen und
die Programme werden dann automatisch installiert.
42
Français
1. Introduction
Merci pour votre achat d’une carte mère ASRock Fatal1ty FM2A88X+ Killer
Series,unecartemèretrèsableproduiteselonlescritèresdequalitérigoureuxde
ASRock. Elle offre des performances excellentes et une conception robuste confor-
mémentàl’engagementd’ASRocksurlaqualitéetlaabilitéaulongterme.
Ce Guide d’installation rapide présente la carte mère et constitue un guide
d’installation pas à pas. Des informations plus détaillées concernant la carte
mère pourront être trouvées dans le manuel l’utilisateur qui se trouve sur le CD
d’assistance.
LesspécicationsdelacartemèreetleBIOSayantpuêtremisà 
jour, le contenu de ce manuel est sujet à des changements sans
notication.Aucasoùn’importequ’ellemodicationintervenaitsurce 
manuel, la version mise à jour serait disponible sur le site web
ASRock sans nouvel avis. Vous trouverez les listes de prise en
charge des cartes VGA et CPU également sur le site Web ASRock.
Site web ASRock, http://www.asrock.com
Si vous avez besoin de support technique en relation avec cette carte
mère, veuillez consulter notre site Web pour de plus amples
informations particulières au modèle que vous utilisez.
www.asrock.com/support/index.asp
1.1 Contenu du paquet
Carte mère ASRock Fatal1ty FM2A88X+ Killer Series (Facteur de forme ATX)
Guide d’installation rapide ASRock Fatal1ty FM2A88X+ Killer Series
CD de soutien ASRock Fatal1ty FM2A88X+ Killer Series
Deux câbles de données de série ATA (SATA) (en option)
Un I/O Panel Shield
ASRock vous rappelle...
Pour bénéficier des meilleures performances sous Windows
® 8 / 8 64
bits / 7 / 7 64 bits, il est recommandé de paramétrer l'option BIOS dans
CongurationdestockageenmodeAHCI.Pourplusdedétailssurl'ins-
tallation BIOS, référez-vous au "Mode d'emploi" sur votre CD de support.
44
Français
Slot
d’extension
• 1 x slots PCI Express 3.0 x16
*PCIE 3.0 est uniquement pris en charge le
processeur FM2+. Avec le processeur FM2, seul
PCIE 2.0 est pris en charge.
• 1 x slot PCI Express 2.0 x16 (PCIE4 à mode x4)
• 2 x slots PCI Express 2.0 x1
• 3 x slots PCI
• Support de AMD Quad CrossFireXTM , CrossFireXTM
et Dual Graphics
VGA sur
carte
• APU AMD Radeon HD 8000/7000 série graphiques
A-series
• DirectX 11.1, Pixel Shader 5.0 avec processeur
FM2+. DirectX 11, Pixel Shader 5.0 avec processeur
FM2.
• mémoire partagée max 2GB
• Trois options de sortie VGA: D-Sub, DVI-D et HDMI
• Prendenchargelacongurationàtriplemoniteurs
• Prend en charge le HDMI avec une résolution
maximale jusqu’à 1920x1200 @ 60Hz
• Prend en charge le Dual-link DVI-D avec une
résolution maximale jusqu’à 2560x1600 @ 60Hz
• Prend en charge le D-Sub avec une résolution
maximale jusqu’à 1920x1600 @ 60Hz
• Prend en charge Lip Sync, Deep Color (12bpc),
xvYCC et HBR (High Bit Rate Audio: Audio à haut
débit binaire) avec HDMI (Moniteur compatible HDMI
requis)
• Prend en charge la 3D stéréoscopique Blu-ray avec
HDMI
• Supporte AMD Steady Video
TM 2.0: Nouvelle
fonctionnalité
• de traitement post-vidéo pour réduction automatique
des tremblements dans les clips vidéo en ligne/
maison
• Prise en charge de la fonction HDCP avec ports
DVI-D et HDMI
• Supporter 1080p Blu-ray(BD) avec ports DVI-D et
HDMI
45
Français
Fatal1ty FM2A88X+ Killer Series
Audio • Audio 7.1 CH HD avec protection du contenu (codec
audio Realtek ALC1150)
• Compatible audio Blu-ray Premium
• Prend en charge Purity SoundTM
-115dBSNRDACavecamplicateurdifférentiel
- TI® NE5532 (compatible Premium Headset
Amplierjusqu’à600Ohms)
- technologie Direct Drive
- capot de protection EMI
- blindage isolant PCB
• Prend en charge DTS Connect
LAN • PCIE p49-x1 Gigabit LAN 10/100/1000 Mb/s
• Qualcomm® Atheros® KillerTM E2200 Série
• Prend en charge la fonction Wake-On-LAN
• Prend en charge la fonction d’économie d’énergie
Ethernet 802,3az
• Prend en charge PXE
Panneau ar-
rière
• 1 x port souris/clavier PS/2
• 1 x port D-Sub
• 1 x port DVI-D
• 1 x port HDMI
• 1 x Port de sortie optique SPDIF
• 3 x ports USB 2.0
• 1 x port souris Fatal1ty (USB 2.0)
• 2 x ports USB 3.0 par défaut (AMD A88X
(Bolton-D4))
• 2 x ports USB 3.0 par défaut (ASMedia ASM1042A)
• 1 x port LAN RJ-45 avec LED (ACT/LED
CLIGNOTANTE et LED VITESSE)
• 1 x interrupteur d’effacement du CMOS
• Prise HD Audio: Haut-parleur arrière / Central /
Basses / Entrée Ligne / Haut-parleur frontal /
Microphone
Stockage • 8 x connecteurs 6,0 Gb/s SATA3, prise en charge
desfonctions RAID (RAID 0, RAID 1, RAID 5 et
RAID 10), NCQ, AHCI et « Connexion à chaud »
46
Français
Connecteurs •1 x En-tête de port COM
• 1 x Embase d’intrusion châssis
• 1 x embase TPM
• 1 x LED di accensione
• 2 x Connecteur pour ventilateur de CPU (1 x br. 4, 1
x br. 3)
• 3 x Connecteur pour ventilateur de Châssis (1 x br. 4,
2 x br. 3)
• 1 x Connecteur pour ventilateur de pouvoir (br. 3)
• 1 x br. 24 connecteur d’alimentation ATX
• 1 x br. 8 connecteur d’alimentation 12V ATX (con-
necteur
• d’alimentation haute densité)
• 1 x connecteur d’alimentation SLI/XFire
• 1 x Connecteur audio panneau avant
• 3 x En-tête USB 2.0 (prendre en charge 6 ports
USB 2.0 supplémentaires)
• 1 x En-tête USB 3.0 de AMD A88X (Bolton-D4)
(prendre en charge 2 ports USB 3.0 supplémen-
taires)
BIOS • 64Mb AMI UEFI Legal BIOS avec support GUI
• Support du “Plug and Play”
• Compatible pour événements de réveil ACPI 1.1
• Gestion jumperless
• Support SMBIOS 2.3.1
• DRAM, VDDP, VDDR Tension Multi-ajustement
CD
d’assistance
• Pilotes, utilitaires, logiciel anti-virus (Version
d’essai), Google ChromeBrowser et Toolbar, Start8
(30 jours d’évaluation), XSplit, Killer Network Man-
ager
47
Français
Fatal1ty FM2A88X+ Killer Series
Surveillance
système
• Détection de la température de l’UC
• Mesure de température de la carte mère
• Tachéomètre ventilateur CPU Ventilateur
• Tachéomètre ventilateur Châssis Ventilateur
• Ventilateur silencieux pour unité CPU/boîtier
• Commande de ventilateur CPU/boîtier à plusieurs
vitesses
• Détection d’OUVERTURE DE BOÎTIER
• Monitoring de la tension: +12V, +5V, +3.3V, Vcore
OS • Microsoft® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit
/ 8 64-bit / 7 32-bit / 7 64-bit
Certications • FCC, CE, WHQL
• Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP
requise)
* Pour de plus amples informations sur les produits, s’il vous plaît visitez notre site web:
http://www.asrock.com
48
Français
1.3 Réglage des cavaliers
L’illustration explique le réglage des cava-
liers. Quand un capuchon est placé sur les
broches, le cavalier est « FERME ». Si au-
cun capuchon ne relie les broches,le cava-
lier est « OUVERT ». L’illustration montre un
cavalier à 3 broches dont les broches 1 et 2
sont « FERMEES » quand le capuchon est
placé sur ces 2 broches.
Le cavalier Description
Effacer la CMOS
(CLRCMOS1)
(voirp.1g.27)
Remarque :
CLRCMOS1 vous permet d’effacer les données du CMOS. Pour effacer
et réinitialiser les paramètres du système à la conguration originale,
veuillez éteindre l’ordinateur et débrancher le cordon d’alimentation de
la prise de courant. Après 15 secondes, utilisez un couvercle de jumper
pour court-circuiter les broches pin2 et pin3 de CLRCMOS1 pendant
5
secondes. Veuillez cependant ne pas effacer le CMOS immédiatement
a
près avoir mis à jour le BIOS. Si vous avez besoin d’effacer le CMOS
après avoir mis à jour le BIOS, vous devez allumer en premier le
système, puis l’éteindre avant de continuer avec l’opération d’effacement
duCMOS.Veuilleznoterquelemotdepasse,ladate,l’heure,leprol
par défaut de l’utilisateur et l’adresse MAC seront effacés seulement si
la batterie du CMOS est enlevée.
Effacer la
CMOS
Paramètres
par défaut
1. Si vous effacez la CMOS, il se peut qu’une ouverture du boîtier
soitdétectée. Veuillez ajuster l’option du BIOS “Clear Status”
(Effacerl’état) pour effacer la mention d’état d’intrusion dans le
châssis.
2. Le bouton Clear CMOS possède la même fonction que le cavalier
(jumper) Clear CMOS.
49
Français
Fatal1ty FM2A88X+ Killer Series
En-tête USB 2.0 A côté des quatre ports USB
(USB_5_6 br.9) 2.0 par défaut sur le panneau
(voir p.1 No. 22) E/S, il y a trois embases USB
(USB_7_8 br.9) 2.0 sur cette carte mère.
(voir p.1 No. 21) Chaque embase USB 2.0 peut
(USB_9_10 br.9) prendre en charge 2 ports USB
(voir p.1 No. 20) 2.0.
Connecteurs Série ATA3 Ces huit connecteurs Série
(SATA3_1_2: voir p.1 No. 10) ATA3 (SATA3) prennent en
(SATA3_3_4: voir p.1 No. 11) charge les câbles SATA pour
(SATA3_5_6: voir p.1 No. 12) les périphériques de stockage
(SATA3_7_8: voir p.1 No. 13) internes. L’interface SATA3
actuelle permet des taux
transferts de données pouvant
aller jusqu’à 6,0 Gb/s.
1.4 En-têtes et Connecteurs sur Carte
Les en-têtes et connecteurs sur carte NE SONT PAS des cavaliers.
NE PAS placer les capuchons de cavalier sur ces en-têtes et con-
necteurs. Le fait de placer les capuchons de cavalier sur les en-
têtes et connecteurs causera à la carte mère des dommages irré-
versibles!
En-tête USB 3.0 En plus des quatre ports USB
(USB3_5_6 br. 19) 3.0 par défaut sur le panneau
(voir p.1 No. 8) E/S, il y a une barrette USB 3.0
sur la carte mère. Cette barrette
USB 3.0 peut prendre en
charge deux ports USB 3.0.
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
U RSB_PW
1
1
IntA_PB_D+
Dummy
IntA_PB_D-
GND
IntA_PB_SSTX+
GND
IntA_PB_SSTX-
IntA_PB_SSRX+
IntA_PB_SSRX-
VbusVbus
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA _D-
IntA_PA _D+
SATA3_1_2SATA3_5_6 SATA3_3_4SATA3_7_8
50
Français
Connecteur audio panneau C’est une interface pour
(HD_AUDIO1 br. 9) un câble avant audio en façade
(voir p.2 No. 26) qui permet le branchement et
le contrôle commodes de
périphériques audio.
1.L’audioàhautedénition(HDA)prendenchargeladétectiondeche, 
maisleldepanneausurlechâssisdoitprendreenchargeleHDApour 
fonctionner correctement. Veuillez suivre les instructions dans notre
 manueletlemanueldechâssisaninstallervotresystème.
2. Si vous utilisez le panneau audio AC’97, installez-le sur l’adaptateur audio
du panneau avant conformément à la procédure ci-dessous :
A. Connectez Mic_IN (MIC) à MIC2_L.
B. Connectez Audio_R (RIN) à OUT2_R et Audio_L (LIN) à OUT2_L.
C. Connectez Ground (GND) à Ground (GND).
D. MIC_RET et OUT_RET sont réservés au panneau audio HD. Vous
n’avez pas besoin de les connecter pour le panneau audio AC’97.
E. Pour activer le micro avant.
Pour les systèmes d’exploitation Windows
® 8 / 8 64 bits / 7 / 7 64 bits:
Allez sur l’onglet “FrontMic” (Micro avant) sur le Panneau de contrôle
Realtek. Ajustez “Recording Volume” (Volume d’enregistrement).
En-tête du panneau système Cet en-tête permet d’utiliser
(PANEL1 br.9) plusieurs fonctions du
(voir p.1 No. 14) panneau système frontal.
Connectez l’interrupteur d’alimentation, l’interrupteur de réinitialisation et
l’indicateur d’état du système du châssis sur cette barrette en respectant
l’affectation des broches décrite ci-dessous. Faites attention aux broches
positives et négatives avant de connecter les câbles.
52
Français
Connecteur du ventilateur Veuillez connecter le câble de
de l’UC ventilateur d’UC sur ce
(CPU_FAN1 br. 4)  connecteuretbrancherlel
(voir p.1 No. 3) noir sur la broche de terre.
Bien que cette carte mère offre un support de (Ventilateur silencieux
ventilateur de CPU à 4 broches , le ventilateur de CPU à 3 broches peut
bien fonctionner même sans la fonction de commande de vitesse du
ventilateur. Si vous prévoyez de connecter le ventilateur de CPU à 3
broches au connecteur du ventilateur de CPU sur cette carte mère,
veuillez le connecter aux broches 1-3.
Installation de ventilateur à 3 broches
Broches 1-3 connectées
(CPU_FAN2 br. 3)
(voir p.1 No. 4)
En-tête d’alimentation ATX Veuillez connecter l’unité
(ATXPWR1 br. 24) d’alimentation ATX sur cet en-
(voir p.1 No. 7) tête.
12
1
24
13
Connecteur pour châssis
et ventilateur
(CHA_FAN1 br. 4)
(voir p.1 No. 17)
(CHA_FAN2 br. 3)
(voir p.1 No. 15)
(CHA_FAN3 br. 3)
(voir p.1 No. 9)
(PWR_FAN1 br. 3)
(voir p.1 No. 2)
Branchez les câbles du
ventilateur aux connecteurs pour
ventilateur et faites correspondre
lelnoiràlabrochedeterre.
GND
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTROL
1 2 3 4
GND
+ 12V
CPU_
FAN_SPEED
FAN_SPEED_CONT ROL
GND
+12V
CPU_FAN_SPEED
53
Français
Fatal1ty FM2A88X+ Killer Series
Connecteur ATX 12V Veuillez connecter une unité
(ATX12V1 br.8) d’alimentation électrique ATX
(voir p.1 No. 1) 12V sur ce connecteur.
Bien que cette carte mère possède 8 broches connecteur d’alimentation
ATX 12V, il peut toujours travailler si vous adoptez une approche
traditionnelle à 4 broches ATX 12V alimentation. Pour utiliser
l’alimentation des 4 broches ATX, branchez votre alimentation
avec la broche 1 et la broche 5.
4-Installation d’alimentation à 4 broches ATX 12V
En-tête de port COM Cette en-tête de port COM est
(COM1 br.9) utilisée pour prendre en charge
(voir p.1 No. 25) un module de port COM.
Connecteur
d’alimentation SLI/XFire
(SLI/XFIRE_PWR1 à 4
broches)
(voir p.1 No. 24)
Bien que cette carte mère fournisse un connecteur de
courant ATX 24 broches, elle peut encore fonctionner
si vous adopter une alimentation traditionnelle ATX 20
broches. Pour utiliser une alimentation ATX 20 broches,
branchez à l’alimentation électrique ainsi qu’aux
broches 1 et 13.
20-Installation de l’alimentation électrique ATX
12
1
24
13
8 5
4 1
CC TS # 1
RR TS # 1
D DS R# 1
D DT R # 1
RRXD1
GND
TTXD 1
D DC D # 1
1
RR I# 1
Veuillez brancher ce
connecteur avec un
connecteur d’alimentation
de disque dur lorsque deux
cartes graphiques sont
installées sur la carte mère.
54
Français
Embase d’intrusion châssis Cette carte-mère prend
(CI1 br.2) en charge la détection
(voir p.1 No. 19) d’OUVERTURE DE BOÎTIER,
quidétecte tout retrait du
capot duchâssis. Cette fonction-
nécessite un châssis qui a été-
conçu pour la
détectiond’intrusion dans le
châssis.
Embase d’intrusion châssis
Embase TPM
(TPMS1 à 17 broches)
1
Signal
GND
1
LFRAME #_ L
CK_ 33M _T PM
TPM _RST#
LAD3_L
+3V
LAD0_L
+3VSB
GNDF_CLKRUN#
SERIRQ#
S_PWRDWN#
GND
LAD1_L
LAD2_L
SMB_D A
TA_ MAIN
SMB_CLK_MAI N
GND
Ce connecteur prend en charge
un module TPM (Trusted
Platform Module – Module
de plateforme sécurisée),
qui permet de sauvegarder
clés,certicatsnumériques,
mots de passe et données
en toute sécurité. Le système
TPM permet également de
renforcer la sécurité du réseau,
de protéger les identités
numériques et de préserver
l’intégrité de la plateforme.
55
Français
Fatal1ty FM2A88X+ Killer Series
2. Informations sur le BIOS
La puce Flash Memory sur la carte mère stocke le Setup du BIOS. Lorsque vous
démarrez l’ordinateur, veuillez presser <F2> ou <Del> pendant le POST (Power-On-
Self-Test) pour entrer dans le BIOS; sinon, le POST continue ses tests de routine. Si
vous désirez entrer dans le BIOS après le POST, veuillez redémarrer le système en
pressant <Ctl> + <Alt> + <Suppr>, ou en pressant le bouton de reset sur le boîtier
du système. Vous pouvez également redémarrer en éteignant le système et en le
rallumant. L’utilitaire d’installation du BIOS est conçu pour être convivial. C’est un
programmepilotéparmenu,quivouspermetdefairedélerparsesdiverssous-
menus et de choisir parmi les choix prédéterminés. Pour des informations détaillées
surleBIOS,veuillezconsulterleGuidedel’utilisateur(chierPDF)dansleCD
technique.
3. Informations sur le CD de support
Cette carte mère supporte divers systèmes d’exploitation Microsoft
® Windows®:
8 / 8 64 bits / 7 / 7 64 bits. Le CD technique livré avec cette carte mère contient les
pilotes et les utilitaires nécessaires pour améliorer les fonctions de la carte mère.
Pour utiliser le CD technique, insérez-le dans le lecteur de CD-ROM. Le Menu prin-
cipals’afcheautomatiquementsi“AUTORUN”estactivédansvotreordinateur.Si
le Menu principal n’apparaît pas automatiquement, localisez dans le CD technique
lechier“ASSETUP.EXE”dansledossierBINetdouble-cliquezdessuspouraf-
cher les menus.
56
Italiano
1. Introduzione
Grazie per aver scelto una scheda madre ASRock Fatal1ty FM2A88X+ Killer
Series,unaschedamadreafdabileprodottasecondoisevericriteridiqualità
ASRock. Le prestazioni eccellenti e il design robusto si conformano all’impegno di
ASRock nella ricerca della qualità e della resistenza.
Questa Guida Rapida all’Installazione contiene l’introduzione alla motherboard e la
guidapasso-passoall’installazione.Informazionipiùdettagliatesullamotherboardsi
possono trovare nel manuale per l’utente presente nel CD di supporto.
LespecichedellaschedamadreeilsoftwaredelBIOSpossono 
essere aggiornati, pertanto il contenuto di questo manuale può subire
variazioni senza preavviso. Nel caso in cui questo manuale sia
 modicato,laversioneaggiornatasaràdisponibilesulsitodiASRock
 senzaaltroavviso.SulsitoASRocksipossonoanchetrovarelepiù
recenti schede VGA e gli elenchi di CPU supportate.
ASRock website http://www.asrock.com
Se si necessita dell’assistenza tecnica per questa scheda madre,
visitareilnostrositoperinformazionispecichesulmodellochesi 
sta usando.
www.asrock.com/support/index.asp
1.1 Contenuto della confezione
Scheda madre ASRock Fatal1ty FM2A88X+ Killer Series (ATX Form Factor)
Guida di installazione rapida ASRock Fatal1ty FM2A88X+ Killer Series
CD di supporto ASRock Fatal1ty FM2A88X+ Killer Series
Due cavi dati Serial ATA (SATA) (opzionali)
Un I/O Shield
ASRock vi ricorda...
Per ottenere migliori prestazioni in Windows
® 8 / 8 64-bit / 7 / 7 64-bit, si
consigliadiimpostarel'opzioneBIOSinStorageConguration(Congu-
razione di archiviazione) sulla modalità AHCI. Per l'impostazione BIOS,
fare riferimento a “User Manual” (Manuale dell'utente) nel CD di supporto
per dettagli.
57
Italiano
Fatal1ty FM2A88X+ Killer Series
1.2 Speciche
Piatta-
forma
• ATX Form Factor
• Design condensatore Premium Gold (condensatori a
conduttore in polimero di alta qualità realizzati al 100%
in Giappone)
Stile su-
periore
• Purity SoundTM
Armatura
dagioco
Potenza CPU
• Connettore alimentazione ad alta densità
Scheda VGA
• 15μGoldFingernell’alloggioVGAPCIe(PCIE2)
• Connettore del connettore di alimentazione SLI/XFire
Internet
• Qualcomm® Atheros® Killer
TM LAN
Audio
• Purity SoundTM
Proces-
sore
• Supporto per processori socket FM2+ 95W / FM2 100W
• Design Digi Power
• Struttura di fase con alimentazione 4 + 2
Chipset • AMD A88X (Bolton-D4)
Memoria • Supporto tecnologia Dual Channel Memory
• 4 x slot DDR3 DIMM
• Supporto DDR3 2600+(OC)/2400(
OC)/2133/1866/1600/1333/1066 non-ECC, momoria
senza buffer
* DDR3 2600+ è supportato solo con due DIMM.
• Capacità massima della memoria di sistema: 64GB
• Supporto di Intel®XMP(ExtremeMemoryProle)1.3/1.2
• SupportatecnologiaAMDMemoryProle(AMP)noad
AMP 2400
58
Italiano
Slot di es-
pansione
• 1 x slot PCI Express 3.0 x16
* PCIE 3.0 è supportato solo con CPU FM2+. Con CPU
FM2, supporta solo PCIE 2.0.
• 1 x slot PCI Express 2.0 x16 (PCIE4: modalità x4)
• 2 x slot PCI Express 2.0 x1
• 3 x slot PCI
• Supporta AMD Quad CrossFireXTM, CrossFireXTM e
Dual Graphics
VGA su
scheda
• GracaserieAMDRadeonHD8000/7000integratain
APU serie A
• DirectX 11.1, Pixel Shader 5.0 con CPU FM2+. DirectX
11, Pixel Shader 5.0 con CPU FM2.
• Memoria massima condivisa 2GB
• Tre opzioni d’output VGA: D-Sub, DVI-D e HDMI
• Supporta il triplo monitor
• SupportaHDMI1.4aconrisoluzionemassimanoa
1920x1200 @ 60Hz
• SupportaDual-linkDVI-Dconrisoluzionemassimano
a 2560x1600 @ 60Hz
• SupportaD-Subconrisoluzionemassimanoa
1920x1200 @ 60Hz
• Supporto delle funzioni Auto Lip Sync, Deep Color
(12bpc), xvYCC e HBR (High Bit Rate Audio) con HDMI
(è necessario un monitor compatibile HDMI)
• Supporta Blu-ray Stereoscopico in 3D con HDMI
• Supporta AMD Steady Video
TM 2.0: Nuova capacità di
post-elab orazione video per la riduzione automatica
delle vibrazioni nei video a casa/on-line
• Supporto della funzione HDCP con le porte DVI-D e
HDMI
• Supporto 1080p Blu-ray (BD) riproduzione con le porte
DVI-D e HDMI
59
Italiano
Fatal1ty FM2A88X+ Killer Series
Audio • Audio HD a 7.1 canali con Content Protection (codec
audio Realtek ALC1150)
• Supporto audio Blu-ray Premium
• Supporta Purity SoundTM
-115dBSNRDACconamplicatoredifferenziale
- TI®NE5532(supportal'amplicatorepercufedi
qualitàsuperiorenoa600Ohm)
- Tecnologia Direct Drive
- copertura a schermo EMI
- schermo isolato PCB
• Supporta DTS Connect
LAN • PCIE p63-x1 LAN Gigabit 10/100/1000 Mb/s
• Qualcomm® Atheros® Killer
TM E2200 Serie
• Supporta Wake-On-LAN
• SupportaEnergyEfcientEthernet802.3az
• Supporta PXE
Pannello
posteri-
ore I/O
• 1 x porta PS/2 per mouse/tastiera
• 1 x Porta D-Sub
• 1 x Porta DVI-D
• 1 x Porta HDMI
• 1 x Porta ottica SPDIF Out
• 3 x porte USB 2.0
• 1 x porta mouse Fatal1ty (USB 2.0)
• 2 x porte USB 3.0 già integrate (AMD A88X (Bolton-D4))
• 2 x porte USB 3.0 già integrate (ASMedia ASM1042A)
• 1 x porte LAN RJ-45 con LED (LED azione/
collegamento e LED velocità)
• 1 x interruttore di pulizia CMOS
• Connettore HD Audio: cassa posteriore / cassa centrale
/bassi / ingresso linea / cassa frontale / microfono
Archivi-
azione
• 8 x connettori SATA3 6,0 Gb/s, supporto di RAID (RAID
0, RAID 1, RAID 5 e RAID 10) e delle funzioni NCQ,
AHCI e “Hot Plug”
60
Italiano
Connet-
tori
• 1 x collettore porta COM
• 1 x header di intrusione dello chassis
• 1 x header TPM
• 1 x LED di accensione
• 2 x Connettore CPU ventola (1 x 4-pin, 1 x 3-pin)
• 3 x Connettore Chassis ventola (1 x 4-pin, 2 x 3-pin)
• 1 x Connettore Alimentazione ventola (3-pin)
• 1 x 24-pin collettore alimentazione ATX
• 1 x 8-pin connettore ATX 12V (connettore alimentazione
ad alta densità)
• 1 x connettore del connettore di alimentazione SLI/
XFire
• 1 x Connettore audio sul pannello frontale
• 3 x Collettore USB 2.0 (supporta 6 porte USB 2.0)
• 1 x Collettore USB 3.0 di AMD A88X (Bolton-D4) (sup-
porta 2 porte USB 3.0)
BIOS • 64Mb AMI UEFI Legal BIOS con interfaccia di supporto
• Supporta “Plug and Play”
• Compatibile con ACPI 1.1 wake up events
• Supporta jumperfree
• Supporta SMBIOS 2.3.1
• Regolazione multi-voltaggio DRAM, VDDP, VDDR
CD di
supporto
• Driver, utilità, software antivirus (Versione dimostrativa),
Google Chrome Browser e Toolbar, Start8 (30 giorni di
prova), Xsplit, Killer Network Manager
Monito-
raggio-
Hardware
• Sensore per la temperatura del processore
• Sensore temperatura scheda madre
• Indicatore di velocita per la ventola del CPU
• Indicatore di velocita per la ventola del Chassis
• Ventola CPU/chassis silenziosa
• Ventola CPU/chassis con controllo di varie velocità
• Rilevamento CASE APERTO
• Voltaggio: +12V, +5V, +3.3V, Vcore
61
Italiano
Fatal1ty FM2A88X+ Killer Series
Compati-
bilità SO
• Microsoft® Windows® 8.1 32 bit / 8.1 64 bit / 8 32 bit / 8
64 bit /7 32 bit / 7 64 bit
Certica-
zioni
• FCC, CE, WHQL
• Predisposto ErP/EuP (è necessaria l’alimentazione
predis posta per il sistema ErP/EuP)
* Per ulteriori informazioni, prego visitare il nostro sito internet:
http://www.asrock.com
62
Italiano
1.3 Setup dei Jumpers
L’illustrazione mostra come sono settati i jump-
er. Quando il ponticello è posizionato sui pin,
il jumper è “CORTOCIRCUITATO”. Se sui pin
non ci sono ponticelli, il jumper è “APERTO”.
L’illustrazione mostra un jumper a 3 pin in cui il
pin1 e il pin2 sono “CORTOCIRCUITATI” quan-
do il ponticello è posizionato su questi pin.
Jumper Settaggio del Jumper
Resettare la CMOS
(CLRCMOS1)
(vedi p.1 item 27)
Nota:
CLRCMOS1 permette si azzerare i dati nella CMOS. Per cancellare e ripristinare
i
 parametri del sistema sulla congurazione iniziale, spegnere il computer e
scollegare il cavo d’alimentazione dalla presa di corrente. Attendere 15 secondi,
poi usare un cappuccio jumper per cortocircuitare il pin 2 ed il pin 3 su
CLRCMOS1 per 5 secondi. Tuttavia, si consiglia di non cancellare la CMOS
subito dopo avere aggiornato il BIOS. Se si deve azzerare la CMOS quando si
è completato l’aggiornamento del BIOS, è necessario per prima cosa avviare il
sistema e poi spegnerlo prima di eseguire l’azzeramento della CMOS. Notare
che password, data, ore, prolo utente predenito e indirizzo MAC saranno
cancellati solo se è rimossa la batteria della CMOS.
Azzeramen-
to CMOS
Impostazione
predenita
1. Se si cancella la CMOS, potrebbe essere rilevata l’apertura del
case.Regolare l’opzione del BIOS “Clear Status” (Cancella stato)
per cancellarela registrazione del precedente stato d’intrusione
chassis.
2. L’interruttore per azzerare la CMOS ha la stessa funzione del
jumper per azzerare la CMOS.
63
Italiano
Fatal1ty FM2A88X+ Killer Series
Connettori Serial ATA3 Questi otto connettori Serial
(SATA3_1_2: vedi p.1 Nr. 10) ATA3 (SATA3) supportano cavi
(SATA3_3_4: vedi p.1 Nr. 11) dati SATA per dispositivi di
(SATA3_5_6: vedi p.1 Nr. 12) immagazzinamento interni.
(SATA3_7_8: vedi p.1 Nr. 13) ATA3 (SATA3) supportano cavi
SATA per dispositivi di memoria
interni. L’interfaccia SATA3
attuale permette velocità di
 trasferimentodatinoa
6.0 Gb/s.
Collettore USB 2.0 Oltre alle quattro porte USB 2.0
(9-pin USB_5_6)  predenitenelpannelloI/O,la
(vedi p.1 Nr. 22) scheda madre dispone di
(9-pin USB_7_8) tre intestazioni USB 2.0.
(vedi p.1 Nr. 21) Ciascuna intestazione USB 2.0
(9-pin USB_9_10) supporta due porte USB 2.0.
(vedi p.1 Nr. 20)
1.4 Collettori e Connettori su Scheda
I collettori ed i connettori su scheda NON sono dei jumper. NON instal-
lare cappucci per jumper su questi collettori e connettori. L’installazione
di cappucci per jumper su questi collettori e connettori provocherà
danni permanenti alla scheda madre!
Collettore USB 3.0 Oltre alle quattro porte USB 3.0
(19-pin USB3_5_6) standard del pannello I/O,
(vedi p.1 Nr. 8) questa scheda madre è dotata
di un header USB 3.0 che
supporta due porte USB 3.0.
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
U RSB_PW
1
1
IntA_PB_D+
Dummy
IntA_PB_D-
GND
IntA_PB_SSTX+
GND
IntA_PB_SSTX-
IntA_PB_SSRX+
IntA_PB_SSRX-
VbusVbus
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
SATA3_1_2SATA3_5_6 SATA3_3_4SATA3_7_8
64
Italiano
Connettore audio sul È un’interfaccia per il cavo del
pannello frontale pannello audio. Che consente
(9-pin HD_AUDIO1) connessione facile e controllo
(vedi p.1 Nr. 26) dei dispositivi audio.
1.LacaratteristicaHDA(HighDenitionAudio)supportailrilevamentodei 
connettori, però il pannello dei cavi sul telaio deve supportare la funzione
HDA(HighDenitionAudio)perfarsìchequestaoperiinmodocorretto. 
Attenersi alle istruzioni del nostro manuale e del manuale del telaio per
installare il sistema.
2. Se si utilizza un pannello audio AC’97, installarlo nell’intestazione audio
del pannello anteriore, come indicato di seguito:
A. Collegare Mic_IN (MIC) a MIC2_L.
B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) ad OUT2_L.
C. Collegare Ground (GND) a Ground (GND).
D. MIC_RET e OUT_RET sono solo per il pannello audio HD. Non è
necessario collegarli per il pannello audio AC’97.
E. Per attivare il microfono frontale.
Sistema operativo Windows® 8 / 8 64-bit / 7 / 7 64-bit:
Andare alla scheda “FrontMic” (Microfono frontale) del pannello di
controllo Realtek. Regolare la voce “Recording Volume” (Volume
registrazione).
Collettore pannello di sistema Questo collettore accomoda
(9-pin PANEL1) diverse funzioni di sistema
(vedi p.1 Nr. 14) pannello frontale.
Collegare l’interruttore d’alimentazione, l’interruttore di ripristino,
l’indicatore di stato del sistema del pannello frontale del telaio a questo
  headerinbaseall’assegnazionedeipindenitadiseguito.Determinarei
pin positivi e negativi prima di collegare i cavi.
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
GND
R #E SET
PWRBT N#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
65
Italiano
Fatal1ty FM2A88X+ Killer Series
PWRBTN (interruttore d’alimentazione):
Va collegato all’interruttore d’alimentazione del pannello frontale del
  telaio.Usandol’interruttored’alimentazionesipuòcongurareilmodoin
cui si spegne il sistema.
RESET (interruttore di ripristino):
Va collegato all’interruttore di ripristino del pannello frontale del telaio.
Premere l’interruttore di ripristino per riavviare il sistema se il computer si
blocca e non riesce ad eseguire un normale riavvio.
PLED (LED alimentazione del sistema):
Va collegato all’indicatore di stato d’alimentazione del pannello frontale
del telaio. Il LED è acceso quando il sistema è operativo. Il LED continua
a lampeggiare quando il sistema è in stato di standby S3. Il LED è
spento quando il sistema è in stato di sospensione /ibernazione S4
oppure spento (S5).
HDLED (LED attività disco rigido):
Va collegato al LED attività disco rigido del pannello frontale del telaio. Il
LED è acceso quando disco rigido legge e scrive i dati.
Il design del pannello frontale può variare in base ai telai. Il modulo di
un pannello frontale può consistere di: interruttore d’alimentazione,
interruttore di ripristino, LED d’alimentazione, LED attività disco rigido,
casse, eccetera. Quando si collega il modulo del pannello frontale a
  questoheader,assicurarsichel’assegnazionedeiliedeipinsiafatta
corrispondere in modo appropriato.
Collettore casse telaio Collegare le casse del telaio a
(4-pin SPEAKER1) questo collettore.
(vedi p.1 Nr. 16)
LED di accensione Collegare il LED di accensione
(3-pin PLED1) chassi per indicare lo stato di
(vedi p.1 Nr. 18) alimentazione del sistema. Il
LED è acceso quando il sistema
è in funzione. Il LED continua a
lampeggiare in stato S3. Il LED
è spento in stato S4 o S5
(spegnimento).
1
+5V
DUMM Y
DUMM Y
SPEAKER
1
PLED+
PLED+
PLED-
66
Italiano
Connettore ventolina CPU Collegare il cavo della ventolina
(4-pin CPU_FAN1) CPU a questo connettore e far
(vedi p.1 Nr. 3)  combaciareilloneroalpin
terra.
Sebbene la presente scheda madre disponga di un supporto per ventola
CPU a 4 piedini (ventola silenziosa), la ventola CPU a 3 piedini è in
grado di funzionare anche senza la funzione di controllo della velocità
della ventola. Se si intende collegare la ventola CPU a 3 piedini al
connettore della ventola CPU su questa scheda madre, collegarla ai
piedini 1-3. Piedini 1-3 collegati
Installazione della ventola a 3 piedini
(3-pin CPU_FAN2)
(vedi p.1 Nr. 4)
Installazione dell’alimentatore ATX a 20 pin
Con questa scheda madre, c’è in dotazione un
connettore elettrico ATX a 24 pin, ma può funzionare lo
stesso se si adotta un alimentatore ATX a 20 pin. Per
usare l’alimentatore ATX a 20 pin, collegare l’alimentatore
con il Pin 1 e il Pin 13.
Connettore alimentazione ATX Collegare la sorgente
(24-pin ATXPWR1) d’alimentazione ATX a questo
(vedi p.1 Nr. 7) connettore.
12
1
24
13
12
1
24
13
Collettori Chassis ed Collegare i cavi della ventola ai
alimentazione ventola corrispondenti connettori
(4-pin CHA_FAN1) facendo combaciare il cavo
(vedi p.1 Nr. 17) nero col pin di terra.
(3-pin CHA_FAN2)
(vedi p.1 Nr. 15)
(3-pin CHA_FAN3)
(vedi p.1 Nr. 9)
(3-pin PWR_FAN1)
(vedi p.1 Nr. 2)
GND
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTROL
1 2 3 4
GND
+ 12V
CPU_
FAN_SPEED
FA
N_SPEED_CONT ROL
GND
+12V
CPU_FAN_SPEED
67
Italiano
Fatal1ty FM2A88X+ Killer Series
Collettore porta COM Questo collettore porta COM è
(9-pin COM1) utilizzato per supportare il
(vedi p.1 Nr. 25) modulo porta COM.
Connettore alimentazione
SLI/XFIRE
(SLI/XFIRE_PWR14 pin)
(vedi p.1 Nr. 24)
Header di intrusione dello chassis Questa scheda madre supporta
(2-pin CI1) la funzione di rilevamento del
(vedi p.1 Nr. 19) CASE APERTOche rileva che
il coperchio dellochassis è stato
rimosso.Questa funzione
richiede unochassis con
struttura dirilevamento di
intrusione dellochassis.
Sebbene questa schedamadre fornisca un connettore elettrico 8-pin ATX
12V, l‘unita‘ puo‘ ancora essere funzionante se viene utilizzata una
fornitura elettrica tradizionale a 4-pin ATX 12V. Per usare tale fornitura
elettrica 4-pin ATX 12V, prego collegare la presa elettrica
al Pin 1 e Pin 5.
Installazione elettrica 4-Pin ATX 12V
Connettore ATX 12 V Collegare un alimentatore ATX
(8-pin ATX12V1) 12 V a questo connettore.
(vedi p.1 Nr. 1)
8 5
4 1
1
Signal
GND
Collegare questo
connettore al connettore di
alimentazione di un disco
rigido quando le due schede
grachesonoinstallatesu
questa scheda madre.
68
Italiano
Header TPM Questo connettore supporta il
(TPMS1 17 pin) sistema Trusted Platform Mo-
(vedi p.1 No. 23) dule (TPM), che può archiviare
 inmodosicurochiavi,certicati
digitali, password e dati. Un
sistema TPM permette anche di
potenziare la sicurezza della
rete, di proteggere identità digi-
tali e di garantire l’integrità della
piattaforma.
1
LF RAME #_ L
CK_3 3M_T PM
TP M_ RST#
LA D3_L
+3 V
LA D0_L
+3 VSB
GN DF_ CL KRUN #
SE RI RQ #
S_ PWRD WN#
GND
LA D1_L
LA D2_L
SM B_ DA
TA_ MA IN
SM B_ CL K_ MAIN
GND
69
Italiano
Fatal1ty FM2A88X+ Killer Series
2. Informazioni sul BIOS
La Flash Memory sulla scheda madre contiene le Setup Utility. Quando si avvia il
computer, premi <F2> o <Del> durante il Power-On-Self-Test (POST) della Setup
utility del BIOS; altrimenti, POST continua con i suoi test di routine. Per entrare il
BIOS Setup dopo il POST, riavvia il sistema premendo <Ctl> + <Alt> + <Delete>, o
premiiltastodiresetsullochassisdelsistema.Perinformazionipiùdettagliatecirca
ilSetupdelBIOS,fareriferimentoalManualedell’Utente(PDFle)contenutonelcd
di supporto.
3. Software di supporto e informazioni su
CD
Questa scheda madre supporta vari sistemi operativi Microsoft
® Windows®: 8 / 8 64-
bit / 7 / 7 64-bit. Il CD di supporto a corredo della scheda madre contiene i driver e
utilità necessari a potenziare le caratteristiche della scheda. Inserire il CD di sup-
porto nel lettore CD-ROM. Se la funzione “AUTORUN” è attivata nel computer,
appariràautomaticamenteilMenùprincipale.SeilMenùprincipalenonappareau-
tomaticamente,posizionarsi sulle “ASSETUP.EXE”nelCESTINO delCD disup-
portoecliccareduevoltepervisualizzareimenù.
70
Español
1. Introducción
Gracias por su compra de ASRock placa madre,Fatal1ty FM2A88X+ Killer Series
unaplacadeconanzaproducidabajoelcontroldecalidadestrictoypersistente.
La placa madre provee realización excelente con un diseño robusto conforme al
compromiso de calidad y resistencia de ASRock.
Esta Guía rápida de instalación contiene una introducción a la placa base y una
guía de instalación paso a paso. Puede encontrar una información más detallada
sobre la placa base en el manual de usuario incluido en el CD de soporte.
 PorquelasespecicacionesdelaplacamadreyelsoftwaredeBIOS
podrían ser actualizados, el contenido de este manual puede ser cambiado
 sinaviso.Encasodecualquiermodicacióndeestemanual,laversión
actualizada estará disponible en el website de ASRock sin previo aviso.
También encontrará las listas de las últimas tarjetas VGA y CPU soportadas
en la página web de ASRock.
Website de ASRock http://www.asrock.com
Si necesita asistencia técnica en relación con esta placa base, visite
 nuestrapáginawebconelnúmerodemodeloespecícodesuplaca.
www.asrock.com/support/index.asp
1.1 Contenido de la caja
Placa base ASRock (Factor forma ATX)Fatal1ty FM2A88X+ Killer Series
Guía de instalación rápida de ASRock Fatal1ty FM2A88X+ Killer Series
CD de soporte de ASRock Fatal1ty FM2A88X+ Killer Series
Dos cables de datos Serial ATA (SATA) (Opcional)
Una protección I/O
ASRock le recuerda...
Para mejorar el rendimiento en Windows
® 8 / 8 64 bits / 7 / 7 64 bits,
es recomendable establecer la opción del BIOS de la conguración de
almacenamientoenelmodoAHCI.Paraobtenerdetallessobrelacon-
guración del BIOS, consulte el “Manual del usuario” que se encuentra en
nuestro CD de soporte.

Produkt Specifikationer

Mærke: Asrock
Kategori: Bundkort
Model: Fatal1ty FM2A88X+ Killer

Har du brug for hjælp?

Hvis du har brug for hjælp til Asrock Fatal1ty FM2A88X+ Killer stil et spørgsmål nedenfor, og andre brugere vil svare dig


Bundkort Asrock Manualer

Asrock

Asrock 945GCM-S Manual

13 Januar 2025
Asrock

Asrock GE PRO-M Manual

13 Januar 2025
Asrock

Asrock Rack D1848TERD4U-4Q Manual

27 December 2024
Asrock

Asrock Rack B550D4M Manual

13 November 2024
Asrock

Asrock Rack B550D4-4L Manual

13 November 2024
Asrock

Asrock Rack B450D4U-V1L Manual

13 November 2024
Asrock

Asrock Rack ALTRAD8UD2-1L2Q Manual

13 November 2024
Asrock

Asrock Rack B550D4U Manual

13 November 2024
Asrock

Asrock G31M-GS R2.0 Manual

10 Oktober 2024
Asrock

Asrock 775Dual-880Pro Manual

3 Oktober 2024

Bundkort Manualer

Nyeste Bundkort Manualer

Asus

Asus PRIME B760M-F D4 Manual

27 Marts 2025
Raspberry Pi

Raspberry Pi Pico 2 Manual

6 Marts 2025
Asus

Asus B860M AYW Gaming WIFI Manual

15 Februar 2025
MSI

MSI MAG B850 Tomahawk MAX WIFI Manual

15 Februar 2025
MSI

MSI PRO B860-P Manual

15 Februar 2025
MSI

MSI MPG X870E Carbon WIFI Manual

15 Februar 2025
MSI

MSI MPG Z890I EDGE TI WIFI Manual

15 Februar 2025
MSI

MSI MEG X870E GODLIKE Manual

15 Februar 2025
MSI

MSI PRO B650-VC WIFI II Manual

15 Februar 2025
MSI

MSI PRO Z890-P Manual

12 Februar 2025