Café CTD90DP2NS1 Manual

Café Ovn CTD90DP2NS1

Læs nedenfor 📖 manual på dansk for Café CTD90DP2NS1 (24 sider) i kategorien Ovn. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/24
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
• IMPORTANT — Save these
instructions for local inspector’s use.
• IMPORTANT — Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance
requires a qualified installer or electrician.
• Proper installation is the responsibility
of the installer.
• Product failure due to improper installation
is not covered under Warranty.
• Product is for indoor use only.
Installation Instructions
27” & 30” Electric Built-In Wall Ovens
FOR YOUR SAFETY:
WARNING
Before beginning the installation, switch power off at the service panel and lock
the service disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight
on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to
200°F [93.3°C]) generated by the oven.
MATERIALS YOU MAY NEED
Junction Box
Wire Nuts
Strain Relief Clamp for 1/2” Conduit
36” (91 cm) of String
TOOLS YOU MAY NEED
1/8” Drill Bit and Electric or Hand Drill
T20 Screwdriver
Phillips Screwdriver
Wire Strippers
7/16” Nut Driver (combination ovens)
1/4” Nut Driver (30” combination ovens)
ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)
into an approved junction box. A plug and receptacle is NOT permitted on these products.
Questions? Call us at 1.800.432.2737 or visit GEAppliances.com.
In Canada, call 1.800.561.3344 or visit GEAppliances.ca.
1 REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all
packing parts from oven, racks and heating elements. Remove protective film and labels on
the outer door and control panel. Also, remove plastic on trims and panel, all tape around the
oven and any shipping screws securing the oven to the base pad. Open oven door and remove
literature pack and oven racks. Remove the bottom trim from the top of the oven. It will be
installed at the end of the installation process. The trim is wrapped separately and taped to the top
of the unit. Remove pedestal rails from separate box and set aside (30” Double Wall Ovens Only).
Consider recycling options for your appliance packaging material.
2 PREPARE THE OPENING
NOTE: If the cabinet does not have a solid
bottom, two braces or runners must be
installed to support the weight of the oven.
For single ovens, the runners and braces
must support 220 lbs (99 kg). For double and
combination ovens, the runners and braces
must support 400 lbs. (181 kg).
NOTE: If marks, blemishes or the cutout
opening are visible above the installed oven,
it may be necessary to add wood shims
under the runners until the marks or opening
are covered.
NOTE: If the cabinet does not have a front
frame and the sides are less than ¾” (1.9 cm)
thick, shim both sides equally to establish the
cutout width.
DESIGN INFORMATION
SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven
may also be installed side by side, below a countertop, or below specified cooktops. See the label
on top of the oven for approved models.
DOUBLE AND COMBINATION OVEN INSTALLATIONS
A double or combination oven may be installed in a cabinet alone or above a warming drawer.
See the label on top of the oven for approved models.
IMPORTANT: Always refer to individual installation instructions packed with each product for
specific requirements.
Suitable
Bracing
to Support
Runners
2" x 4" (5 cm x 10 cm)
or Equivalent Runners Level
with Bottom of Cutout
and Flush with Sides of Cutout
C
L

Produkt Specifikationer

Mærke: Café
Kategori: Ovn
Model: CTD90DP2NS1

Har du brug for hjælp?

Hvis du har brug for hjælp til Café CTD90DP2NS1 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ovn Café Manualer

Café

Café CSB913P4NW2 Manual

17 November 2024
Café

Café CSB912P2VS1 Manual

30 Oktober 2024
Café

Café CSB913P3VD1 Manual

30 Oktober 2024
Café

Café CSB913P4VW2 Manual

30 Oktober 2024
Café

Café CSB912P2NS1 Manual

17 Oktober 2024
Café

Café CSB923P2NS1 Manual

17 Oktober 2024
Café

Café CSB913M2NS5 Manual

17 Oktober 2024
Café

Café CHS90XM2NS5 Manual

5 September 2024
Café

Café CTD90DP2NS1 Manual

4 September 2024
Café

Café CTS90DP2NS1 Manual

4 September 2024

Ovn Manualer

Nyeste Ovn Manualer

Corbero

Corbero CCHM603W Manual

17 November 2024
GE

GE JVM3670 Manual

16 November 2024
GE

GE JVM1540 Manual

16 November 2024
GE

GE JES1656 Manual

16 November 2024
AEG

AEG BSE988330M Manual

16 November 2024
Gaggenau

Gaggenau BMP251 Manual

16 November 2024
Siemens

Siemens HQ472G0B3 Manual

15 November 2024
Siemens

Siemens HR472G0B3 Manual

15 November 2024
Zanussi

Zanussi ZOFEC0W2 Manual

14 November 2024
Bosch

Bosch HQA534BB3 Manual

14 November 2024