Bauknecht B7I HF60 TUSC CH Manual

Bauknecht Opvaskemaskine B7I HF60 TUSC CH

Læs nedenfor 📖 manual på dansk for Bauknecht B7I HF60 TUSC CH (28 sider) i kategorien Opvaskemaskine. Denne guide var nyttig for 19 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/28
ENDaily Reference Guide
1
THANK YOU FOR BUYING A BAUKNECHT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.bauknecht.eu/register
4 5 6 7 8 9 10 13 14 1511 12 16 17 18 191 2 3 20 21 22
1. ON-OFF/Reset button with indicator light
2. Eco program button with indicator light
3. Auto Intensive program button with indicator light
4. Auto Mixed program button with indicator light
5. Auto Fast program button with indicator light
6. Rapid program button with indicator light
7. Glass
program button with indicator light/ - 3 sec. pressSelf-Clean program
8. Prewash program button with indicator light
9. Salt reservoir empty indicator light
10. Rinse Aid reservoir empty indicator light
11. Display
12. Program number remaining time and indicator
13. Closed water tap indicator light
14. DESCALE indicator light
15. Power Clean® option button with indicator light
16. Half Load option button with indicator light
17. Extra Dry option Settings button with indicator light/ - 3 sec. press
18. Silent option button with indicator light
19. Sani Rinse option button with indicator light
20. Turbo option button with indicator light
21. Delay option button with indicator light
22. START/Pause button with indicator light
SETTING MENU
1. Switch on the appliance by pressing the button.ON-OFF
2. Hold the Settings (Extra Dry ) button for 3 seconds, until you hear
a beep and the display shows .SEt
3. After one second the rst available setting (letter ) will be displayed.h
4. Press Prewash program / Power Clean® option buttons to scroll
through the list of available settings (see table below), then press START/
Pause to view and change the value of currently selected setting.
5. Press Prewash program Power Clean® option /
buttons
to
change the value, then press START/Pause to save the new value.
6. To change another setting, repeat points 2 and 5.
7. Press or wait 30 seconds to exit the menu.ON-OFF
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
It is mandatory that the salt reservoir never be empty.
It is important to set the water hardness.
Salt must be lled when the SALT REFILL indicator light on the con-
trol panel is lit.1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel and ll the salt reservoir (see gure)
right up to its edge (approximately 0,5 kg); it is not un-
usual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
LETTER SETTING VALUES
(Default - )in bold
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”) 1 | 2 | | 4 | 53
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”)
0 | 1 | 2 | 3 |
4 | 5
ActiveDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Time on the oor (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Sound
“1” = On, “0” = O 1 | 0
Internal Lights (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included in
the settings menu.
-
Setting the water hardness
To allow the water softener to work in a perfect way, it is essential that the water
hardness setting is based on the actual water hardness in your house. This infor-
mation can be obtained from your local water supplier. The factory setting is 3.
See WATER HARDNESS TABLE.
To change, follow instructions in section “SETTING MENU.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing
scale buildup on the heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
the salt container when empty. The frequency of regeneration depends
on the water hardness level setting - regeneration takes place once per 4-6
Eco cycles with the water hardness level set to . During runs with regenera3-
tion, additional water management system ll will happen. The regeneration
and water management process occurs at the beginning of the cycle with
additional fresh water.
Single regeneration consumes ~6,5L of water;
Takes up to 5 additional minutes for the cycle;
Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser should be lled A
when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.
110 ml), making sure it does
not overow from the dis-
penser. If this happens, clean
the spill immediately with a
dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (Soft) 0 - 6 0 - 10 0 - 7
2 (Medium) 7 - 11 11 - 20 8 - 14
3 (Average) 12 - 16 21 - 29 15 - 20
4 (Hard) 17 - 34 30 - 60 21 - 42
5 (Very hard) 35 - 50 61 - 90 43 - 62
A
B
Before using the appliance carefully read
Safety and Installation Instructions. More information about your
product available on website: docs.bauknecht.eu
After installation, please remember to remove all transport protection
parts from the dishwasher.
CONTROL PANEL
FIRST TIME USE
DISPLAY ON THE FLOOR
1
3
2
1. Delay Time on the oor - indicator of the time left to the start of the cycle, when the Delay option is set
2. Salt reservoir empty - indicator light on the oor
3. Remaining Time on the oor - indicator of the time left to the end of the cycle


Produkt Specifikationer

Mærke: Bauknecht
Kategori: Opvaskemaskine
Model: B7I HF60 TUSC CH

Har du brug for hjælp?

Hvis du har brug for hjælp til Bauknecht B7I HF60 TUSC CH stil et spørgsmål nedenfor, og andre brugere vil svare dig




Opvaskemaskine Bauknecht Manualer

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Arçelik

Arçelik 6467 WF I Manual

24 December 2024
Bosch

Bosch SMV4ECX30E Manual

24 December 2024
Smeg

Smeg ST3339L Manual

23 December 2024
Miele

Miele G 6415 SCI XXL Manual

23 December 2024
Miele

Miele G 5830 SCi Manual

23 December 2024
Miele

Miele G 4220 Manual

23 December 2024
Miele

Miele G 6920 SCi Manual

23 December 2024
Miele

Miele G 4300 Manual

23 December 2024
Miele

Miele G 5164 SC Vi Manual

23 December 2024