Black And Decker CD1402 Manual
Black And Decker
Boremaskine
CD1402
Læs nedenfor 📖 manual på dansk for Black And Decker CD1402 (6 sider) i kategorien Boremaskine. Denne guide var nyttig for 36 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/6
1
2
3
4
1
2
3
GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all
instructions listed below, may result in electric shock, fire and/or serious personal injury
SAVE THESE INSTRUCTIONS
WORK AREA
• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.
• Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
• Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from
heat, oil, sharp edges or moving parts. Replace damaged cords immediately.
Damaged cords may create a fire.
• A battery operated tool with integral batteries or a separate battery pack must be
recharged only with the specified charger for the battery. A charger that may be suitable
for one type of battery may create a risk of fire when used with another battery.
• Use battery operated tool only with specifically designated battery pack. Use of any
other batteries may create a risk of fire.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in serious
personal injury,
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing , and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts. Air vents cover moving parts and should be avoided.
• Avoid accidental starting. Be sure switch is in the locked or off position before
inserting battery pack. Carrying tools with your finger on the switch or inserting the battery
pack into a tool with the switch on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is
left attached to a rotating part of the tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enable better control of the tool in unexpected situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of
control.
• Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the
switch is dangerous and must be repaired.
• Disconnect battery pack from tool or place the switch in the locked or off position
before making any adjustments, changing accessories, or storing the tool. Such
preventative safety measures reduce the risk of starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
• When battery pack is not in use, keep it away from other metal objects like: paper
clips, coins, keys, nails, screws or other small metal objects that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause sparks, burns, or a fire.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edge are less likely to bind and are easier to control.
• Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tool’s operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may create a risk of injury when used on
another tool.
SERVICE
• Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel may result in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow instructions in
the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of shock or injury.
SPECIFIC SAFETY RULES
• Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will
also make exposed metal parts of the tool "live" and shock the operator.
• When working on a ladder or on scaffolding be sure to lay the tool down on its side
when not in use. Some tools with large battery packs will stand upright but may be easily
knocked over.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
FIRST AID MEASURES FOR GEL COMPONENTS (CD120G, CD140G, CD180G)
If gel within the comfort grip becomes exposed and results in skin contact wash with soap
and water; for eye contact, flush with flowing water. If swallowed, seek medical attention.
Material Safety Data Sheet (MSDS) available from 1-800-544-6986.
The label on your tool may include the following symbols.
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min ........................minutes ......................alternating current
......................direct current n o ........................no load speed
..........................Class II Construction ........................earthing terminal
........................safety alert symbol .../min ..................revolutions or
reciprocations per minute
BATTERY CAP INFORMATION
Battery storage and carrying caps are provided for use whenever the battery is out of the
tool or charger. Remove cap before placing battery in charger or tool.
WARNING: Do not store or carry battery so that metal objects can
contact exposed battery terminals. For example, do not place battery
in aprons, pockets, tool boxes, product kit boxes, drawers, etc. with
loose nails, screws, keys, etc. without battery cap. Transporting
batteries can possibly cause fires if the battery terminals inadvertently
come in contact with conductive materials such as keys, coins, hand
tools and the like. The US Department of Transportation Hazardous
Material Regulations (HMR) actually prohibit transporting
batteries in commerce or on airplanes (i.e. packed in suitcases and
carryon luggage) UNLESS they are properly protected from short
circuits. So when transporting individual batteries, make sure that the
battery terminals are protected and well insulated from materials that
could contact them and cause a short circuit.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. LÉASE ESTEADVERTENCIA:
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
Cat. Nos. CD9602, CD1202, CD1402, CD1802, CD120G, CD140G, CD180G Form No. 5102936-35
Copyright© 2005 Black & Decker (MAY ‘05) Printed in China
INSTRUCTION MANUAL
Catalog Nos.
CD9602, CD1202, CD1402, CD1802,
CD120G, CD140G, CD180G
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
IF YOU SHOULD HAVE A QUESTION OR EXPERIENCE A
PROBLEM WITH YOUR BLACK & DECKER PRODUCT,
CALL 1-800-544-6986
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., AND
DATE CODE (e.g. 20000130M). IN MOST CASES, A REPRESENTATIVE CANBLACK & DECKER
RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGESTION OR COMMENT, GIVE
US A CALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.
1
2
3
4
1
2
3
4
1 2
9
9
9
9
99
9
9
9
9
99.
.
.
.
..
.
.
.
.
.. 6
6
6
6
66
6
6
6
6
66 ,
,
,
,
,,
,
,
,
,
,,
1
1
1
1
11
1
1
1
1
11 2
2
2
2
22
2
2
2
2
22,
,
,
,
,,
,
,
,
,
,,
1
1
1
1
11
1
1
1
1
11 4
4
4
4
44
4
4
4
4
44.
.
.
.
..
.
.
.
.
.. 4
4
4
4
44
4
4
4
4
44
&
&
&
&
&&
&
&
&
&
&&
1
1
1
1
11
1
1
1
1
118
8
8
8
88
8
8
8
8
88
V
V
V
V
VV
V
V
V
V
VVo
o
o
o
oo
o
o
o
o
ool
l
l
l
ll
l
l
l
l
ll t
t
t
t
tt
t
t
t
t
tt
C
C
C
C
CC
C
C
C
C
CC o
o
o
o
oo
o
o
o
o
oor
r
r
r
rr
r
r
r
r
rrd
d
d
d
dd
d
d
d
d
dd l
l
l
l
ll
l
l
l
l
lle
e
e
e
ee
e
e
e
e
ee s
s
s
s
ss
s
s
s
s
sss
s
s
s
ss
s
s
s
s
ss
D
D
D
D
DD
D
D
D
D
DD r
r
r
r
rr
r
r
r
r
rri
i
i
i
ii
i
i
i
i
ii l
l
l
l
ll
l
l
l
l
lll
l
l
l
ll
l
l
l
l
ll s
s
s
s
ss
s
s
s
s
ss
1
2
3
4
4
Torque Adjust Collar
collier de réglage du couple
collarÍn de ajuste de par (torque)
Depress for forward (other side)
Enfoncer pour la marche avant
Oprima para reversa
Depress for reverse (this side)
Enfoncer pour la marche arrière
Oprima para marcha hacia adelante
Trigger Switch
Interrupteur à détente
Gatillo interruptor
6
3
1
2
3
4
K
K
K
K
KK
K
K
K
K
KK E
E
E
E
EE
E
E
E
E
EEY
Y
Y
Y
YY
Y
Y
Y
Y
YY I
I
I
I
II
I
I
I
I
IIN
N
N
N
NN
N
N
N
N
NNF
F
F
F
FF
F
F
F
F
FFO
O
O
O
OO
O
O
O
O
OO R
R
R
R
RR
R
R
R
R
RRM
M
M
M
MM
M
M
M
M
MMA
A
A
A
AA
A
A
A
A
AAT
T
T
T
TT
T
T
T
T
TTI
I
I
I
II
I
I
I
I
IIO
O
O
O
OO
O
O
O
O
OON
N
N
N
NN
N
N
N
N
NN Y
Y
Y
Y
YY
Y
Y
Y
Y
YY O
O
O
O
OO
O
O
O
O
OOU
U
U
U
UU
U
U
U
U
UU S
S
S
S
SS
S
S
S
S
SSH
H
H
H
HH
H
H
H
H
HH O
O
O
O
OO
O
O
O
O
OOU
U
U
U
UU
U
U
U
U
UUL
L
L
L
LL
L
L
L
L
LLD
D
D
D
DD
D
D
D
D
DD K
K
K
K
KK
K
K
K
K
KKN
N
N
N
NN
N
N
N
N
NNO
O
O
O
OO
O
O
O
O
OO W
W
W
W
WW
W
W
W
W
WW:
:
:
:
::
:
:
:
:
::
•Charge battery for 9 hours before first use. For more information see
“CHARGING THE POWER PACK”.
5
Battery Cap
Produkt Specifikationer
| Mærke: | Black And Decker |
| Kategori: | Boremaskine |
| Model: | CD1402 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Black And Decker CD1402 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Boremaskine Black And Decker Manualer
28 Juni 2024
30 April 2024
27 April 2024
26 April 2024
18 April 2024
12 April 2024
9 April 2024
2 April 2024
30 Marts 2024
30 Marts 2024
Boremaskine Manualer
- Boremaskine Scheppach
- Boremaskine Ikea
- Boremaskine Bosch
- Boremaskine Ozito
- Boremaskine Guede
- Boremaskine Panasonic
- Boremaskine Metabo
- Boremaskine DeWalt
- Boremaskine RYOBI
- Boremaskine Silverline
- Boremaskine Skil
- Boremaskine AEG
- Boremaskine Carat
- Boremaskine Zipper
- Boremaskine Stihl
- Boremaskine Makita
- Boremaskine Worx
- Boremaskine Güde
- Boremaskine Vonroc
- Boremaskine Milwaukee
- Boremaskine Clas Ohlson
- Boremaskine Parkside
- Boremaskine Einhell
- Boremaskine Proxxon
- Boremaskine Stanley
- Boremaskine Hikoki
- Boremaskine Hilti
- Boremaskine Hitachi
- Boremaskine Alpha Tools
- Boremaskine Bavaria
- Boremaskine Festool
- Boremaskine Dremel
- Boremaskine Fein
- Boremaskine Topcraft
- Boremaskine Powerfix
- Boremaskine Festo
- Boremaskine Craftsman
- Boremaskine Powerplus
- Boremaskine Malmbergs
- Boremaskine Westfalia
- Boremaskine Genesis
- Boremaskine Fieldmann
- Boremaskine Velleman
- Boremaskine Kawasaki
- Boremaskine Porter-Cable
- Boremaskine Baumr-AG
- Boremaskine Ridgid
- Boremaskine Sun Joe
- Boremaskine Cotech
- Boremaskine Hazet
- Boremaskine SKIL Masters
- Boremaskine Truper
- Boremaskine Meec Tools
- Boremaskine Brüder Mannesmann
- Boremaskine Steren
- Boremaskine Graphite
- Boremaskine Cocraft
- Boremaskine Maestro
- Boremaskine Wolfcraft
- Boremaskine Mac Tools
- Boremaskine Workzone
- Boremaskine Tryton
- Boremaskine Stalco
- Boremaskine Black Decker
- Boremaskine MSW
- Boremaskine Prowork
Nyeste Boremaskine Manualer
8 December 2024
8 December 2024
8 December 2024
8 December 2024
8 December 2024
8 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024