Boss ATVB95LED Manual

Boss Ikke kategoriseret ATVB95LED

Læs nedenfor 📖 manual på dansk for Boss ATVB95LED (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/1
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of this device.
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by
user. This equipment complies with FCC/ IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE). But it is desirable that it should
be installed and operated keeping the radiator at least 20 cm or more away from
person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration
or modications carried out without appropriate authoriation may invalidate the
user’s right to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o󰀨 and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
 Relocate or reorient the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit di󰀨erent from that to which the
receiver is connected.
 Consult the dealer or an experienced radio/T technician for help.
THIS PACKAGE CONTAINS
1 - ATB5E All-Terrain Speaker System
1 - Bluetooth Multi-Function Controller
1 - Handlebar Mounting Kit
1 - Quick Connect Power Extension Adaptor
4 - Hi-strength Nylon Mounting Straps
1 - User Manual Quick Start Guide / Poster
1 - Warranty Card
USER MANUAL
QUICK START GUIDE
Thank you for purchasing this
ATVB95LED All-Terrain Sound System
Please read through these instructions carefully so you will know
how to operate your model properly.
$ Y À fter you ha e nished reading the instructions keep this document
in a safe place for future reference.
INFORMATION TO THE USER
INFORMATION TO THE USER
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks is under license.
Other trademarks and trade names are those of their respective owners.
CAUTION!!
ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
GETTING TO KNOW YOUR
ATVB95LED MULTIFUNCTION CONTROLLER (MFC)
BEFORE YOU START
IMPORTANT SAFETY PRECAUTIONS
o not operate mobile equipment while driving a motoried vehicle  safe driving and
safety consideration of others should always be your highest priority.
In the event you should notice smoke, strange noises or odor from this product, or any
other abnormal signs, immediately turn o󰀨 the power and consult your dealer or the near-
est authoried BOSS AUDIO Service Center. Using this product in this condition may result
in permanent damage to the system.
Set your volume control at a low setting, then slowly increase the sound until you can
hear it comfortably without distortion, or ear discomfort.
:BE SURE TO OBSERVE THE FOLLOWING GUIDELINES
- o not turn up the volume so high that you can’t hear what’s around you.
- Use caution or temporarily discontinue use in potentially haardous situations.
INSTALLATION PRECAUTIONS
WARNING - Always consult a professional installer
o not attempt to install or service this product by yourself. Installation or servicing of this
product by persons without professional training and experience in electronic equipment
and motoried vehicle accessories may be dangerous and could expose you to the risk of
electric shock, injury or other haards
Refer any repairs to a qualied Service CenterBOSS AUDIO SYSTEMS
The ATVB95LED can be powered from a vehicles cigarette lighter / auxiliary power port,
or hard wired directly to the battery through an optional relay / accessory switch
When wiring directly to the vehicles battery, be sure to disconnect the batteries negative
terminal wire before starting any wiring procedures, it is suggested that an optional fuse
and fuse holder (not included) with minimum rating of be in line with the positive 20 Amps
battery terminal
The ground cable length should not exceed 18-inches (See wiring diagram)
The ATVB95LED has a weather resistant design, it should not be submerged under
water under any circumstances
Use only the installation parts provided with the ATVB95LED
Ensure the is not mounted behind metalMFC
o not install the next to the vehicles electronicsMFC
Never install this product in a heated location
GETTING STARTED
CAUTION!! Using other mounting methods may void this warranty
PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION
1) Power on the MFC by pressing and holding down the 2 for 3 seconds Power button
2) Press the PLAY/PAUSE 4button for 3 seconds, the 5 will quickly ash, BLUE LED
signalling that the pairing. MFC is now ready for Bluetooth
3) Now that the MFC is in pairing mode:
ANDROID users:
a. Go into the of your deviceSettings Menu
b. Enter the Bluetooth Menu
c. TURN ON Bluetooth and press SCAN
d. “BOSS AUDIO ATV” will now be displayed under AVAILABLE DEVICES
e. If prompted, enter passcode: “ ”0000
iOS users:
a. Go into the of your Settings Menu iOS device
b. Enter the Bluetooth Menu
c. TURN ON Bluetooth
d. “BOSS AUDIO ATV” will now be displayed
e. If prompted, enter passcode: “ ”0000
4) If BOSS AUDIO ATV is not seen, repeat the above steps and refresh the “Device List”
5) You will hear a tone when the connection is successful, you are now ready to stream
music from your favorite media player to the ATVB95LED
NOTE: You have 2 minutes before you must restart this procedure over again.
To avoid battery exhaustion, be sure to occasionally run the
vehicles engine while using this product.
Using this product without running the engine can drain the battery.
BLUETOOTH OPERATION BLUETOOTH OPERATION
RECONNECTION
1) Power on the and your last paired device Bluetooth.MFC
2) The unit will now automatically reconnect
3) If your device was previously paired with the MFC, but it wasn’t the last paired
device:
a. Ensure no other devices are currently paired
b. Enter the Bluetooth Menu on your device being paired
c. “BOSS AUDIO ATV” will display under AVAILABLE DEVICES
d. Choose the “BOSS AUDIO ATV” to reconnect
4) If the device is out of range from the ATVB95LED, it will disconnect automatically:
a. If your device does not reconnect automatically once it is back in range, press
BOSS AUDIO ATV in your devices Bluetooth settings
b. The MFC will now reconnect to the device
5) If you turn o󰀨 on your device, then you must manually press BLUETOOTH
“BOSS AUDIO ATV” from your list to reconnect to the BLUETOOTH MFC
NOTE: The MFC can remember up to 8 devices, to clear all previously paired devices,
press and hold 2 POWER button for 10 seconds
Tips:
STREAMING MUSIC
Make sure your device Bluetooth volume is set at 100% level
before stowing
AUX-INPUT
Make sure your device headphone volume is set at 100% level
before stowing.
Tips: Tips:
MULTI-FUNCTION CONTROLLER MOUNTING
LEFT or RIGHT
FOR ILLUSTRATION PURPOSES
YOUR VEHICLE MAY VARY
TOOLS NEEDED:
- Wrench or Pliers
- Allen Wrench
BEFORE INSTALLING THIS PRODUCT
When replacing the fuse, be sure to only use a fuse of the rating specied on
this product. To avoid short-circuiting, cover any disconnected leads with insulating
tape. It is especially important to insulate any unused wires, which if left uncovered
may cause a short circuit. When connecting other devices to this product, refer to
the manual for the product to be connected. The black cable is ground, make sure
to connect the ground wire rst. Ensure that the ground wire is properly connected
to metal parts of the vehicles body frame or direct to the battery if your vehicle
does not have a grounded chassis frame The ground wire of this units power amp
and a second powered system must be connected to the frame separately with
di󰀨erent screws. If the screw for the ground wire loosens or falls out, it could result
in re or malfunction.
To avoid potential shorts in the electrical
system, be sure to disconnect the () bat-
tery cable before installation. Use this unit
with a 12-olt battery and negative ground-
ing only. Failure to do so may result in a
re or malfunction.
SPEAKER MOUNTING SUGGESTIONS
QUICK START GUIDE
SPECIFICATIONS
WIRE DIAGRAM
15A
Fuse and fuse holder
(not included)
Chassis
ground
point
BATTERY
Mini-DIN
Connector
Fuse is located inside the power adaptor
Turn counter clockwise to open
Replace with 10A AGC Fuse type only
INSERT
Normally open switch
(not included)
INSERT
OPTIONAL DIRECT BATTERY WIRING CIRCUIT
RED
BLACK
Chassis
ground
point
QUICK RELEASE
POWER ADAPTOR
(INCLUDED)
POWER ADAPTOR
10A
Ground wire
Metal frame
Recommended 12 ~ 14ga Wire
(not included)
Align arrows
(Cable not included)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Route strap
through the hole
and to vehicle
frame
Route strap
around the speaker body to vehicle frame
Route strap
through the hole
and to vehicle
frame
CAUTION!!
Mounting straps should be double checked to be sure they are
pulled tight and secure before each use of the vehicle.
1
2
3
4
5
6
7
8
9
9
87
2
4
1
MFC - MULTIFUNCTION CONTROLLER
LED LIGHTBAR ON/OFF
POWER ON/OFF - Press and hold for 3 seconds
NEXT TRACK
PLAY/PAUSE
BLUETOOTH PAIRING INDICATOR - BLUE COLOR
PREVIOUS TRACK
VOL DOWN
VOL UP
3.5mm AUX-IN
CABLE NOT INCLUDED
1A USB
CHARGING
NOT FOR AUDIO PLAYBACK
MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION
1) Press the 4 PLAY/PAUSE once to start playing music or press the PLAY button from
your devices touch screen
2) To skip songs or advance, press the 3NEXT TRACK button
3) To select the previous song, press the 6PREVIOUS TRACK button
VOLUME CONTROL
4) To raise the volume press the 8 VOL UP button
5) To lower the volume press the 7 VOL DOWN button
MULTIFUNCTION CONTROLLER AUX-IN OPERATION
1) Power on the by pressing and holding down the ATVB95LED 2POWER button for
3 seconds
2) isconnect any paired device by turning o󰀨 in your devices Bluetooth Bluetooth
Settings Menu
3) Connect your 3.5mm to your devices AUX-IN cable located on the front of the MFC
headphone jack, the E will illuminate color when in modeRED AUX-IN
4) Route the wire back to the , secure your device in a safe positionMFC
VOLUME CONTROL
5) To raise the volume press the 8 VOL UP button
6) To lower the volume press the 7 VOL DOWN button
7) To MUTE the volume press the 4 PLAY/PAUSE button
ATVB95LED can play audio
from any device that has a
3.5mm headphone audio jack.
YOUR DEVICE 8
7
2
BLUETOOTH
 ersion: 3.0 w/ ER
A2P / ARCP
 Range: 33ft (10m) Class 2
SPEAKERS
 imensions: 8”
 Impedance: 4  4
 Cone Type: PP CARBON  RESIN COTH
 Tweeter Sie: 1” PEI SOFT OME
AMPLIFIER
 Maximum Output Power: 700 Watts
 Class: AB
 Input impedance: 10k
 Frequency Response: 45H-25kH
GENERAL
 Operational Power: 14.4C (10-16 allowable)
 MA Current raw: 13.7A
 USB Charging: 1A 5C /- 5%
 Replacement Fuse: 10A AGC TYPE
 Color: Black
 Unit Weight: 22.2lbs / 10Kg
 imensions cm WxHx: 83.00 x 23.50 x 34.00
 imensions Inches WxHx: 32.68 x .25 x 13.38
 Storage Temperature: 5 oF to 113oF / -15oC to 45 o
C
 Operation Temperature: 14 oF to 140oF / -10oC to 60oC
0616
5
6
4
2
4
5
8
76
2
3
4
LIFT TO OPEN
ALWAYS CLOSE WHEN NOT IN USE
NEER USE AU-IN WHEN IN MU or WATER
3
ATVB95LED-UM-POSTER-STYLE-FINAL-v1.0.indd 2 5/4/2016 12:14:55 PM

Produkt Specifikationer

Mærke: Boss
Kategori: Ikke kategoriseret
Model: ATVB95LED

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss ATVB95LED stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Boss Manualer

Boss

Boss BC-1X Manual

16 December 2024
Boss

Boss Super Chorus CH-1 Manual

16 December 2024
Boss

Boss Bass Equalizer GEB-7 Manual

16 December 2024
Boss

Boss Turbo Distortion DS-2 Manual

16 December 2024
Boss

Boss Multi Overtone MO-2 Manual

16 December 2024
Boss

Boss Tera Echo TE-2 Manual

16 December 2024
Boss

Boss Metal Core ML-2 Manual

16 December 2024
Boss

Boss Delay DM-2W Manual

16 December 2024
Boss

Boss NS-1X Manual

17 November 2024
Boss

Boss GT-1B Manual

17 November 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlona

Atlona AT-DVIF30S-IR Manual

29 December 2024
Atlona

Atlona AT-PRO3HD66M Manual

29 December 2024
Atlona

Atlona AT-3GSDI500 Manual

29 December 2024
BlueBuilt

BlueBuilt BBMAG2M Manual

29 December 2024
Atlona

Atlona AT-3GSDI-14 Manual

28 December 2024
Atlona

Atlona AT-COMP10SS Manual

28 December 2024
Atlona

Atlona AT-2VGA300SL Manual

28 December 2024
Atlona

Atlona AT-HD-V216 Manual

28 December 2024
Atlona

Atlona AT-VGA11S Manual

28 December 2024
True

True TC900 Manual

28 December 2024