Bestway Power Steel 561EJ Manual
Bestway
Over jorden swimmingpool
Power Steel 561EJ
Læs nedenfor 📖 manual på dansk for Bestway Power Steel 561EJ (144 sider) i kategorien Over jorden swimmingpool. Denne guide var nyttig for 19 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/144
©2022 Bestway Inflatables & Material Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/
Alle Rechte vorbehalten/Tutti i diritti riservati
Trademarks used in some countries under license from/
Marques utilisées dans certains pays sous la licence de/
Marcas comerciales utilizadas en algunos países bajo la licencia de/
Die Warenzeichen werden in einigen Ländern verwendet unter Lizenz der/
Marchi utilizzati in alcuni paesi concessi in licenza a
Bestway Inflatables & Material Corp., Shanghai, China
Manufactured, distributed and represented in the European Union by/
Fabriqués, distribués et représentés dans l’Union Européenne par/Fabricado, distribuido y representado en la Unión Europea por/
Hergestellt, vertrieben und in der Europäischen Union vertreten von/Prodotto, distribuito e rappresentato nell'Unione Europea da
Bestway Europe S.p.a., Via Resistenza, 5, 20098 San Giuliano Milanese (Milano), Italy
Distributed in Latin America by/Distribué en Amérique latine par/Distribuido en Latinoamérica por/Distribuído na América Latina por
Bestway Central & South America Ltda, Salar Ascotan 1282, Parque Enea, Pudahuel, Santiago, Chile
Distributed in Australia & New Zealand by Bestway Australia Pty Ltd, Unit 2/98-104 Carnarvon St Silverwater, NSW 2128, Australia
Tel: Australia: (+61) 2 9037 1388; New Zealand: 0800 142 101
Distributed in United Kingdom by Bestway Corp UK Ltd. 8 Wentworth Road, Heathfield Industrial Estate, Newton Abbot, Devon, TQ12 6TL
Exported by/Exporté par/Exportado por/Exportiert von/Esportato da
Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited
Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong
www.bestwaycorp.com
EN
PT
ES
DE
FI
NL
IT
FR
EL
RU
PL
HU
SV
EN
Visit the Bestway YouTube channel
OWNER’S MANUAL
58497 Hmax 1.5 m Sand Filter
2
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW
ALL SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
When installing and using this electrical equipment, basic safety
precautions should always be followed, including the following:
• The pump is to be supplied by an isolating transformer or
supplied through a residual current device (RCD) having a rated
residual operating current not exceeding 30 mA.
• The power source on the wall of building should keep more than
4m away from pool.
• The appliance must be supplied by earthed power source.
• - The pump cannot be using while RISK OF ELECTRIC SHOCK
people are inside the pool. Forbid the access of the pool in case
of damage of the sand filter.
• Locate cord to minimize abuse from DO NOT BURY CORD.
lawn mowers, hedge trimmers, and other equipment.
• To reduce the risk of electric shock, replace damaged cord
immediately.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
• Extension cords can’t be used.
• Risk of electric shock. Using the sand filter with an unmatched
electrical supply is dangerous and will permanently damage the
sand filter.
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
Fo Q, Manu , idr FA als V eos r O
Spare arts ease P , Pl Visit
bestwaycorp.com/support
V
i
s
i
t
w
w
w
.
b
e
s
t
w
a
y
c
o
r
p
.
c
o
m
/
s
u
p
p
o
r
t
f
o
r
h
e
l
p
3
• Do not remove the grounding prong or modify the plug in
anyway. Do not use adaptor plugs. Consult a qualified electrician
for any questions relating to validity of your plugs or grounding.
• Handle the sand filter with care. Do not pull or carry the sand
filter by the power cord. Never pull a plug from the outlet by
yanking the power cord. Keep cord free from abrasions. Sharp
objects, oil, moving parts, and heat should never be exposed to
the sand filter.
•
Always unplug this product from the electrical outlet before removing,
cleaning, servicing or making any adjustment to the product.
• Don’t plug or unplug the appliance if hand is wet.
• Always unplug the appliance:
• On raining days
• Before cleaning or other maintenance
• Leave it unattended on holidays
• When the appliance will be not used for long time, such as in the
winter, the pool set should be disassembled and stored indoor.
• Read the instruction before using the appliance and CAUTION:
installation/reassembly every time.
• Safekeeping the instruction. For reconstruction the pool set every
time, please always refer to the instructions.
• If instruction is missed, please contact with Bestway or search it
in website: www.bestwaycorp.com
• Electric installations should follow national wiring rules. Consult a
qualified electrician for any questions.
CAUTION: This sand filter is for use with storable pools only. Do
not use with permanently-installed pools. A storable pool is
constructed so that it is capable of being readily disassembled for
storage and reassembled to its original integrity. A permanently-installed
pool is constructed in or on the ground or in a building such that it
cannot be readily disassembled for storage.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
• Cleaning and user maintenance must be performed by an adult
above 18 years old who is familiar with the risk of electric shock.
NOTES:
• Place the sand filter on solid, level ground. Ensure the sand filter
is at least 2 meters away from poolside. Keep distance as far as
possible.
• Pay attention to position pool and sand filter so adequate
ventilation, drainage, and access for maintenance is available.
Never place the sand filter in an area that may accumulate water,
or on a walking path with lots of foot traffic.
• It is necessary to have the plug accessible after installation of the
pool. The plug of the sand filter shall be at least 3.5m away from
the pool.
• Atmospheric conditions may affect the performance and life span
of the sand filter; take adequate precautions to protect the sand
filter from unnecessary wear and tear that may occur during
periods of cold or hot weather and/or exposure to sun.
• Please examine and verify all sand filter components are present
before use. Notify Bestway at the customer service address listed
on this manual for any damaged or missing parts at the time of
purchase.
• It is imperative to change as soon as possible all deteriorated
parts. Only use parts approved by the manufacturer.
• Do not allow children or adults to lean or sit on the apparatus.
• Do not add chemicals to the sand filter.
• When chemical products are used to clean the pool water, it is
recommended to respect a minimum filtration time to preserve
the health of swimmers which depends on compliance of health
regulation.
• Only the media provided or specified by the manufacturer is to
4
SPECIFICATIONS
Before assembling the sand filter, take a few minutes to become familiar with all the sand filter parts.
6
PARTS REFERENCE OVERVIEW
Filter Diameter:
Effective Filter Area:
Max. Operating Pressure:
Working sand filter pressure:
Max. Water Temperature:
Sand:
Sand Size:
Sand Capacity:
254 mm
0.05 m2(0.54 ft2)
0.83 Bar(12 PSI)
<0.45 Bar(6.5 PSI)
35°C
Not included
#20 silica sand,0.45-0.85 mm
Approximately 9 kg
A
D
520mm
476mm
254mm
MAX
MIN
A
B
C
A
x1
x1
x2
x1
x1
x1
x1
x1
x1
x1
x1
x5
x1
x1
x1
x1
x2
x2
x1
x1
x1
x1
x1
x1
x2
x1
x1
B
x1
x1
x2
x1
x1
x1
x1
x1
x1
x1
x1
x5
x1
x1
x1
x1
x0
x0
x1
x1
x1
x1
x1
x1
x2
x0
x0
C
x1
x1
x2
x1
x1
x1
x1
x1
x1
x1
x1
x5
x1
x1
x1
x1
x0
x0
x1
x1
x1
x1
x1
x1
x2
x0
x0
2524
10
15
12
12
23
22
21
20
19
18
17
1611
12
13
14
9
8 7
6
5
4
3
2
1
-126
26
-226 -1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
26 -2
x2
x2
x2 x1 x1
REF.NO
7
LOAD POOL-GRADE FILTER SAND/FLOWCLEAR™ POLYSPHERE.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85 mm, approximately one 9 kg bag
should suffice.
If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, thereby
voiding the warranty.
IMPORTANT:
We suggest using #20 silica sand with your pool sand filter. It is specially graded to trap particles in the 20 - 100 micron range.
Some small debris can pass throw the sand and back into the pool. This is normal, especially if the debris is fine or silt.
To limit this, it is better to follow the maintenance instructions, and backwash and rinse when necessary.
We also suggest contacting your pool dealer for the chemical product specifically made to clean the sand. The correct maintenance of
the sand will optimize the cleaning efficiency and avoid accumulation of oils or scale.
When you are vacuuming the bottom of the pool that has a large amount of debris, we suggest to backwash the sand when you finish
cleaning half of the pool.
Remember to backwash and rinse the sand after vacuuming the bottom of the pool each time.
NOTE:
To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the Hub.
NOTE: Sand/Flowclear™ Polysphere not included.
NOTE: Use 28 g (0.06 lbs) Flowclear™ Polysphere to replace 1 kg (2.20 lbs) sand.
(You will need a screwdriver.)
ASSEMBLY
1. Carefully remove all components from the package and check to ensure nothing
is damaged. If equipment is damaged, immediately notify the retailer from where the
equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab.
Position the sand filter so the Ports and Control Valve are accessible for operation,
servicing and winterizing.
3. EN60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground
or a certain pedestal made of wood or concrete before use to prevent the sand filter
from accidentally falling. Fully assembled sand filter will exceed 18 kg. The mounting
holes should be 8 mm in diameter and Uspaced 86 mm apart. se two bolts and nuts
with a maximum of 8 mm in diameter to fasten the sand filter to the pedestal.
Bestway
86mm Φ8
1
4
78
56
23
c
D
c
c
c
c
c
#20
0.45-0.85 mm
MAX
MIN
MAX
MIN
AB
A
B
A
B
D
C
A
B
8
A
A
A
A
B
B
A
B
B
D
C
A
B
CONNECT TO THE POOL
V1.1
V1.2
V2
D
C
A
B
B
A
D
Garden hose
(not included)
For Drain,
Backwash,
Rinse function
D
D
D
D
(1)
(2)
(3)
9
Before powering on, please read the manual carefully.
TIMER
1. Plug into power source, turn the nob to the desired position. The sand filter will begin working immediately.
2. Turn the nob on the “0” position. The sand filter will stop working immediately.
3. After turning on, you can adjust work time, rest time and cycle time by turning the knob to desired position. See the table
below for more details.
4.
When the timer knob is moved into new position, the filter’s previous cycle automatically cancels so new cycle can begin.
5. Each time the filter is powered on or restarted, a new cycle will begin based on timer knob position.
NOTE: If the knob is adjusted to the 24-hour position (24), the sand filter will work continuously without any rest period.
AB
26-1
26-2
c
D
FOR POOL WITH 32 MM (1.25 IN.) VALVE
STOP
OPERATION
CONTROL VALVE OVERVIEW
WARNING: To prevent equipment damage and possible injury,
always switch off sand filter before changing the Control Valve
function. Changing valve positions while the pump is running can
damage the Control Valve, which may cause personal injury or
property damage.
How to Use the Control Valve:
Press down on the Control Valve handle and rotate to
desired function.
CONTROL VALVE FUNCTIONS
The Control valve is used to select 6 different filter
functions: Filter, Closed Backwash, Rinse, Drain and ,
Circulate.
Knob Position
0
6
8
10
12
24
P4
P6
P8
Working time(H)
/
6
8
10
12
24
4
6
8
Rest time(H)
/
18
16
14
12
0
4
6
8
Cycle period(H)
/
24
24
24
24
24
8
12
16
D
A
C
Bestway
10
B
C
A
C
B
A
C
B
A
D
C
B
D
A
C
B
D
AC
B
A
Filter: This function is used to filter
pool water and should be positioned
here 99% of the time. Water is pumped
through the sand filter, where it is
cleaned and returned to the pool.
Closed: This function stops water
flowing between the sand filter and
the pool.
Backwash: This function is used to
clean the sand bed; water is pumped
down through the Collector Hub,
upwards through the sand bed, and
deposited out of Port D.
Rinse: This function for initial startup,
cleaning, and sand bed leveling after
Backwash; water is pumped downwards
through the sand bed, up through the
Collector Hub and deposited out of the
valve Port D.
Drain: This function drains water from
the pool; another filter bypass setting,
water is pumped and deposited out of
Port D, instead of returning it to the pool.
Circulate: This function circulates pool
water bypassing the sand filter; use this
function if the filter is broken to collect
debris in the Debris Screens.
11
NOTE:
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water
where it will cause flooding or damage.
•
When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
•
Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
AIR RELEASE
Press down the control valve handle and wait untill the water flow from Port D to release the air.
NOTE:
It is important to repeat this operation every time you start the pump after winterizing, maintenance and backwashing
the
sand bed.
FIRST TIME USE INSTRUCTIONS
Backwash and Rinsing must be performed to prepare the pump for its first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Plug in and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates
water backwards through the sand filter and drains water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water if required.
IMPORTANT:
This procedure removes water from the pool, which you’ll need to replace. Switch off the sand filter immediately
if water levels near the pool’s Inlet and Outlet valves.
Backwash Rinsing
1.6
0
5
10 15
20
23
1.4
1.2
1
0.8
0.6
0.4
0.2
0
psi
bar
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of electrical shock
dry any excess water from yourself and the
sand filter.
2. Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning
to the pool and take note of the filter pressure on Pressure Gauge. Generally, the
recommended sand filter pressure is less than 0.45 Bar (6.5 PSI) when it is running.
CAUTION:
You must ensure the sand filter
is switched off and unplugged before any
maintenance begins or severe risk of injury
or death exists.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will
increase. When the Pressure Gauge is 0.45 Bar (6.5 PSI) or higher, or water flow
to the pool is too low, it is time to clean the sand. To clean the sand bed, follow
all instructions outlined previously in: Backwash and Rinsing.
NOTE: Pressure gauge is for maintenance purpose only, and the pressure
gauge value is just for reference, it should not be used as a precision instrument.
NOTE: We recommend you clean the sand bed once a month or less regularly
depending on how often the pool is used. Do not clean the sand too frequently.
SAND FILTER MAINTENANCE
CLEANING THE STRAINER
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Close the connection valves.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Open the connection valves.
NOTE: The Strainer must be emptied and cleaned periodically. A dirty or blocked
strainer will reduce the performance of the sand filter.
12
1. Backwash the sand filter.
2. Detach the Hose from the pool’s Port A and sand filter Port A and attach to Port D.
NOTE: Remember to replace the Debris Screen with Stopper Plug to prevent water from escaping.
3. Switch on the sand filter to remove pool water.
WARNING: DO NOT DRY RUN THE SAND FILTER.
Problems Probable Causes Solutions
Sand is flowing
to the pool
No water flow
Excessive filter
pressure
Control Valve leaks
from the port D
Connectors leak
- Sand is too small
- Move the control valve from the backwash to
the filter function without stop the sand filter
- The level of the sand is too high
- The skimmer is broken
- Stopper plugs were not removed
- Air was not released
- The control valve is set to Closed
- The strainer is blocked
- Sand filter broken
- Dirty filter
- Calcified sand bed
- Insufficient backwashing
- The pressure gauge is broken
- Control Valve is set between two functions
- The gasket is broken
- Washer of the connectors not in place
- Washer of the connectors broken
- Loose Hoses
- Recommend 0.45 mm to 0.85 mm #20 silica sand
- Stop the sand filter every time set the control valve
- Check if the level of the sand is between the
marked “MAX” and “ MIN” on the collector hub
- Replace the skimmer
- Remove the stopper plugs and insert the debris
screens
- Release the air
- Set to filter function
- Clean the strainer
- Call for service
- Backwash
- Inspect sand and change if necessary
- Backwash until water runs clear
- Replace the pressure gauge
- Set to one function
- Replace the gasket
- Reposition the washer
- Replace the washer
- Tighten them
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing
water to freeze will damage the sand filter and void warranty.
1. Backwash the sand filter.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
LOWERING OR DRAINING POOL WATER
STORAGE
TROUBLESHOOTING
PT
13
ATENÇÃO
INSTRUÇÕES DE SEGURANÇA IMPORTANTES LEIA E SIGA TODAS AS
INSTRUÇÕES DE SEGURANÇA.
Ao instalar e usar este equipamento elétrico, as precauções básicas de
segurança devem ser sempre seguidas, incluindo aquelas citadas a seguir:
• A bomba deve ser equipada com um transformador isolante ou alimentada
através de um dispositivo de corrente residual (RCD) com uma tensão de
funcionamento residual classificada que não exceda 30 mA.
• A fonte de alimentação na parede do edifício deve estar a mais de 4m de
distância da piscina.
• O equipamento deve ser equipado com uma fonte de alimentação com
ligação a terra.
• A bomba não pode ser utilizada enquanto RISCO DE CHOQUE ELÉTRICO -
estiverem pessoas no interior da piscina. Proíba o acesso à piscina caso o
filtro de areia se encontre danificado.
• Coloque o fio de modo a evitar danos causados NÃO ENTERRAR O FIO.
por cortadores de gramas, aparadores e outros equipamentos.
• Para reduzir o risco de choque elétrico, substitua imediatamente o fio
danificado.
• Se o fio de alimentação estiver danificado, ele deve ser substituído pelo
fabricante, pelo seu agente de serviço ou por pessoas igualmente
qualificadas de modo a evitar um dano.
• É proibido o uso de extensões de alimentação.
• Risco de choque elétrico. Usando o filtro de areia em uma fonte elétrica não
correspondente é perigoso e danificará permanentemente o filtro de areia.
INSTRUÇÕES DE SEGURANÇA
Visite o canal YouTube da Bestway
MANUAL DO PROPRIETÁRIO
Filtro de Areia 58497 Hmax 1,5 m
RECOMENDAMOS NÃO DEVOLVER
O PRODUTO PARA A LOJA
Dúvidas? Problemas?
Faltam peças?
Para FAQ, manuais, vídeos ou
peças de reposição, visite
bestwaycorp.com/support
S
e
p
r
e
c
i
s
a
d
e
a
j
u
d
a
,
v
i
s
i
t
e
w
w
w
.
b
e
s
t
w
a
y
c
o
r
p
.
c
o
m
/
s
u
p
p
o
r
t
15
de experiência e conhecimento caso estes recebam supervisão ou instrução
sobre o uso do equipamento de forma segura e compreendam os ricos
envolvidos. As crianças não devem brincar com o aparelho. A limpeza e
manutenção por parte do utilizador não deve ser realizada por crianças sem
supervisão.
• A limpeza e manutenção devem ser realizadas por um adulto com idade
superior a 18 anos e que tenha consciência do risco de choque eléctrico.
NOTA:
• Coloque o filtro de areia em um apoio sólido e nivelado. Favor certificar-se
que o filtro de areia está a pelo menos 2 metros afastado da piscina.
Mantenha a distância, tanto quanto possível.
• Preste AVISO ao posicionar a piscina e o filtro de areia de modo a ter uma
ventilação e drenagem adequadas e acesso disponível para a limpeza.
Nunca coloque o filtro de areia em uma área que possa acumular água ou
que os movimentos dentro da piscina faça com que a água transborde.
• É necessário ter a tomada acessível após a instalação da piscina A tomada
do filtro de areia deve estar a pelo menos 3,5m afastado da piscina.
• As condições atmosféricas podem afetar o desempenho e a vida útil do filtro
de areia; tome precauções adequadas para proteger o filtro de areia do
desgaste e usura desnecessários que podem ocorrer em períodos de frio ou
calor e/ou exposição ao sol.
• Por favor examine e verifique todos se todos componentes estão presentes
antes de usá-los. Notifique à Bestway, por meio dos endereços de
assistência ao cliente aqui elencados neste manual, se houver peças
danificados ou faltando no momento da compra.
• É fundamental que todos os componentes deteriorados sejam substituídos o
mais rápido possível. Utilize apenas componentes aprovados pelo
fabricante.
• Não permite que crianças ou adultos se apóie ou sentem no aparato.
• Não adicione produtos químicos ao filtro de areia.
• Quando forem utilizados produtos químicos para limpar a água da piscina,
recomenda-se que respeite o tempo de filtragem mínima, de acordo com as
normas de saúde locais, para proteger a saúde dos utilizadores.
• Apenas os meios fornecidos ou especificados pelo fabricante devem ser
18
MONTAGEM
(Você irá precisar de
uma chave de fendas.)
1.
Remova cuidadosamente todos os componentes da embalagem e verifique que cada tenha
sido danificado. Se o equipamento estiver danificado, notifique imediatamente o revendedor do
estabelecimento onde o equipamento foi comprado.
2. O filtro de areia deve ser colocado em um lugar sólido, nivelado e de preferência em uma
base de
concreto. Posicione o filtro de areia de modo que as portas e a válvula de controle
estejam acessíveis para a operação, manutenção e adaptação para o inverno.
3. O padrão de TESTE EN60335-2-41 exige que o filtro de areia seja fixado verticalmente no chão,
ou em um pedestal feito de madeira ou concreto, antes do uso, para evitar uma queda acidental
do filtro de areia. Totalmente montado o filtro de areia tem mais de 18kg. Os orifícios de
montagem devem ser de 8mm de diâmetros e com espaços de 86mm. Use dois parafusos e
porcas com um máximo de 8mm de diâmetro para apertar o filtro de areia no pedestal.
Bestway
86mm Φ8
1
4
78
56
23
c
D
c
c
c
c
c
#20
0.45-0.85 mm
MAX
MIN
MAX
MIN
COLOQUE A AREIA DE FILTRO PARA PISCINA/POLI ESFERAS FLOWCLEAR™.
NOTA: Use somente areia para filtros especiais para piscinas, sem calcário ou argila: #20 areia sílica 0.45- 0.85mm, aproximadamente um saco de
9kg será suficiente. Se não utilizar o tamanho recomendado de filtro de areia, o desempenho de filtragem será reduzido e o filtro de areia pode ficar
danificado, invalidando, portanto, a garantia.
IMPORTANTE: Sugerimos o uso da areia de sílica nº 20 com o filtro de areia da sua piscina. Foi especialmente projetado para reter partículas na
faixa de 20 a 100 mícrons.
Alguns pequenos detritos podem passar para a areia e retornar à piscina. Isso é normal, especialmente se os detritos forem finos ou siltosos.
Para limitar isso, é melhor seguir as instruções de manutenção e lavar e enxaguar quando necessário.
Também sugerimos entrar em contato com o revendedor da piscina para obter o produto químico feito especificamente para limpar a areia. A
manutenção correta da areia otimiza a eficiência da limpeza e evita o acúmulo de óleos ou incrustações.
Quando você aspira o fundo da piscina que possui uma grande quantidade de detritos, sugerimos que você lave a areia ao terminar a limpeza de
metade da piscina.
Lembre-se de lavar e enxaguar a areia toda vez que aspirar pelo fundo da piscina.
NOTA: Para evitar danificar a escumagem ao adicionar a areia, coloque um pouco de água dentro do tanque inferior de modo a cobrir a escumagem
no cubo do coletor.
NOTA: A areia/poli esferas Flowclear™ não estão incluídas.
NOTA: Utilize 28 g de poli esferas Flowclear™ para substituir 1 kg de areia.
20
c
D
D
A
C
Bestway
VISÃO GERAL DA VÁLVULA DE CONTROLE
ATENÇÃO: Para evitar danos ao equipamento e possivelmente
riscos, desligue sempre a bomba do filtro de areia antes de mudar
a função da válvula de controle. Mudar as posições das válvulas
enquanto a bomba estiver funcionamento pode danificar a válvula
de controle, o que pode causar danos
pessoais ou danos à propriedade.
Como usar a válvula de controle
Pressione o manípulo da válvula de controle e gire na função
desejada.
FUNÇÕES DA VÁLVULA DE CONTROLE
A válvula de controle é usada para selecionar 6 funções
diferentes do filtro: Filtragem, Fechamento, Retorno,
Enxágüe, Drenagem e Circulação.
Pos. do botão
0
6
8
10
12
24
P4
P6
P8
Tempo de operação (H)
/
6
8
10
12
24
4
6
8
Tempo de pausa (H)
/
18
16
14
12
0
4
6
8
Período de ciclo (H)
/
24
24
24
24
24
8
12
16
TEMPORIZADOR
1. Ligue à fonte de alimentação, rode o botão para a posição desejada. O filtro de areia começará a funcionar imediatamente.
2. Rode o botão para a posição "0". O filtro de areia deixará de funcionar imediatamente.`
3. Depois de ligar, pode ajustar o tempo de operação, tempo de pausa e tempo de ciclo rodando o botão para a posição desejada.
Ver a tabela em baixo para mais pormenores.
4. Quando o botão do temporizador é movido para a nova posição, o ciclo anterior do filtro cancela automaticamente de forma a
começar um novo ciclo.
5. De cada vez que o filtro é ligado ou reiniciado, começa um ciclo novo com base na posição do botão do temporizador.
NOTA:
Se o botão estiver ajustado para a posição das 24 horas (24), o filtro de areia irá funcionar continuamente sem qualquer período de pausa.
FUNCIONAMENTO
Antes de ligar, por favor leia atentamente o manual.
PARE
AB
26-1
26-2
PARA PISCINAS COM VÁLVULA DE 32MM (1.25POL.)
Produkt Specifikationer
| Mærke: | Bestway |
| Kategori: | Over jorden swimmingpool |
| Model: | Power Steel 561EJ |
Har du brug for hjælp?
Hvis du har brug for hjælp til Bestway Power Steel 561EJ stil et spørgsmål nedenfor, og andre brugere vil svare dig
Over jorden swimmingpool Bestway Manualer
30 December 2025
30 December 2025
25 December 2024
25 December 2024
25 December 2024
25 December 2024
29 September 2024
29 September 2024
20 September 2024
20 September 2024
Over jorden swimmingpool Manualer
- Over jorden swimmingpool Crivit
- Over jorden swimmingpool Intex
- Over jorden swimmingpool Exit
- Over jorden swimmingpool Gre
- Over jorden swimmingpool JILONG
- Over jorden swimmingpool Summer Waves
- Over jorden swimmingpool Exit Toys
Nyeste Over jorden swimmingpool Manualer
30 December 2025
27 December 2024
19 September 2024
14 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024