Aurora DT940C Manual

Aurora kalkulator DT940C

Læs nedenfor 📖 manual på dansk for Aurora DT940C (1 sider) i kategorien kalkulator. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

Size:L240*W200mm

：

Thank you for purchasing your new Aurora DT940C calculator,

please remove and recycle all packaging.

Instructions and FAQ’s:

1.Turning your calculator on and off.

2.What are the LOCAL and EURO keys for?

3.What is the switch marked for?

4.What is the switch marked for?

5.How do the memory keys work?

Storing a rate.

Converting an amount from £’s into Euros.

Converting an amount from Euros into £’s.

If we have £1000 how much is this in Euros? Clear the calculator then enter

1000 and press the EURO key, the amount of 1,428.57 will be displayed on

screen* along with a € symbol.

The amounts shown on the screen referred to above may vary depending

on your slide switch settings see below.

If we have 1000€ how much is this in £’s? Clear the calculator then enter

1000 and press the LOCAL key, the amount of 700.00 will be displayed on

the screen*.

You can set any two currencies you like into the calculator simply by

programming the relevant conversion rate.

This is the decimal place setting switch.

The ‘F’ stands for floating, your answer will not be shortened and will be

displayed using the largest amount of decimal places the screen permits

The ‘2’ fixes the number of decimal places to two; all answers will be

rounded to two decimal places based on the setting of your rounding switch

(see above).

The ‘0’ fixes the number of decimal places to zero, all answers will be

rounded to zero decimal places based on the setting of your rounding switch

IMPORTANT – the rounding and number of decimal places will be

affected by the setting of the decimal place switch see below.

This switch is the round up/down switch, there are 3 positions, the first is

marked with the arrow pointing upwards, on this setting the calculator will

round all answers up. The middle setting is marked 5/4, on this setting the

calculator will use the mathematical rule of rounding up when above 5 and

rounding down when below 5, the 3rd setting marked by the arrow pointing

down will round all answers down.

Your calculator has a memory and you can store a variable number, to store

a number press the ’M+’ key, you can store a simple number or an answer

from a calculation. The memory also has a running total, so you can add and

deduct numbers using the M+ and M- keys. To see the number stored in the

memory or the running total press the R.CM key once . To clear the memory

and reset back to zero press R.CM key twice or just press the CA key.

Aurora Electronics (UK) LTD.

Units 1&2 Shires Industrial Estate

Lichfield, Staffordshire WS14 9AZ

www.aurora-europe.co.uk

Example1 – Store the answers to the simple sums 2+2 and 3+3 in the

memory and calculate the total.

[Input 2, +, 2, M+, 3, +, 3, M+] press the R.CM key once, the correct answer

of 10 will be displayed.

Example 2 – Use the memory to add these number together; 5, -6, 8, 9, -4.

[Input 5, M+, 6, M-, 8, M+, 9, M+, 4, M-] press the R.CM key once the correct

answer 12 will be displayed. To clear and reset your memory press the R.CM

key twice or the CA key. Whenever a number is stored in the memory an ‘M’

will show on the display.

These buttons allow you to program a currency exchange rate and to easily

convert amounts from one currency to another.

Firstly you need to set a currency rate into the calculator which will be stored

in the memory until you change it even when the calculator turns off.

Let us assume you want to store a rate for converting between £’s and €’s.

We will use a rate of 1€ being equal to £0.70.

Firstly press the CA key to clear the calculator, then press the LOCAL key,

then enter 0.7, then press the LOCAL key again.

This rate is now set in the calculator. You can check the rate that is set by

pressing the CA key and then the EURO key, the rate that is currently set

will be displayed on the calculator screen.

To turn your calculator on simply press the red key.

The calculator is equipped with an ‘auto off’ feature and will power down by

itself after approx. 5 minutes of inactivity.

The CE on this key means clear entry, during a calculation pressing this key

once will remove you last entry but not your whole sum.

The C means cancel, during a calculation pressing this key twice will cancel

your whole calculation.

6.What does the CA key do?

7.What does the key do?

8.How do I change the battery?

9.My calculator has stopped working

– what should I do?

This is the Clear All key, pressing this clears the calculator of all calculations

and also clears the memory. It does not clear the currency exchange rate

which remains stored at your programmed rate.

This is the backspace or delete key, pressing this deletes the last digit you

entered.

If the screen of the calculator is fading or the calculator will not turn on then

it is likely the battery needs replacing (see above).

If you believe your calculator is faulty and you purchased it less than 1 year

ago then it is covered by a manufacturer’s warranty. Please contact your

supplier for details.

The calculator uses a single LR1130 battery which can be replaced.

On the back of the calculator there are 3 small screws, remove these and

keep safe.

The calculator case splits into two halves but it is held together inside by

plastic clips which need to be released, using a flat screwdriver on one of the

sides gently prise the case apart and run the screwdriver around the case to

release the clips. There are 7 in all, two on the top corners, two on both side

corners and one centrally on the bottom.

Now remove the back case, the battery is located in the battery holder that is

visible on the back of the circuit board in the front case. Gently slide the

battery out of the holder and replace. With the battery replaced reattached

the back case ensuring all the plastic clips are connected and replace the 3

screws.

(see above).

The ‘A’ stands for Add mode; here addition and subtraction functions are

performed with an automatic 2 digit decimal, this is useful when working with

currency as it speeds up data entry.

i.e. If you enter 1, 0, 0, 0 then press +, you will notice that the display shows

10.00, it assumes when you typed 1,0,0,0 you were entering 10.00 and not

1000.

Produkt Specifikationer

Mærke:	Aurora
Kategori:	kalkulator
Model:	DT940C

Har du brug for hjælp?

Hvis du har brug for hjælp til Aurora DT940C stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

kalkulator Aurora Manualer

21 August 2024

21 August 2024

21 August 2024

20 August 2024

20 August 2024

20 August 2024

20 August 2024

20 August 2024

20 August 2024

20 August 2024

kalkulator Manualer

Nyeste kalkulator Manualer

Sharp EL-W535B Manual

9 Oktober 2024

HP 39g+ Manual

4 Oktober 2024

Sharp EL-2196BL Manual

23 September 2024

Sharp EL-125A Manual

22 September 2024

Canon LS-85H Manual

22 September 2024

Sharp EL-6061H Manual

19 September 2024

Calculated Industries Construction Master Plus EZ Manual

15 September 2024

Calculated Industries Construction Master Pro DT Manual

15 September 2024

Citizen 107DP Manual

12 September 2024

Sharp EL-W535X Manual

8 September 2024