Byron BY103 Manual


Læs nedenfor 📖 manual på dansk for Byron BY103 (3 sider) i kategorien Dørklokke. Denne guide var nyttig for 32 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3
1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push.
2: Gently twist.
3: The backing plate will unclip.
1
Functions:
4 Selectable Melodies
1: Ding Dong (Repeat) 3: Alarm
2: Westminster 4: Ding Dong Ding
4
To select a melody for the Door Chime
1: Remove the Back Plate from the Bell
Push.
2: Press the Melody Select button.
3:The chime will play the newly selected
sound.
4: Press again to select the next melody.
Note: For Front/Back door setup, select a
different melody in one of the Bell Pushes.
CR2032
Adding Additional Chime/Bell Push:
1: Insert CR2032 battery
(Supplied) into the battery
holder.
2: Make sure the positive side
is facing upwards.
3: Replace back plate.
2
Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.
3
1: Plug Chime into a UK 3pin
socket, 220 – 240V ~ 50Hz.
2: Switch the socket on.
Beep
Beep
1: The Chime will ‘Beep Beep’.
2: Press the Bell Push within
60 seconds to learn the
Bell Push to the chime.
3: The Chime will ring to
confirm setup.
Note: Maximum of 2
Bell Pushes can be learnt to a
single Chime for Front/Back
4
Additional Bell Push
To add an additional Bell Push to the Door Chime kit
1: Unplug the Door Chime and wait for 10
seconds.
2: Plug the Door Chime into the Socket and
switch the socket on.
3: Press both Bell Pushes within 60 seconds, to pair
the additional Bell Push to the Chime.
4: Chime will ring to confirm setup, wait 60 seconds
for Chime to exit the learn mode before repressing the
Bell Push5.
5: For Front/Back door setup, select a different melody in one of the
Bell Pushes - See Melody Selection.
Note: Maximum of 2 Bell Pushes can be learnt to a single
Door Chime.
Front Door
Back Door
New Chime
Additional Chime
To add an additional Chime unit to the Door Chime kit
1: Unplug the NEW Door Chime and wait for 10
seconds
2: Plug the Door Chime into the Socket and switch the socket On.
3: The Chime will ‘Beep Beep’ to indicate that it has entered
the Learn mode.
4: Press the Bell Push within 60 seconds, to pair the additional
Chime to the Bell Push.
5: Chime will ring to confirm setup, wait 60 seconds for the Chime
to exit the learn mode before repressing the Bell Push.
Beep
Beep
BY103
1: Push Button 5: Plug-through Chime
2: Melody Selector 6: Speaker
3: Bell Push Battery
4: Signal Sent LED
1:
2:
4:
:3
6:
5:
3
Plug-in any standard electrical product,
220–240V ~50Hz.
e.g. table light, upto a Max Load of
1000W
Avoid using low voltage Transformers, as
this may reduce the operating range of
the Door Chime
Plug-through Socket:
Melody selection:
Plug-through
Wire Free Chime Kit


Produkt Specifikationer

Mærke: Byron
Kategori: Dørklokke
Model: BY103

Har du brug for hjælp?

Hvis du har brug for hjælp til Byron BY103 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Dørklokke Byron Manualer

Byron

Byron DBY-23512 Manual

4 Oktober 2024
Byron

Byron B432E Manual

4 Oktober 2024
Byron

Byron 10.015.46 Manual

1 Oktober 2024
Byron

Byron DB304 Manual

23 September 2024
Byron

Byron DBY-24112 Manual

23 September 2024
Byron

Byron BY102 Manual

22 September 2024
Byron

Byron B411E Manual

22 September 2024
Byron

Byron 10.020.40 Manual

21 September 2024
Byron

Byron 10.020.06 Manual

10 September 2024
Byron

Byron 7720 Manual

10 September 2024

Dørklokke Manualer

Nyeste Dørklokke Manualer

Friedland

Friedland Evo D3200 Manual

30 December 2025
Emos

Emos P5712 Manual

29 December 2024
Heidemann

Heidemann 70370 Manual

29 December 2024
Heidemann

Heidemann 70613 Manual

29 December 2024
Heidemann

Heidemann 70215 Manual

29 December 2024
Heidemann

Heidemann 70832 Manual

29 December 2024