Brother AE2500 Manual

Brother Symaskine AE2500

Læs nedenfor 📖 manual på dansk for Brother AE2500 (2 sider) i kategorien Symaskine. Denne guide var nyttig for 22 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Using Your Sewing

Machine CAUTION

●Always turn off the machine before

you change the needle. Otherwise,

injuries may occur if the foot

controller is accidentally pressed

and the machine starts sewing.

●Only use sewing machine needles

for home use. Other needles may

bend or break and cause injury.

●Never sew with a bent needle. A

bent needle will easily break and

cause injury.

Replacing the needle

■Checking the needle

Slower

Faster

CAUTION

●Make sure you insert the needle until it

touches the stopper, and securely tighten

the needle clamp screw with a screwdriver,

otherwise the needle may break or the

machine may be damaged.

Parallel space

Level surface

Turn the screw counterclockwise.

With the at side of

the needle toward the

back of the machine,

insert the needle until

touching this stopper.

Tighten the

needle clamp

screw.

Note

●

Do not use excessive

force when loosening

or tightening the needle

clamp screw.

XH2149-001

•To sew in reverse, push the

reverse sewing lever in as far

as possible and hold it in that

position while you lightly push

the foot controller.

• To sew forward, release

the reverse sewing lever.

The machine will then sew

forward.

•The length of reverse stitches

is xed at 2 mm (1/16 inch).

Reverse sewing

lever

Changing the presser foot

Sewing thin fabrics

Use a piece of fabric and thread

that are the same as those used

for your project, and check the

thread tension and stitch length

and width.

Trial sewing

Stop the machine with the

needle in the fabric at the

point where you want to

change the sewing direction,

and then raise the presser

foot lever. Using the needle

as a pivot, turn the fabric,

lower the presser foot lever,

and then continue sewing.

Changing the sewing direction

Sewing stretch fabrics

Reverse sewing

When sewing thin

fabrics, the stitching

may become misaligned

or the fabric may not

feed correctly. If this

occurs, place thin paper

or stabilizer material

under the fabric and

sew it together with the

fabric. When you have

nished sewing, tear off

any excess paper.

First, baste the pieces

of fabric together,

and then sew without

stretching the fabric.

Basting

Stitching cylindrical pieces

CAUTION

●Always turn off the machine before you change

the presser foot. If you leave the power on and

step on the controller, the machine will start and

you may be injured.

●Always use the correct presser foot for the

stitch pattern you have chosen. If you use the

wrong presser foot, the needle may strike the

presser foot and bend or break, and may cause

injury.

●Only use presser feet that have been designed

to be used with this machine. Using any other

presser foot may cause accident or injury.

If the fabric does not

t easily under the

presser foot, raise

the presser foot lever

even higher to bring

the presser foot to its

highest position.

Sewing thick fabrics

CAUTION

If fabric more than 6 mm (15/64 inch) thick is

sewn or if the fabric is pushed with too much

force, the needle may bend or break.

Mark on the wheel points up to raise

the needle.

■Presser foot installation orientation

CAUTION

●If the presser foot is

not installed with the

correct orientation, the

needle may strike the

presser foot, which

may bend or break

the needle and cause

injury.

CAUTION

●If the stitches are bunched

together, lengthen the stitch

length and continue sewing.

Do not continue sewing

without lengthening the stitch

length, otherwise the needle

may break and cause injury.

Stabilizer material

or paper

The main parts

■Flat bed attachment

The accessories can be stored in a compartment inside the at bed attachment.

Slide the

attachment to the

left to open.

Storage compartment

Thread tension

Stitch length dial

■Correct tension

Correct tension is important as too

much or too little tension will weaken

your seams or cause puckers on

your fabric.

Lower thread

Upper thread

Surface of

fabric

Back of fabric

■Upper tension is too tight

Loops will appear on the surface of the fabric.

Note

●If the bobbin thread was incorrectly threaded, the

upper thread may be too tight. In this case, refer to

“1 Lower threading” on the back side to rethread

the bobbin thread.

Solution: Reduce the tension by turning the upper

tension control dial to a lower number.

Upper

thread Lower

thread

Loops appear on

surface of fabric

Back of fabric

Surface

of fabric

Solution: Increase the tension by turning the upper

tension control dial to a higher number.

Upper

thread Lower thread

Back of fabric

Note

●If the upper thread was incorrectly threaded, the

upper thread may be too loose. In this case, refer to

“2 Upper threading” on the back side and rethread

the upper thread.

Surface

of fabric

■Upper tension is too loose

Loops appear on the back of the fabric.

Loops appear

on back of

fabric

The tension of the thread will affect the quality of your stitches. You may need to adjust it when you change fabric or thread. We recommend that you do a test sample on

scrap of a fabric before you start to sew.

Depending on the selected stitch, you may need to adjust the stitch

length for best results.

The numbers marked on the stitch length dial represent the stitch

length in millimeters (mm) (1/25 inch).

THE HIGHER THE NUMBER, THE LONGER THE STITCH. With the

“0” setting, material is not fed. This is used when sewing a button.

The “F”-“1” range is for making a satin stitch (closed zigzag stitch),

which is used for making buttonholes and decorative stitches. The

position needed for making the satin stitch varies according to the

material and thread being used. To determine the exact dial position,

rst test the stitch and length settings on a scrap piece of fabric to

observe the feeding of the material.

This snaps in

to the shank.

Press the black button at the

back of the presser foot holder

to release the presser foot.

Install the twin needle in the

same way.

9For repair or adjustment:

• If the light unit (light-emitting diode) is damaged, it must be

replaced by authorized Brother Service Center.

• In the event a malfunction occurs or adjustment is required,

rst follow the troubleshooting table in the back of the operation

manual to inspect and adjust the machine yourself. If the problem

persists, please consult your local authorized Brother Service

Center.

Use this machine only for its intended use as described in this manual.

Use accessories recommended by the manufacturer as contained in

this manual.

The contents of this manual and specications of this product are

subject to change without notice.

For additional product information, visit our web site at www.brother.

com

SAVE THESE INSTRUCTIONS

This machine is intended for household use.

FOR USERS IN COUNTRIES EXCEPT

CENELEC COUNTRIES

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

FOR USERS IN CENELEC COUNTRIES

This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack

of experience and knowledge if they have been

given supervision or instruction concerning use of

the appliance in a safe way and understand the

hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall

not be made by children without supervision.

FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS

ONLY

IMPORTANT

• In the event of replacing the plug fuse, use a fuse approved by

ASTA to BS 1362, i.e. carrying the mark, rating as marked on

plug.

• Always replace the fuse cover. Never use plugs with the fuse cover

omitted.

• If the available electrical outlet is not suitable for the plug supplied

with this equipment, you should contact your authorized Brother

Service Center to obtain the correct lead.

Operation

Manual

Sewing Machine

Please read these safety instructions before attempting to use the

machine.

DANGER

- To reduce the risk of electric shock:

1Always unplug the machine from the electrical outlet

immediately after using, when cleaning, when making any

user servicing adjustments mentioned in this manual, or if you

are leaving the machine unattended.

WARNING

To reduce the risk of burns, re, electric shock, or injury to persons.

2Always unplug the machine from the electrical outlet when

making any adjustments mentioned in the instruction manual:

• To unplug the machine, switch the machine to the symbol “O”

position to turn it off, then grasp the plug and pull it out of the

electrical outlet. Do not pull on the cord.

• Plug the machine directly into the electrical outlet. Do not use

an extension cord.

•Always unplug your machine if the power is cut.

3Electrical Hazards:

• This machine should be connected to an AC power source

within the range indicated on the rating label. Do not connect it

to a DC power source or inverter. If you are not sure what kind

of power source you have, contact a qualied electrician.

• This machine is approved for use in the country of purchase only.

4Never operate this machine if it has a damaged cord or plug,

if it is not working properly, if it has been dropped or damaged,

or water is spilled on the unit. Return the machine to the nearest

authorized Brother dealer or service center for examination,

repair, electrical or mechanical adjustment.

• While the machine is stored or in use if you notice anything

unusual, such as an odor, heat, discoloration or deformation, stop

using the machine and immediately unplug the power cord.

• When transporting the machine, be sure to carry it by its handle.

Lifting the machine by any other part may damage the machine or

result in the machine falling, which could cause injuries.

• When lifting the machine, be careful not to make any sudden or

careless movements, otherwise you may injure your back or knees.

5Always keep your work area clear:

• Never operate the machine with any air openings blocked. Keep

ventilation openings of the machine and foot control free from the

build up of lint, dust, and loose cloth.

•Do not store objects on the foot controller.

• Do not use extension cords. Plug the machine directly into the

electrical outlet.

• Never drop or insert any object into any opening.

• Do not operate where aerosol (spray) products are being used or

where oxygen is being administered.

•Do not use the machine near a heat source, such as a stove or

iron; otherwise, the machine, power cord or garment being sewn

may ignite, resulting in re or an electric shock.

•Do not place this machine on an unstable surface, such as

an unsteady or slanted table, otherwise the machine may fall,

resulting in injuries.

6Special care is required when sewing:

• Always pay close attention to the needle. Do not use bent or

damaged needles.

• Keep ngers away from all moving parts. Special care is required

around the machine needle.

• Do not turn on the machine while pressing down the foot controller.

The machine may start unexpectedly and cause personal injury or

damage to the machine.

• Switch the machine to the symbol “O” position to turn it off when

making any adjustments in the needle area.

• Do not use a damaged or incorrect needle plate, as it could cause

the needle to break.

• Do not push or pull the fabric when sewing, and follow careful

instruction when freehand stitching so that you do not deect the

needle and cause it to break.

7This machine is not a toy:

• Your close attention is necessary when the machine is used by or

near children.

• The plastic bag that this machine was supplied in should be kept

out of the reach of children or disposed of. Never allow children to

play with the bag due to the danger of suffocation.

• Do not use outdoors.

8For a longer service life:

• When storing this machine, avoid direct sunlight and high humidity

locations. Do not use or store the machine near a space heater,

iron, halogen lamp, or other hot objects.

• Use only neutral soaps or detergents to clean the case. Benzene,

thinner, and scouring powders can damage the case and machine,

and should never be used.

•Always consult the operation manual when replacing or installing

any assemblies, the presser feet, needle, or other parts to assure

correct installation.

Please visit us at where you can get the http://s.brother/cpmaa/

support information (Instruction Videos, FAQs, etc.) for your Brother

product.

Be sure to read this document before using the machine.

We recommend that you keep this document nearby for future reference.

Product Code: 888-X03/X13/X23

IMPORTANT SAFETY

INSTRUCTIONS

Shank

Black

button

Presser foot holder

Stitch length dial

Stitch

length dial

Shorter Longer

Slide the at bed attachment to

the left to release it.

Slide the part that you wish to sew onto the arm, and then sew from

the top.

Note

●When you are nished with

free-arm sewing, install the

at bed attachment back in

its original position.

CAUTION

●Before replacing the needle, place

fabric or paper under the presser foot

to prevent the needle from falling into

the hole in the needle plate.

Upper tension-control dial

a Bobbin winder

This winds the thread onto the bobbin for use as the lower thread.

b Stitch length dial

Rotate the dial to control the stitch length.

c Spool pin

This holds the spool of thread.

d Upper tension-control dial

This controls the tension of the upper thread.

e Thread guide

This is used when winding the thread onto the bobbin and then

threading the machine.

f Thread take-up lever

g Thread cutter

Pass the threads through the thread cutter to cut them.

h Flat bed attachment with accessory compartment

i Presser foot

j Reverse sewing lever

Push this lever to stitch in the reverse direction.

k Pattern selection dial

Rotate the dial in either direction to choose the stitch you want.

l Handwheel

Used to manually raise and lower the needle.

m Buttonhole ne-adjustment screw

n Air vent

The air vent allows the air surrounding the motor to circulate.

Do not cover the air vent while the machine is being used.

oMain power and sewing light switch

You can turn the main power and sewing light switch on and off.

p Foot controller jack / socket

Plug in the foot controller plug and connect the machine to the power

supply.

q Presser foot lever

Used to raise and lower the presser foot.

r Handle

Carry the machine by its handle when transporting.

s Foot controller

You can use this to control the sewing speed, and to start and stop sewing.

Slower

Faster

Note

(For U.S.A. only)

●

Foot Controller: Model KD-1902

This foot controller can be

used on the machine with

product code 888-X03, 888-X13

and 888-X23.

The product code is mentioned

on the machine rating plate.

WARNING

●

Use only regular household electricity for the power source. Using other power

sources may result in re, electric shock, or damage to the machine.

●

Make sure that the plugs on the power cord are rmly inserted into the

electrical outlet and the power supply jack on the machine. Otherwise, a re or

electric shock may result.

●

Do not insert the plug on the power cord into an electrical outlet that is in poor

condition.

●

Turn off the main power and remove the plug in the following circumstances:

•

When you are away from the machine

•

After using the machine

•

When the power fails during use

•

When the machine does not operate correctly due to a bad connection or a

disconnection

•

During electrical storms

CAUTION

●

Use only the power cord included with this machine.

●

Do not use extension cords or multi-plug adapters with many other appliances

plugged in to them. Fire or electric shock may result.

●

Do not touch the plug with wet hands. Electric shock may result.

●

When unplugging the machine, always turn off the main power rst. Always

grasp the plug to remove it from the outlet. Pulling on the cord may damage

the cord, or lead to re or electric shock.

●

Do not allow the power cord to be cut, damaged, modied, forcefully bent,

pulled, twisted, or bundled. Do not place heavy objects on the cord. Do not

subject the cord to heat. These things may damage the cord and cause re

or electric shock. If the cord or plug is damaged, take the machine to your

authorized Brother Service Center for repairs before continuing use.

●

Unplug the power cord if the machine is not to be used for a long period of

time. Otherwise a re may result.

Note

●If a power outage occurs while the sewing machine

is being operated, turn off the main power and

unplug the power supply cord. When restarting the

sewing machine, follow the necessary procedure

to correctly operate the machine.

(For U.S.A. only)

●This appliance has a polarized plug (one blade

wider than the other). To reduce the risk of electric

shock, this plug is intended to t in a polarized

outlet only one way. If the plug does not t fully in

the outlet, reverse the plug.

If it still does not t, contact a qualied electrician

to install the proper outlet. Do not modify the plug

in any way.

■Connecting plugs

■Main power and

sewing light switch

■Foot controller

Press the power switch

toward the “I” mark to turn the

main power and sewing light

on. Press toward the “O” mark

to turn off.

Press the foot

controller down to start

sewing. Take your foot

off the foot controller to

stop sewing.

CAUTION

●Do not allow pieces of cloth

and dust to build up on

the foot controller. Doing

so could cause a re or an

electric shock.

Produkt Specifikationer

Mærke:	Brother
Kategori:	Symaskine
Model:	AE2500

Har du brug for hjælp?

Hvis du har brug for hjælp til Brother AE2500 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Symaskine Brother Manualer

Brother CE1155 Manual

11 November 2024

Brother JS1400 Manual

14 Oktober 2024

Brother DS-140 Manual

2 Oktober 2024

Brother XB2500 Manual

23 September 2024

Brother XN1700 Manual

21 September 2024

Brother ML-900 Manual

15 September 2024

Brother VX-540 Manual

14 September 2024

Brother PR-600 II Manual

2 September 2024

Brother JSL-30 Manual

1 September 2024

Brother Innov-is BE915L Manual

27 August 2024

Symaskine Manualer

Nyeste Symaskine Manualer

Cecotec BelleCouture OverLock Manual

18 November 2024

Hema 12x27.5x26 Manual

16 November 2024

Bernina 1080 Manual

15 Oktober 2024

Bernina 1090 Manual

15 Oktober 2024

Bernina 1130 Manual

15 Oktober 2024

Bernina Artista 640 Manual

15 Oktober 2024

Bernina aurora 440 Manual

15 Oktober 2024

Bernina Activa 125 Manual

15 Oktober 2024

Bernina 717 Manual

15 Oktober 2024

Bernina B550QE Manual

15 Oktober 2024