Blaupunkt IRC-S2 Manual

Blaupunkt Overvågningskamera IRC-S2

Læs nedenfor 📖 manual på dansk for Blaupunkt IRC-S2 (2 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 61 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Wireless PIR Camera (IRC-S2)

1. Blue LED /Learn Button

2. IR Sensor

3. LED Flash

T LED Flash delivers sufficient light for image capture in low he

lighting condition .

4. PIR Camera Lens

5. Battery Insula tor

Pull out the insulator to activate battery.

6. Bottom Screw (Tamper Switch)

The Tamper switch protects the PIR Camera from unauthorized

cover opening and is depressed by bottom screw. When the

screw is loosened, the tamper switch will be activate.

PPaacckkaaggee CCoonntteenntt

1 x PIR Camera

4 x wall plugs and screws

2 1.5V AA alkaline batteries (Pre-inserted) x

The PIR Camera can only be learnt into Control Panel within 3

minutes after powering on. If it has been powered on for more

than 3 minutes, remove and reinsert batteries to repower on the

PIR Camera.

1. Put the Control Panel into learning mode l.

2. Press and hold the learn button PIR Camera for 10 on

seconds until both LED Flash and Blue LED flash once, then

release the button to transmi learn code. t a

3. Wait for a short time for PIR Camera to connect to panel. If the

camera is successfully learnt in, the Blue LED will flash twice

to indicate. The panel will also display PIR Camera info. Refer

to panel manual to complete learning.

4. If the PIR Camera and Control do not respond after a short

time (about 20~30 seconds), restart from step 2 to press and

hold the button again.

After learning has been completed, Do press and hold the NOT

learn button for 10 seconds again within 3 minutes after power on,

otherwise the PIR Camera will disconnect from panel and must

be relearnt again.

 T PIR camera designed to be mounted on either a flat surface he

or in a corner with fixing screws and plugs provided.

 The base has knockouts where the plastic is thinner and can be

broken through for mounting. 2 in the center for surface

mounting and 4 on the sides for corner mounting.

1. Remove the cover.

2. For surface mounting, break through the knockouts at t 2 he

center of base.

For corner mounting, break through the 4 knocks on the

corner of PIR camera

3. e the holes as template Us to drill holes in the wall.

4. Insert the wall plugs if fixing it into plaster or brick.

5. Screw the base into the wall plugs.

6. Screw the cover back onto its base.

MMoottiioonn DDeetteeccttiioonn

The PIR Camera is designed to detect movement in protected

area. Upon movement detection, the PIR reports to the Control

Panel for an alarm activation captures 3 images at the same and

time. The images are transferred to the Control Panel to send to

programmed destinations for user to view.

When the Control Panel enters arm mode, or PIR Camera is put

into Test Mode, the PIR Camera will warm up for 30 seconds. Do

not trigger the PIR Camera during the 30 seconds warm up

period. If the PIR Camera is under low battery or tamper opened

condition, the Blue LED will light up during the warm up period.

BBaatttteerryy

The PIR Camera uses two 1.5V AA Alkaline batteries as its power

source. Remove the battery insulator to activate battery. It also

features low battery detection function to notify the Control Panel

when battery voltage is low.

When the PIR camera is low battery, follow the procedure on

below to change the batteries.

1. Open the PIR camera back cover.

2. Remove the old batteries.

3. Press the tamper switch several times to fully discharge.

4. Insert the new batteries and replace the PIR Camera back

cover.

OOppeerraattiioonn

Surface Fixing

Knockouts x 2

Corner Fixing

Knockouts x 4

Produkt Specifikationer

Mærke:	Blaupunkt
Kategori:	Overvågningskamera
Model:	IRC-S2
Produktfarve:	Hvid
Batteriteknologi:	Lithium
Dimensioner (BxDxH):	50 x 43.3 x 99 mm
Forbindelsesteknologi:	Trådløs
Batterilevetid:	4 År
Batteritype:	AA
Antal understøttede batterier:	2
Indgangsspænding:	1.5 V
Sensortype:	Passiv infrarød (PIR) sensor
Maks. rækkevidde:	10 m
Alarmfunktion:	Ja
Registreringsvinkel:	120 °