Bauhn ATAPB-0224 Manual

Bauhn power bank ATAPB-0224

Læs nedenfor 📖 manual på dansk for Bauhn ATAPB-0224 (2 sider) i kategorien power bank. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
C
D
Outputs
Control and Buttons
Have you got everything?
A. Kickstand retracted
B. Kickstand extended
C. USB-C Cable
D. Lightning Cable
E. Lanyard Attachment
F. On/Off Button
Travel Adaptor
Power Bank
A. Travel Adapter Power Bank
B. 4 x Travel plug adapters
C. User Guide
D. Warranty Certicate
E. Travel Kit
F. Carry Strap
User Guide
Model: ATAPB-0224
Travel Adaptor Power Bank
A
F
L
G. LED Display (battery capacity)
H. LED Indicator (power bank status)
I. USB-C input/output
J. USB-A output
K. AC input Plug
L. Wireless Charging
Operation
Power on/off
Press the power button to turn on the power bank, the LED display
will light up and show the remaining power.
Press the power button twice to turn off the power bank.
Charging your devices
Unfold the USB cable (attached), either USB-C or lightning cable
and connect to the port on your device.
You can also use a separate USB-A or USB-C cable (not included) to
charge your mobile devices.
The LED display shows the power remaining as a percentage from
0%-100%. When the remaining power drops lower than 5%, the LED
display starts blinking to display the low power warning.
When the USB-A or USB-C fast charging mode is activated, the LED
indicator will light up red.
When charging multiple devices at same time, the power bank will
exit fast charging mode and it will share charging power to your
connected devices. The red LED indicator will turn off.
Wireless Charging:
When the power bank is switched on, the
LED indicator will light up green which
indicates the wireless charging function is
activated.
Place your smart phone facing up on the wireless charging pad. Make
sure your phone is correctly aligned and has started charging.
Note: If the LED indicator is not green, the power bank may have
entered protection mode. This is due to other devices being
connected to USB-A or USB-C ports in fast charging mode. Press the
power button to quit that fast charging mode to activate the wireless
charging.
If the LED indicator is ashing green, this means an error has occurred.
Either the smart phone does not support wireless charging or other
objects are obstructing the wireless charging pad.
Note: The power bank will automatically quit the wireless charging
mode in 30s to save power if the wireless charging load is too low.
Press the power button again to activate the wireless charging
function.
Charging your power bank
Plug the travel adapter power bank into either mains power or the
USB-C input until fully charged.
Charge for 3-5 hours to fully charge the power bank before use.
Note: Charging time is about 3 hours when using USB-C fast charging
input. It is about 5 hours when using mains power input.
When the USB-C fast charging input activated, the LED indicator
will light red.
If you connect devices to the power bank while it is charging. Power
will be shared and charging time will be extended.
A
Charging
Discharging
Inputs
AC Input USB-C Input
USB-A Output USB-C Output
USB-C Cable Output Lightning Cable Output
C
B
B
B
B
B
E G I J K
B
Install the travel adaptor
plug and slide onto the pins
located at the corner of the
Power bank.
Gently push and slide to
remove and change plugs
FE
D
H
Wireless Output


Produkt Specifikationer

Mærke: Bauhn
Kategori: power bank
Model: ATAPB-0224

Har du brug for hjælp?

Hvis du har brug for hjælp til Bauhn ATAPB-0224 stil et spørgsmål nedenfor, og andre brugere vil svare dig




power bank Bauhn Manualer

Bauhn

Bauhn ATAPB-0224 Manual

15 Oktober 2024

power bank Manualer

Nyeste power bank Manualer