Auray CFP-ET2 Manual


Læs nedenfor 📖 manual på dansk for Auray CFP-ET2 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
CFP-ET Series
Carbon Fiber
Extension Tubes
for CFP-Series Boom Poles
Owners Manual
Extension tube
accessory for use
with Auray CFP-
series boom poles.
Manufactured with
sturdy, lightweight
carbon ber for
portability and
reliability.
Integrated cable
with high-quality
TA3 (mini XLR)
connectors
manufactured by
Rean® (a registered
trademark of
Neutrik®).
www.AurayAudio.com
Adding an Extension Boom Pole with
Side-Exit XLR
1. Unscrew the side exit housing, 1 and
move the plastic strain relief cap so that
the TA3 connector inside the housing is
exposed.
2. Disconnect the TA3 connector by pressing
on the locking tab and gently removing the
connector from the mount. 2
Note: The TA3 connector should easily
disconnect. Do not force or pull on the
cable to disconnect it. Doing so could
damage the housing or the connector.
3. Use a small slotted screwdriver to reach
inside the strain relief and depress the
locking tab of the TA3 connector. With the
locking tab depressed, you can slide the
strain relief over the TA3 connector and o
of the cable. 3 Set the strain relief piece
aside.
4. Connect the male TA3 connector of the
included cable to the female TA3 connector
of the coiled cable of the boom pole.
5. Snake the included cable through the
extension tube.
6. Screw the extension tube onto the end of
the boom pole.
7. Fit the narrow side of the strain relief over
the TA3 connector, and push it past the
TA3 connector’s locking tab. 4
8. Plug the TA3 connector into the bottom
housing by inserting it into the TA3 mount
and pushing in until it clicks.
Note: When properly aligned, the TA3
connector will easily slide into place.
Do not try to force the connector into
the mount. Doing so could damage the
connector or the mount.
9. Push the strain relief all the way into the
side exit housing so it sits over the TA3
connector. 5
10. Screw the side exit housing onto the end of
the boom pole.
5
4
1
2
3
Auray is a registered trademark of the
Gradus Group. © 2016 Gradus Group LLC.
All Rights Reserved. GG2


Produkt Specifikationer

Mærke: Auray
Kategori: Ikke kategoriseret
Model: CFP-ET2

Har du brug for hjælp?

Hvis du har brug for hjælp til Auray CFP-ET2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Auray Manualer

Auray

Auray ABP-35N Manual

14 November 2024
Auray

Auray CFP-68R Manual

14 November 2024
Auray

Auray BA-LPR3 Manual

13 November 2024
Auray

Auray SB-52SSB Manual

9 November 2024
Auray

Auray RF-PBO Manual

26 August 2024
Auray

Auray CFC-610 Manual

26 August 2024
Auray

Auray COHH-FD1 Manual

26 August 2024
Auray

Auray RFDT-128 Manual

26 August 2024
Auray

Auray CFP-ET6 Manual

26 August 2024
Auray

Auray BP-59A Manual

26 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024