Behringer 992 Manual


Læs nedenfor 📖 manual på dansk for Behringer 992 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 2 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Quick Start Guide
992 CONTROL VOLTAGES
Legendary Analog CV Routing
Module for Eurorack
Controls
(1) CV Switches – Allow the voltage or signal from the
associated input to be sent to the output jacks when the
switch is in the up position. The input is disconnected
when the switch is in the down position.
(2) EXT INPUT – Additional input to be used with the signal-
inverting attenuator circuit.
(3) Attenuator Knob - Turn clockwise to adjust the CV level
from 0 to 10 (unity gain). Turn counterclockwise to invert
the signal from 0 to -10, which is also unity gain. At the
center 0 position, the signal is o (-∞).
(4) CONTROL INPUTS – Connect control voltages from other
modules via 3.5 mm TS cable.
(5) FREQUENCY CONTROL TO LPF Send the combined
voltage from all 4 inputs to up to 3 modules via
3.5 mm TS cable.
Power Connection
The 992 comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series ofxed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow
small adjustments to the positioning while you get them all
aligned. After the nal position has been established, tighten the
screws down.
(1)
(4)
(5)
(2) (3)


Produkt Specifikationer

Mærke: Behringer
Kategori: Ikke kategoriseret
Model: 992

Har du brug for hjælp?

Hvis du har brug for hjælp til Behringer 992 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Behringer Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Gigabyte

Gigabyte ODIN GT 550W Manual

23 November 2024
Stamos

Stamos S-PLASMA 60U Manual

23 November 2024
Velbus

Velbus VMBPIRO-W-20 Manual

23 November 2024
Honor

Honor 90 Pro Manual

23 November 2024
Honor

Honor 80 SE Manual

23 November 2024
Medela

Medela Safe & Dry Manual

22 November 2024
Jane

Jane First Potty Manual

22 November 2024