Brother PT-1230PC Manual

Brother Etiketprinter PT-1230PC

Læs nedenfor 📖 manual på dansk for Brother PT-1230PC (2 sider) i kategorien Etiketprinter. Denne guide var nyttig for 18 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

INTRODUCTION

Thank you for choosing the PT-1230PC. Your new P-touch labeler uses P-touch Editor Lite software, which is already installed on your labeler.

There is no need to install any software or drivers onto your PC in order to make creative labels. This manual includes important precautionary

information and simple instructions for operating your new P-touch labeler. Be sure to read the instructions before use and use the product in ac-

cordance with these instructions. Keep this manual handy for future reference.

Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)

Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA

TEL: (908) 704-1700

declares that the product: Product Name: P-touch Labeler PT-1230PC

Model Number: PT-1230PC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to cor-

rect the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

- Changes or modiﬁ cations not expressly approved by Brother Industries, Ltd. could void the user’s authority to operate the equipment.

- The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital device.

SAFETY PRECAUTIONS

WARNING

CAUTION

General Precautions

• Always use the speciﬁ ed voltage and the suggested AC adapter (AD-24) for this machine to prevent any damage or failure.

• Unplug the power cord immediately and stop using the P-touch labeler during an electrical storm. There may be a remote risk of electric shock from lightning.

• Do not use the AC adapter in places of high humidity such as bathrooms.

• Do not overload the power cord.

• Do not place heavy objects on, or damage the power cord or plug. Do not forcibly bend or pull the power cord. When disconnecting the power cord from the power outlet, al-

ways hold the plug.

• To prevent ﬁ re or electric shock, make sure that the plug is fully inserted to the power outlet. Do not use an outlet that is loose.

• Do not get the machine/AC adapter/power plug wet, such as by handling them with wet hands or spilling beverages on to them.

• Do not disassemble or modify P-touch labeler/AC adapter/batteries.

• Do not use metallic articles, such as tweezers or a metallic pen, when exchanging the batteries.

• Do not throw into ﬁ re or heat up the battery.

• Disconnect the AC adapter, remove batteries and stop using immediately if you notice any abnormal odor, heat, discoloration, deformation or anything unusual while in use, or

in storage.

• To avoid injuries, do not touch the blade of the cutter unit or any metal parts near the print head.

• Do not apply excessive pressure to the cutter lever.

• Remove the batteries and disconnect the AC adapter if you do not intend to use P-touch labeler for an extended period of time.

• Do not use old and new batteries together or mix alkaline batteries with other type batteries, or set the positive and negative end in the wrong position. Otherwise, the batter-

ies may leak or be damaged.

• To prevent damage or breakage, do not drop or hit P-touch labeler/AC adapter.

• Use only the USB cable included with the P-touch labeler.

• Depending on the location, material, and environmental conditions, the label may unpeel or become irremovable, the color of the label may change or be transferred to other

objects. Before applying the label, check the environmental condition and the material.

• Do not use the P-touch labeler in any way or for any purpose not described in this guide. Doing so may result in accidents or damage the machine.

• Use only Brother TZ tapes with this machine. Do not use tapes that do not have the mark.

• Do not clean P-touch labeler with alcohol or other organic solvents. Only use a soft, dry cloth.

• Do not touch the print head with your ﬁ ngers anytime to prevent from a burn. Use a soft wipe (e.g. a cotton swab) when cleaning the print head.

• Do not put any foreign objects into the tape exit slot or AC adapter connector, etc.

• Do not place the P-touch labeler/battery in direct sunlight or rain, near heaters or other hot appliances, in any location exposed to extremely high or low temperatures (e.g. on

the dashboard or in the back of your car), high humidity, or dusty locations.

• Do not try to print labels using an empty tape cassette in the P-touch labeler. Doing so will damage the print head.

• Do not pull the tape being fed from the P-touch labeler, otherwise the tape cassette or P-touch labeler may be damaged.

Open the cassette

cover.

Insert a tape

cassette.

Close the cassette

cover.

Verify that the P-touch labeler is

turned off. Open the cassette cover

as shown by the arrow in the above

illustration while pressing the part

marked "<<".

Insert a TZ tape cassette as shown

in the above illustration.

• Make sure that the end of the tape feeds under the tape

guides.

• If the ink ribbon is loose, use your ﬁ nger to wind the toothed

wheel in the direction of the arrow on the cassette.

• Use only Brother TZ tapes with the P-touch labeler.

• For initial use of the tape, install the tape, press and hold the

power/feed button to feed the tape. Then, push in the tape cut-

ter lever to cut the tape.

Connect the P-touch labeler's power supply.

Insert six new AAA alkaline batteries (LR03),

making sure that their poles point in the

correct directions. Always replace all six

batteries at the same time using brand new

ones.

Auto Power Off Function

When the P-touch labeler is operating on battery power only,

it will turn off automatically if not used for a period of 20 min-

utes. The message “ ” may be Unsafe Removal of Device

displayed depending on the Operating System running on

your PC. Any data being displayed will be saved. When you

turn the labeler back on, click on the Editor Lite icon to re-

sume creating your label.

Connect the USB cable and start P-touch Editor Lite.

Download and install the PT-1230PC’s

driver and P-touch Editor 5.0 from Broth-

er’s website. Connect the P-touch labeler

to your PC when requested during this

installation.

For more information about install-

ing the software, visit http://solu-

tions.brother.com/

If you would like to use the more advanced software that is available for your P-touch labeler,

you are able to download P-touch Editor 5.0 from the Brother web site. This advanced soft-

ware will give you greater label making functionality.

Do not connect the P-touch labeler to your PC before you begin the P-touch Edi-

tor 5.0 installation.

Starting P-touch Editor 5.0

Start

P-touch Editor 5.0.

• Double-click the short-

cut icon on the desktop

(P-touch Editor 5.0).

• Click P-touch Editor 5.0

under All Programs on

the Start menu.

Use

P-touch Editor 5.0.

If you have trouble using

the software, refer to the

help information available

in P-touch Editor 5.0.

Getting Ready

Review the names of P-touch labeler parts.

Install a TZ tape cassette.

The PT-1230PC has 2 mode selector settings - “EL” and “E”. The mode

selector switch is pre-set at the factory to the EL mode, for use with

P-touch Editor Lite. For E mode, you need to download P-touch Editor 5.0

and the required drivers. For details on how to download the P-touch Edi-

tor 5.0, see “Starting P-touch Editor 5.0” below.

Connect the

USB cable.

Turn on the P-touch labeler.

The LED lamp will light up.

Windows® XP User

Windows® 2000 User

Windows Vista® User

Go to and open Removable Disk, then start My Computer

P-touch Editor Lite by double-clicking .PTLITE10.EXE

P o p - u p W i n d o w

Ap p e a r s . Se l e c t

P-touch Editor Lite

and click .OK

Pop-up Window

Appears. Click

P-touch Editor

Lite.

It will take longer than usu-

al to start P-touch Editor

Lite when connecting P-touch

labeler to your computer for the

first time. If the software does

not start automatically when you

connect the machine, you may

launch it from My Computer.

Start P-touch Editor Lite by dou-

ble-clicking .PTLITE10.EXE

For details on using

P-touch Editor Lite,

see the back of this

sheet.

P-touch Editor Lite

starts immediately.

*Microsoft Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and other

countries.

*The name of other software or products used in this document are trademarks or registered trademarks of the respective

companies that developed them.

When using the optional AC adapt-

er (AD-24), insert the plug on the

adapter cord into the adapter jack

on the bottom end of the P-touch

labeler. Insert the plug into the

nearest standard electrical outlet.

Move the mode selector

switch on the back of the

P-touch labeler to the “E”

position before connect-

ing the USB cable.

Do not turn off the power or remove the labeler while

using P-touch Editor Lite.

How to disconnect the P-touch

labeler

Exit P-touch Editor Lite by clicking on the at the top

right.

To disconnect the labeler, click the icon in the computer’s

task bar ( , , or ).

Click Safely remove USB Mass Storage Device.

When The device can be safely removed is displayed,

turn off the P-touch labeler and disconnect the USB ca-

ble.

LED lamp

Power/feed

button

Tape cutter

button

Tape exit slot

AC adapter(optional)

connecter

Mode selector

switch

USB port

Print head

Tape cutter

E L E C TR O NI C L

A B E L IN G S Y S T EM

ST E

T E

T EM

E L E C TR O NI C L A BE L IN G S Y S T EM

USER’S GUIDE

English Printed in China

LW3141001

USER’S GUIDE

www.brother.com

When using

Windows Vista®

When connecting the device for the ﬁ rst time, perform the

scan and then select the Always do this for software and

games check box on the dialog box displayed when the

scan completes. P-touch Editor Lite will start automatically

the next time you connect the P-touch labeler.

Produkt Specifikationer

Mærke:	Brother
Kategori:	Etiketprinter
Model:	PT-1230PC
Vægt:	400 g
Batteriteknologi:	Alkaline
Maksimal opløsning:	180 x 180 dpi
Dimensioner (BxDxH):	53 x 158 x 112 mm
Forbindelsesteknologi:	Kabel & trådløs
Batteritype:	AA
Antal understøttede batterier:	6
Kompatible operativsystemer:	Windows 2000 Professional/XP/Vista
Farve:	Ingen
Standard grænseflader:	USB
Understøttet papirbredde:	3.5, 6, 9, 12 mm
Udskrivningshastighed:	10 mm/sek.
Antal USB 1.1-porte:	1