AXESS AX-ADDCAM-CH6 Manual

AXESS Ikke kategoriseret AX-ADDCAM-CH6

Læs nedenfor 📖 manual på dansk for AXESS AX-ADDCAM-CH6 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
AX-ADDCAM-CH6
INS TALL ATIO N IN STR UCT ION S
REV. 7/11/18© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
Integrate • AxxessInterfaces.com
  •  Control 1 - Gray/Blue wire
  •  Control 2 - Gray/Red wire
  •  Control 3 -   wireOrange
  •  Control 4 - Orange/White wire
Fiat Family 2015-up*
INTERFACE FEATURES
• “Plug & Play” harness for the AX-ADDCAM interface (sold separately)
• 
Reverse signal trigger generated via CAN bus communication of the vehicle
• 
Turn signal trigger generated via CAN bus communication of the vehicle
• (4) Programmable camera control wires (configured through the 
Axxess Updater program)
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun, solder, and heat shrink
• Tape • Wire cutter • Zip ties
CONNECTIONS
•  For vehicles
with
a factory camera:  The camera signal will need to be 
interrupted and connected to the corresponding input/output RCA jacks 
on the AX-ADDCAM interface.
• 
Connect the RCA jack from the AX-ADDCAM-CH6 labeled “Camera 
output”, to the RCA jack on the AX-ADDCAM interface labeled “Camera 1”.
• 
Connect the RCA jack from the AX-ADDCAM-CH6 labeled “Camera input”, 
to the RCA jack on the AX-ADDCAM interface labeled “Camera output”.
•  For vehicles
without
a factory camera:
•  Connect the RCA jack on the AX-ADDCAM-CH6 labeled “Camera input”, to 
the RCA jack on the AX-ADDCAM interface labeled “Camera output”.
•  Disregard the RCA jack labeled “Camera output”, it will not be used in 
this application. 
• 
Disregard the following (2) wires, they will not be used in this application:
Blue/Green
 labeled “VSS input”, 
Green/Red
 labeled “VSS output”
ANALOG CONTROL TRIGGER WIRES
•  The optional analog control wires can be activated with either a negative 
or positive trigger depending on how they are configured in the Axxess
Updater program. These wires will only be used if manual control of the 
cameras will be desired. Otherwise tape off and disregard these wires.
*Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
INSTALLATION
•  Configure the AX-ADDCAM interface following the installation instructions 
included with the AX-ADDCAM interface. Failure to configure the interface 
will result in the interface not functioning properly.
•  Remove the main harness from the factory radio, then install the 
AX-ADDCAM-CH6 in between.


Produkt Specifikationer

Mærke: AXESS
Kategori: Ikke kategoriseret
Model: AX-ADDCAM-CH6

Har du brug for hjælp?

Hvis du har brug for hjælp til AXESS AX-ADDCAM-CH6 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret AXESS Manualer

AXESS

AXESS 99-6520B Manual

10 September 2024
AXESS

AXESS AXPIO-IN1 Manual

10 September 2024
AXESS

AXESS AXBUCS-MZ286V Manual

9 September 2024
AXESS

AXESS 99-7014HG Manual

6 September 2024
AXESS

AXESS AXGM-17 Manual

6 September 2024
AXESS

AXESS AXGMLN-34 Manual

6 September 2024
AXESS

AXESS 99-7382HG Manual

6 September 2024
AXESS

AXESS GMOS-12 Manual

6 September 2024
AXESS

AXESS XSVI-1788-NAV Manual

6 September 2024
AXESS

AXESS 99-7510HG Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024