BOYA BY-WM6S Manual

BOYA Mikrofon BY-WM6S

Læs nedenfor 📖 manual på dansk for BOYA BY-WM6S (2 sider) i kategorien Mikrofon. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Instruction Manual

BY-WM6S

UHF Wireless Microphone System

UHF无线麦克风系统

Instruction

Thank you for purchasing BOYA BY-WM6S!

The BOYA BY-WM6S is a new generation UHF wireless microphone

system, compatible with smartphone, tablet, DSLR camera, camcorder,

audio recorder and more.

With low-interference capacity and UHF transmission with true-diversity

reception, it helps users guard against many kinds of troubles, even

under dicult shooting conditions, and delivers the broadcast sound

quality and integrity of audio.

It runs on built-in rechargeable batteries or powered by Type-C DC 5V.

This system is designed with a compact and rugged housing and a

detachable antenna that easily carries to indoor and outdoor environments.

Transmitter Receiver

1. Antenna

2. LINE IN

3. Microphone input

4. Power indicator

5. AUDIO indicator

6. LCD display

7. Power/Mute button

8. SET button

1) Long press the power of the transmitter ON or OFF.

2) Short press to mute

For details, please refer to "LCD display Operation Guide"on page 8

Notes: “√” means the LED light is on. “×” means the LED light is o.

For details, please refer to "LCD display Operation Guide"on page 8

Connect the supplied lavalier microphone here. Fully insert the

microphone’s 3.5mm TRS plug and make sure it clicks into place,

then lock the plug. To remove, release the locking mechanism,

then pull the plug out.

BackFront

(3.5mm diameter stereo mini jack)

Connect one end of the supplied stereo 3.5mm TRS to TRS

or XLR to XLR Male output cable here, and the other end to

the microphone input on a DSLR camera, camcorder, mixer,

or amplier etc.

For more details about LED indicator, please refer to as following:

9. + (+ selection)/ – (- selection) buttons

10. Belt clip

11. USB Type-C charging port

1. Antenna

2. Headphone output

3. LINE OUT

4. Power LED

5. RF indicator

6. LCD display

7. Power button

8. SET button

Long press the power of the transmitter ON or OFF.

Press these buttons to set the transmission channel, volume and

light setting.

Channel / Volume / Light setting

Press these buttons to set the transmission channel, light setting.

Channel / Light setting

9. + (+ selection)/ – (- selection) buttons

10. Belt clip

11. USB Type-C charging port

Back

Bottom

Front

Backlight

- Press the +/-(+/-selection) button to turn LCD backlight ON/OFF.

- Light delay setting includes 10/30/60s options.

Attaching the shoe mount adapter

1. Please attach the belt clip in the direction of the shown picture before

attaching the shoe mount adapter.

2. Slide the adapter down tting into the space between the belt clip

and the receiver.

3. Make sure the adapter insert into vertical slot in parallel until it properly

xs into the horizontal groove and locks.

- This indication shows the battery is charging.

Setting the Transmitter and the Receiver

To connect the transmitters and the receiver, follow these steps:

1. Make sure the supplied lavalier microphones are connected to the

transmitter microphones input or plug a line-level source into the

transmitter line input.

2. Turn on the transmitters and the receiver.

3. Set the transmitters and the receiver to the same channel. If you

are experiencing interference or noise on one channel, try a

dierent channel.

4. When the headphone volume low, plug your headphones into the

receiver and gradually raise the level to a comfortable volume for

monitoring the transmission.

5. The Channel and Volume of the Transmitter and the Receiver are

default value when turn on them for the rst time.

- Adjust channel as you need.

- Adjust as necessary to make sure an ample level is being transmitted

to the receiver.

- The objective is to transmit the highest level without distortion for

the best signal-to-noise ratio throughout the signal path.

6. Once you have determined the transmission quality and level are

good, mount the transmitter and the receiver.

NOTE:

If you are connecting the receiver to a sound system, mute the sound

system. Do not monitor with the headphones at the stage. Anytime you

are changing the channel, remove your headphones and mute connected

sound systems to avoid audible RF noise bursts.

The consists of one body-pack transmitter (TX6S), BY-WM6S

a portable receiver (RX6S), and their accessories as following:

Omni-directional lavalier

microphone

3.5mm TRS to TRS audio output cable

Type-C to USB-A connect cable (x2)

Body-pack transmitters(TX6S) (1) Portable receiver(RX6S) (1)

3.5mm TRS to XLR Male

Output Cable

Microphone clip

Cold-shoe mount adapter3.5mm TRS to TRRS audio output cable

Wind screen Belt clip (x2)

What’s dierence?

For cameras, camcorders, audio recorders and other audio/video

recording devices.

USB Type-C to USB-A charging cable

- Using this cable, the devices with USB-A output can deliver power

to BY-WM6S.

③

The end of XLR is connected to audio devices with a standard

XLR input, such as mixer, amplier, and more.

②

①

Connecting the transmitter and receiver

Using the microphone with smartphone, tablet, Mac

or laptop with combo headphone/Mic jack.

Receiver

1. Mount receiver to smartphone, tablet, Mac or laptop.

2. Using TRRS cable, plug the 3.5 mm connector (straight plug) into the

audio jack of your smartphone.

3. Insert the 90° plug of the connecting cable into the receiver

“LINE OUT” jack.

4. Insert earphone into receiver “ ” for monitoring sound if you need.

5. Long press the power ON/OFF button (the “POWER” indicator

will light in blue)

Caution: Please do not mix up plug, for details, please refer to”

What’s dierence” on page 7.

NOTE:

Not all Android devices support external microphone when taking

video, and you may need to download a third-party app and set up

sound source as external microphone.

If you have any problem using the BY-WM6S components, use the

following checklist. If any problem persist, please consult our local

dealer, or contact us directly.

Using the microphone with cameras, camcorders,

audio recorders and other audio/video recording

devices.

Using the microphone with camcorders and other

XLR recording devices.

Troubleshooting

Receiver

1. Mount receiver to cameras, camcorders, audio recorders and other

audio/video recording devices.

2. Using TRS cable, plug the 3.5 mm connector into the audio jack of

your camera.

3. Insert the other end of the connecting cable into the receiver

“LINE OUT” jack.

4. Insert earphone into receiver “ ” for monitoring sound if you need.

5. Long press the power ON/OFF button (the “POWER” indicator

will light in blue)

- Please make sure the antenna is oriented to the subject getting the

best signal.

1. Mount receiver to camcorders and other XLR audio/video recording

devices.

2. Using the supplied XLR cable, plug the terminal of XLR connector

into the audio jack of your camcorder.

3. Insert the other end of the connecting cable into the receiver

“LINE OUT” jack.

4. Insert earphone into receiver “ ” for monitoring sound if you need.

5. Press the power ON/OFF button ( the “POWER” indicator will light

in blue)

- Please make sure the antenna is oriented to the subject getting

the best signal.

Status Cause Measure

The units does

not turn on.

The batteries

become drained

quickly.

There is no sound.

The sound is weak.

There is distortion

in the sound.

The batteries of BY-WM6S TX

exhausted.

The BY-WM6S components is being

used under extremely cold conditions.

The BY-WM6S Pro components is

being used under extremely hot

conditions.

There are in dierent channel on both

transmitter and receiver.

Use the supplied USB Type-C

cable to charge it.

The batteries drain quickly under

extremely cold conditions.

The batteries drain quickly under

extremely hot conditions.

Keep the same channel on both

the transmitter and receiver.

There do not have a good connection

with the lavalier.

There do not have a well connection

with the earphone.

The input level of the receiver is low.

Insert the lavalier incorrectly into the

LINE IN jack.

The input level of the receiver is

inappropriate.

There are in dierent channel on both

transmitter and receiver.

Headphones with a monaural

mini jack is used.

Please try to reconnect it again.

The input level of the transmitter

is low. Adjust the audio output

level on the transmitter. Keep this

level as high as possible without

distortion to reach best Sound

and Noise Ratio.

Pull it out and reconnect to the

MIC IN jack.

Adjust the audio output level on

the transmitter. Keep this level as

high as possible without distortion

to reach best Sound and Noise

Ratio.

Keep the same channel as both

the transmitter and receiver.

Use the headphones with a

stereo mini jack.

Status Cause Measure

The audio is noisy

or distorted.

This situation

can include

dropouts, white

noise, bursts,

pops and clicks.

Too much

ambience is

being picked up.

RF interference

RF signal is weak.

The input level on the camera,

recorder, or mixer is too high.

When using an omnidirectional

microphone like the one

included with this system, the

microphone may be picking up

too much ambience.

There can be a lot of RF

interferenceoutdoors.

Try moving indoors, where there

is less RF interference.

Overhead telephone lines,

uorescent lighting, and metal

fences can all cause interference.

Turn o all nearby computers and

mobile phones."

Make sure there is an

unobstructed line of sight

between the transmitterand the

receiver.

Keep in mind that your body,

clothes, and onstage sets are

possible obstructions.

If there are obstructions, you

may need to move closer.

Turn down the audio input level

on your camera or recording

devices.

Turn down the audio output level

on the receiver.

Turn down the gain level on mixer.

Make sure the microphone is as

close as to the subject as possible.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

Warning: Changes or modications to this unit not expressly approved

by the party responsible for compliance could void the user’s authority to

operate the equipment.

NOTE: “This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmfulinterference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the

equipment o and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC STATEMENT:

RF warning statement:

The device has been evaluated to meet general RF exposure requirement.

The device can be used in portable exposure condition without restriction.

Specications

Features

④

For more details about LED indicator, please refer to page 5.

LCD Display Operation Guide

Receiver

Lock function

Mute function Charging status

CH 23 556.710MHz

Light ON

Light OFF

Light Delay 10s

Light Delay 30s

Light Delay 60s

CH 23 556.710MHz

1. Signal level

2. Volume setting (1-16)

- Press the SET button to volume setting

- Press the +/- (+/- selection) button to adjust volume.

3. Battery indication

4. Channel number (1-48)

5. Frequency

1. MUTE button

- Press the SET button to mute on.

- When the icon show " ", mute function is on.

2. Battery indication

3. Channel number (1-48)

4. Frequency

Transmitter

123456

798 11 12 1310

1514 16 17 18

Press + & -

to unlock

- LCD will be locked automatically in 30 seconds.

- Long press bottoms “+” and “-“ to unlock.

- Transmitter is mute on.

PLL synthesizer

556.710-575.980MHz

+/-5KHZ(-60dBV, 1KHz input)

82dB or more

10mW

0.1% or less

1/4λ wire antenna

30mW(16 ohm)

-98dBm

40Hz to 18KHz (+/-3dB)

-60dBV (MIC input. 0dB attenuation)

Built-in Li-ion battery 1600mAh

DC5V (USB TYPE-C)

Continuous time: 10 hours, Charging time: 2.5 hours (5V/1A)

60x24x90mm (2.4”x0.9”x3.5”)

149g (5.3oz)

Channel number

Oscillator type

Carrier frequencies

Reference deviation

Signal to noise ratio

RF output power

Distortion

Antenna

Headphone output level

Receive sensitivity

Frequency respose

Reference audio input level

Power requirement

Dimensions

Weight

Mute On

Status LED

The transmitter and the

receiver is connected

The transmitter and the

receiver is disconnected

The transmitter and the

receiver is connected.

And muting function is

on.

The transmitter or the

receiver is in low power

The transmitter or the

receiver is in charging

Transmitter

Receiver

Transmitter

Receiver

Transmitter

Receiver

Transmitter

Receiver

Transmitter

Receiver

√

Flashes blue

√

Stays red

Flashes red

“POWER” “AUDIO” “RF”

• For mobile journalist, vlogger, lmmaker and videographer

• Compatible with smartphone, tablet, DSLR camera, camcorder,

audio recorder

• Deliver clean and broadcast-quality sound for recording

• UHF transmission with 48 channels

• Omnidirectional lavalier microphone included

• Easy-to-read LCD displays

• USB Type-C ports for battery recharging

• Rugged all-metal construction

• Up to 70m (230’)(without obstacle) operation range

• Mute function

• 3.5mm headphone output

品牌长丰型号

变更日期变更担当变更内容版本修改名称

1 2

BY-WM6S说明书内容更新 2020-4-23 吴蒙蒙V01

BOYA BY-WM6S

技术要求:

1、表面无色差

2、无正负公差

3、包装标注尺寸为内尺寸

3.5 mm TRRS connector

- For Smartphone, tablet, Mac or laptop with combo

headphone/mic jack

Connect to

Receiver “LINE OUT” Connect to Smartphone

4-pole plug

3-pole plug

Produkt Specifikationer

Mærke:	BOYA
Kategori:	Mikrofon
Model:	BY-WM6S

Har du brug for hjælp?

Hvis du har brug for hjælp til BOYA BY-WM6S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon BOYA Manualer

BOYA BY-V4 Manual

30 September 2024

BOYA BY-WM3T Manual

30 September 2024

BOYA BY-PM700 PRO Manual

29 September 2024

BOYA BY-WM4 PRO-K6 Manual

9 September 2024

BOYA BY-DM500 Manual

4 September 2024

BOYA link A1 Manual

1 September 2024

BOYA link A2 Manual

1 September 2024

BOYA BY-XM6-K2 Manual

1 September 2024

BOYA BY-XM6-K1 Manual

1 September 2024

BOYA link Manual

1 September 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

Elgato Wave Panels Manual

16 November 2024

Warm Audio WA-8000 Manual

15 November 2024

Pyle PDWM3100 Manual

15 November 2024

Behringer TM1 Manual

15 November 2024

Yamaha RM-WCH-8 Manual

14 November 2024

Yamaha RM-WOH Manual

14 November 2024

M-Audio AIR 192|4 Vocal Studio Pro Manual

13 November 2024

ORCA OR-78 Manual

12 November 2024

Behringer CB100 VIOLIN Manual

10 November 2024

Behringer ECM PRO Manual

10 November 2024