Black And Decker PD600 Manual
Black And Decker
Skruemaskine
PD600
Læs nedenfor 📖 manual på dansk for Black And Decker PD600 (6 sider) i kategorien Skruemaskine. Denne guide var nyttig for 32 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/6
GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in electric shock, fire and/or serious
personal injury. SAVE THESE INSTRUCTIONS
Work Area
•Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.
• Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
• A battery operated tool with integral batteries or a separate battery pack must be
recharged only with the specified charger for the battery. A charger that may be suitable
for one type of battery may create a risk of fire when used with another battery.
• Use battery operated tool only with specifically designated battery pack. Use of any
other batteries may create a risk of fire.
Personal Safety
• Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in serious
personal injury,
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts.
• Avoid accidental starting. Be sure switch is in the locked or off position before
inserting battery pack. Carrying tools with your finger on the switch or inserting the battery
pack into a tool with the switch on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that
is left attached to a rotating part of the tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enable better control of the tool in unexpected situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
Tool Use and Care
• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of
control.
• Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with
the switch is dangerous and must be repaired.
• Disconnect battery pack from tool or place the switch in the locked or off position
before making any adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce the risk of starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
• When battery pack is not in use, keep it away from other metal objects like: paper
clips, coins, keys, nails, screws or other small metal objects that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause sparks, burns, or a fire.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edge are less likely to bind and are easier to control.
• Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tool’s operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may create a risk of injury when used on
another tool.
Service
• Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel may result in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow instructions in
the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of shock or injury.
Specific Safety Rules
•Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed
metal parts of the tool "live" and shock the operator.
First Aid Measures for Gel Components (PD600G Only)
If gel within the comfort grip becomes exposed and results in skin contact wash with soap and
water; for eye contact, flush with flowing water. If swallowed, seek medical attention.
Material Safety Data Sheet (MSDS) available from 1-800-544-6986.
The label on your tool may include the following symbols.
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min ........................minutes ......................alternating current
......................direct current no ........................no load speed
..........................Class II Construction ........................earthing terminal
........................safety alert symbol .../min ..................revolutions or
reciprocations
per minute
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
Safety Warnings and Instructions: Charging
1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary warnings on battery
charger and product using battery. CAUTION: To reduce the risk of injury, use charger
only with this product. Batteries in other products may burst causing personal injury or
damage.
3. Do not expose charger to rain or snow.
4. Use of an attachment not recommended or sold by Black & Decker may result in a risk
of fire, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting charger.
6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
7. An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed
extension cords should be used, and we recommend that they be listed by
Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must
be suitable for outdoor use. Any cord marked for outdoor use can also be used for
indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable
for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety, and to prevent loss of power and overheating. The smaller the gauge number of
the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than
18 gauge. When using more than one extension to make up the total length, be sure
each extension contains at least the minimum wire size.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTESADVERTENCIA:
DE USAR EL PRODUCTO.
INSTRUCTION MANUAL
C
C
C
C
C
C
C
C
C
CO
O
O
O
O
O
O
O
O
OR
R
R
R
R
R
R
R
R
RD
D
D
D
D
D
D
D
D
DL
L
L
L
L
L
L
L
L
LE
E
E
E
E
E
E
E
E
ES
S
S
S
S
S
S
S
S
SS
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
SC
C
C
C
C
C
C
C
C
CR
R
R
R
R
R
R
R
R
RE
E
E
E
E
E
E
E
E
EW
W
W
W
W
W
W
W
W
WD
D
D
D
D
D
D
D
D
DR
R
R
R
R
R
R
R
R
RI
I
I
I
I
I
I
I
I
IV
V
V
V
V
V
V
V
V
VE
E
E
E
E
E
E
E
E
ER
R
R
R
R
R
R
R
R
R
Cat No. PD600, PD600G Form No. 5145342-00 (NOV-04) Copyright © 2004 Black & Decker Printed in China
1
2
3
4
FEATURES
- Quick Release Collar
- Torque Control Collar
- LED Light
- Two Speed Switch
- Accessory Holder
- Pivot Button
- Charging Port
- Forward / Reverse Switch
A
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1 - 8 0 0 - 5 4 4 - 6 9 8 6
IF YOU SHOULD HAVE A QUESTION OR
EXPERIENCE A PROBLEM WITH YOUR
BLACK & DECKER PRODUCT,
CALL 1-800-544-6986
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No.,
TYPE No., AND DATE CODE (e.g. 0130M). IN MOST CASES, ABLACK & DECKER REPRE-
SENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGES-
TION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
C
B
D
E
F
GH
A
B
C
D
E
F
G
H
5
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gage
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
Catalog No. PD600, PD600G
Produkt Specifikationer
| Mærke: | Black And Decker |
| Kategori: | Skruemaskine |
| Model: | PD600 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Black And Decker PD600 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Skruemaskine Black And Decker Manualer
6 September 2024
4 September 2024
6 August 2024
6 August 2024
3 August 2024
2 August 2024
1 August 2024
30 Juli 2024
27 Juli 2024
25 Juli 2024
Skruemaskine Manualer
- Skruemaskine Bosch
- Skruemaskine Ozito
- Skruemaskine EasyMaxx
- Skruemaskine Panasonic
- Skruemaskine Metabo
- Skruemaskine DeWalt
- Skruemaskine RYOBI
- Skruemaskine Silverline
- Skruemaskine Skil
- Skruemaskine Mafell
- Skruemaskine AEG
- Skruemaskine Senco
- Skruemaskine Emos
- Skruemaskine Omega
- Skruemaskine Makita
- Skruemaskine Worx
- Skruemaskine Güde
- Skruemaskine Biltema
- Skruemaskine Vonroc
- Skruemaskine Milwaukee
- Skruemaskine Laserliner
- Skruemaskine Parkside
- Skruemaskine FERM
- Skruemaskine Power Craft
- Skruemaskine Trotec
- Skruemaskine Einhell
- Skruemaskine Stanley
- Skruemaskine Hikoki
- Skruemaskine Hilti
- Skruemaskine Hitachi
- Skruemaskine Alpha Tools
- Skruemaskine Bavaria
- Skruemaskine Facom
- Skruemaskine Kress
- Skruemaskine Festool
- Skruemaskine Dremel
- Skruemaskine Fein
- Skruemaskine Powerfix
- Skruemaskine Craftsman
- Skruemaskine Powerplus
- Skruemaskine Westfalia
- Skruemaskine Genesis
- Skruemaskine Chicago Pneumatic
- Skruemaskine Basetech
- Skruemaskine Carrera
- Skruemaskine Ingersoll Rand
- Skruemaskine Fieldmann
- Skruemaskine Kawasaki
- Skruemaskine Porter-Cable
- Skruemaskine Cotech
- Skruemaskine Chamberlain
- Skruemaskine Hazet
- Skruemaskine Park Tool
- Skruemaskine Truper
- Skruemaskine Beta
- Skruemaskine Meec Tools
- Skruemaskine Brüder Mannesmann
- Skruemaskine Bavaria By Einhell
- Skruemaskine StarTech.com
- Skruemaskine Wiha
- Skruemaskine Toolcraft
- Skruemaskine Steren
- Skruemaskine Yato
- Skruemaskine Cocraft
- Skruemaskine Mac Tools
- Skruemaskine Toolland
- Skruemaskine Tacklife
- Skruemaskine Fischer
- Skruemaskine Meister Craft
- Skruemaskine Batavia
- Skruemaskine Wera
- Skruemaskine Goon
- Skruemaskine Dedra
- Skruemaskine Sthor
- Skruemaskine Pansam
- Skruemaskine Gedore
- Skruemaskine SW-Stahl
- Skruemaskine Cleco
- Skruemaskine Weidmüller
- Skruemaskine Einhell Bavaria
- Skruemaskine Rodcraft
- Skruemaskine Prowork
- Skruemaskine TAURUS Titanium
- Skruemaskine Total
Nyeste Skruemaskine Manualer
16 December 2024
10 December 2024
4 December 2024
4 December 2024
4 December 2024
23 November 2024
23 November 2024
23 November 2024
23 November 2024
23 November 2024