Behringer PP400 Manual


Læs nedenfor 📖 manual på dansk for Behringer PP400 (2 sider) i kategorien Modtager. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
MICROPHONO PP400
Welcome to BEHRINGER
Thank you for showing your condence in us by purchasing the BEHRINGER MICROPHONO
PP400, a compact phono preamplier.
Turntables have low-level signals. However, most audio units can only process line-level
signals. Between a turntable and another audio unit (a mixer, an amplier, or a recording
unit), the PP400 acts as an intermediary, as follows:
1. The PP400 equalizes a turntable signal according to RIAA specications.
2. The PP400 amplies the RIAA equalized signal.
3. The PP400 outputs a line-level signal.
Please read the safety instructions that appear at the end of this document.
Connectors and Control Elements
This section illustrates and describes each PP400 connector and control element.
(2)
(1) (5)(3) (4)
Fig. 1: PP400 connectors and control elements
(1) 12 V𝌂 connector:
To connect the power supply unit to the PP400, use the 12 V connector. Connecting the
power supply unit to the mains automatically switches the PP400 on. To disconnect
the unit from the mains, pull out the main cord plug.
(2) ON LED:
As soon as the unit is connected to the mains, the ON LED is illuminated.
(3) INPUT ( and ) connectors: L R
To send a turntable signal to the PP400, you need an RCA audio cable (stereo). Use this
cable to connect:
• the output on the turntable to the (left) INPUT on the PP400 left L
• the output on the turntable to the (right) INPUT on the PP400right R
The PP400 can output a line-level signal via one of the following connectors:
• RCA ((4) OUTPUT L and R)
• ¼” TRS ((5) OUTPUT)
Do not simultaneously use both PP400 OUTPUTs.
(4) OUTPUT ( and ) connectors: L R
To use these RCA connectors, you need an RCA audio cable (stereo). Use this audio
cable to connect:
• the (left) OUTPUT on the PP400 to the input on the amplier, L left
recordingunit, or mixer. (On a mixer, use a CD or TAPE input.)
• the (right) OUTPUT on the PP400 to the input on the amplier, R right
recordingunit, or mixer
(5) OUTPUT connector:
To use this ¼”, TRS (stereo) connector, you need an audio cable. Use the audio cable
to connect the PP400 OUTPUT to an input on the mixer, amplier, or recording unit.
Oneend of this audio cable must include a ¼”, TRS connector. If the input on the mixer,
amplier, or recording unit is:
• stereo, the other end of the audio cable must include a ¼”, TRS connector
• mono, the other end of the audio cable must include 2 TS connectors
(one for each mono input)
SERIAL NUMBER: To register your unit, use the serial number that is located on the bottom
of the PP400.
Setup Example
The following is an example of how to set up the PP400:
OUTPUT
TAPE IN/STREREO
CHANNEL IN
TURNTABLE UB1204-PRO
MICROPHONO PP400
INPUT
Fig 2: PP400 setup example


Produkt Specifikationer

Mærke: Behringer
Kategori: Modtager
Model: PP400

Har du brug for hjælp?

Hvis du har brug for hjælp til Behringer PP400 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Modtager Behringer Manualer

Modtager Manualer

Nyeste Modtager Manualer

DAP-Audio

DAP-Audio TA-4.3400 Manual

21 December 2024
JBL

JBL Power P7520 Manual

20 December 2024
JBL

JBL Power P-2510 Manual

20 December 2024
Devialet

Devialet Astra Dual Manual

19 December 2024
Devialet

Devialet Astra Manual

19 December 2024
QSC

QSC PL236 Manual

19 December 2024
QSC

QSC PL218 Manual

19 December 2024
QSC

QSC PL224 Manual

19 December 2024
QSC

QSC PL230 Manual

19 December 2024