Black And Decker BDTM250 Manual

Black And Decker Ikke kategoriseret BDTM250

Læs nedenfor 📖 manual på dansk for Black And Decker BDTM250 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 22 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/4
WARNING: Read and understand all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Safety Instructions
DANGER: Laser Radiation, avoid direct eye exposure, serious eye injury can result.
• Do not use optical tools such as a telescope or transit to view the laser beam.
• Position the laser so unintentional eye contact will be avoided.
• Do not operate the laser tape measure around children or allow children to operate the laser
tape measure.
• Do not disassemble. Modifying the product in any way can increase the risk of laser
radiation.
WARNING: Use of controls or adjustments or performance of procedures other than those
specified in this manual may result in hazardous laser radiation exposure.
• Do not operate in explosive atmospheres, such as in the presence of flammable liquids,
gases, or dust.
• Use only with the specifically designated LR44 battery. Use of any other battery may create
a risk of fire.
• Store idle product out of reach of children and other untrained persons. Lasers are
dangerous in the hands of untrained users.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one laser, may create a risk of injury when used on
another laser.
• Repairs and servicing MUST be performed by a qualified repair facility. Repairs performed
by unqualified personnel could result in serious injury.
• Do not remove or deface warning labels. Removing labels increases the risk of exposure to
radiation.
• For indoor use only.
• This product is intended for use in a temperature range of 41°F(5°C) - 104°F(40°C).
CAUTION: Use caution when drilling, nailing or cutting into walls, floors and ceilings which
may contain electrical wiring or pipes. Always turn off the power when working near
electrical wires.
The label on your tool may include the following symbols.
V ................................volts mW......................milliwatts
nm..............................wavelength IIa ........................Class IIa Laser
in nanometers
Inserting the Batteries:
1. Check to make sure the laser on/off switch ( ) is inA
the OFF (0) position.
2. Insert a coin or slotted screwdriver into the slot in
the battery compartment door (E). Stack the three
LR44 batteries (included) into the battery compartment
with the positive (+) flat side facing up. See figure 1.
3. Close the battery door making sure that it “clicks”
closed.
WARNING: The batteries used in this device may
present a risk of fire or chemical burn if mistreated. To
reduce this risk:
• Do not recharge, disassemble, incinerate or
expose to high temperatures.• Replace batteries
with model LR44 only. Use of another battery may
present a risk of fire or explosion. • Dispose of used battery promptly per local codes. •
Keep away from children. • Do not disassemble or short terminals. • Do not mix old and
new batteries. Replace all of them at the same time with new batteries of the same
brand and type.
• Remove batteries if the device will not be used for several months.
Transporting batteries can possibly cause fires if the battery terminals inadvertently come in
contact with conductive materials such as keys, coins, hand tools and the like. The US
Department of Transportation Hazardous Material Regulations (HMR) actually prohibit
transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon
luggage) UNLESS they are properly protected from short circuits. So when transporting
individual batteries, make sure that the battery terminals are protected and well insulated
from materials that could contact them and cause a short circuit.
Operation
WARNING: Always use proper eye protection.
To turn the laser on, push the laser on/off switch
(A) forward to the position. To turn the laser off,(I)
push back on the switch to the (0) position. The
laser can be positioned on either side of the tape
measure. To rotate 180 degrees, turn the laser as
shown in figure 3.
EXTENDING AND RETRACTING THE TAPE
To extend the tape (G), pull it out to the desired
length.
To retract the tape, push in on the tape release
button ( ). The speed that the tape is retractedB
can be controlled by releasing the button and
then pressing it in again.
CAUTION: To prevent injury avoid “full
speed” blade return.
USING THE TAPE AND LASER TOGETHER
1.) Extend the measuring tape and position the
unit on the edge of the item that you will be
measuring.
2.) Extend the the “leg” as shown in figure 4 and
hold it firmly against the edge of the work
surface.
.
3.) Turn the laser on ( ). With the laser linefigure 5
projected across the measuring tape, adjust the
tape to the distance that you require.
4.) Mark the surface along the laser line with a
pencil.
5.) When making a measurement to the rear of
the tape housing, add 4" (102mm) as shown in
Figure 6.
CALIBRATION
The BDTM250 Laser Tape Measure is calibrated
at the manufacturing plant. However, if the unit is
dropped or receives a hard blow it may need to
be recalibrated. Should you find that the laser line
needs to be adjusted, follow the steps below:
1.) Lay a carpenter's square on your work
surface with the short side of the square along
the edge of your work surface.
2.) Extend the tape out about 12 inches. Extend
the 'leg' and hold it firmly against the short side of
the square.
3.) Turn the laser on making sure the laser line
will be projected in the same direction as the
square that is on your workpiece.
4.) Turn the calibration screw shown in figure 7.
( Clockwise adjusts the line toward the rear of the
unit. Counter-clockwise adjusts the line toward
the front of the unit.) Align the laser line with the
straight edge of the square.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
CAT. NO. BDTM250 FORM NO.490808-00 Copyright2006 Black & Decker (FEB. ‘06) Printed in China
1
A
B
C
D
E
Features
A.) Laser On/Off Switch
B.) Tape Release Button
C.) Laser
D.) Laser Calibration Screw (on laser)
E.) Battery Compartment
F.) Belt Clip
G.) 25 Foot Tape
H.) Extendable Leg
F
G
H
2
3
7
Calibration Screw
For your convenience and safety, the following laser warning label is on your laser:
4
5
6
T
THANK
HANK YOU
YOU FOR
FOR CHOOSING
CHOOSING B
BLACK
LACK &
&D
DECKER
ECKER!
!
G
GO
OT
TO
OWWW
WWW.B
.BLACKAND
LACKANDD
DECKER
ECKER.
.COM
COM/N
/NEW
EWO
OWNER
WNER
T
TO
OREGISTER
REGISTER YOUR
YOUR NEW
NEW PRODUCT
PRODUCT.
.
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A
BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.
YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
INSTRUCTION MANUAL
L
L
L
L
L
L
L
L
L
La
a
a
a
a
a
a
a
a
as
s
s
s
s
s
s
s
s
se
e
e
e
e
e
e
e
e
er
r
r
r
r
r
r
r
r
r
T
T
T
T
T
T
T
T
T
Ta
a
a
a
a
a
a
a
a
ap
p
p
p
p
p
p
p
p
pe
e
e
e
e
e
e
e
e
e
M
M
M
M
M
M
M
M
M
Me
e
e
e
e
e
e
e
e
ea
a
a
a
a
a
a
a
a
as
s
s
s
s
s
s
s
s
su
u
u
u
u
u
u
u
u
ur
r
r
r
r
r
r
r
r
re
e
e
e
e
e
e
e
e
e
-
-
-
-
-
-
-
-
-
-
C
C
C
C
C
C
C
C
C
Ca
a
a
a
a
a
a
a
a
at
t
t
t
t
t
t
t
t
t.
.
.
.
.
.
.
.
.
.N
N
N
N
N
N
N
N
N
No
o
o
o
o
o
o
o
o
o.
.
.
.
.
.
.
.
.
.B
B
B
B
B
B
B
B
B
BD
D
D
D
D
D
D
D
D
DT
T
T
T
T
T
T
T
T
TM
M
M
M
M
M
M
M
M
M2
2
2
2
2
2
2
2
2
25
5
5
5
5
5
5
5
5
50
0
0
0
0
0
0
0
0
0

Produkt Specifikationer

Mærke: Black And Decker
Kategori: Ikke kategoriseret
Model: BDTM250

Har du brug for hjælp?

Hvis du har brug for hjælp til Black And Decker BDTM250 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Black And Decker Manualer

Black And Decker

Black And Decker WM600SC Manual

14 Oktober 2024
Black And Decker

Black And Decker BDS300 Manual

30 September 2024
Black And Decker

Black And Decker HHVJ315JDP07 Manual

29 September 2024
Black And Decker

Black And Decker CWV9610 Manual

23 September 2024
Black And Decker

Black And Decker RC860 Manual

22 September 2024
Black And Decker

Black And Decker WM600SB Manual

18 September 2024
Black And Decker

Black And Decker Dustbuster VP7240 Manual

16 September 2024
Black And Decker

Black And Decker SC100 Manual

12 September 2024
Black And Decker

Black And Decker AV1600B Manual

8 September 2024
Black And Decker

Black And Decker RC3303 Manual

7 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SKROSS

SKROSS World Adapter Pro+ Manual

26 November 2024
SKROSS

SKROSS PRO – World & USB Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024