Cateye GE100 Manual


Læs nedenfor 📖 manual på dansk for Cateye GE100 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
ENG
OK
NO!
Horizontal
2
4
3
1
Turn the E-Bike adapter counterclock-
wise to separate the adapter from the
headlight and the bracket holder.
Turn the bracket holder and align the grooves on the
E-Bike adapter to the grooves on the headlight, and turn
clockwise until the adapter stops.
1
WARNING!!!
• Make sure the illumination angle will not dazzle
oncoming traffic, and never position the visor to
the bottom of the headlight.
• Before your trip, please make sure the light is
firmly mounted to the bracket and it lights up.
CAUTION!
• Do not place it within children’s reach.
• Do not remove the E-Bike adapter when the light
is on.
Do not attach the E-Bike adapter if water
droplets, dust, or other foreign matter is attached
to the unit. Also, do not touch the terminals.
Never use a high-pressure hose to clean the light.
Always connect the front and rear light with the
2-core wire.
• The cable exits have to point downwards to keep
the housings waterproof.
• This device is rated IPX4 based on JIS C0920.
Do not immerse the device in water. Doing so
may cause a malfunction. Wipe off any moisture
after using the device in rainy weather.
• If the light unit or parts become dirty with mud,
etc., clean with a soft cloth which is moistened
with mild soap. Never apply paint thinner,
benzine or alcohol; damage will result.
LEGAL INFORMATION
Only road legal in Germany if installed on bicycles with
pedal assist function up to 25 km/h that are also
equipped with a battery charge indicator and function
to switch off the motor to prevent a deep discharge of
the battery to ensure that the lighting function is
available when needed.
SPECIFICATIONS
Light source High-brightness multi-white LED
Temperature range 14˚F – 104˚F (-10˚C – 40˚C)
Waterproof IPX4
E-Bike output compatibility
• Input voltage DC5.5 − 14.5 V
• Power consumption 6.8 W Nominal power(s)
• Cable length Approx. 150 cm (Red: Positive /
Black: Negative)
Dimensions/weight 2-9/16” x 2-31/64” x 51/64
(65.0 x 63.0 x 45.5 mm) /
3.5 oz (94.5 g) (Light unit only)
* The specifications and design are subject to change without
notice.
Design Pat. Pending
Copyright© 2020 CATEYE Co., Ltd.
HLEB570G-200924
1
HL-EB570G
E-BIKE HEADLIGHT
Instruction Manual for
E-Bike Dealers
HOW TO MOUNT TO A BICYCLE
GE100 FEATURES
The GE100 headlight connects directly to the E-Bike drive unit for use. The headlight includes a visor to
direct the light distribution, allowing the unit to be mounted on the top or bottom of the handlebar. See
“Mounting above or below the handlebar” for how to change the mounting position of the E-Bike
adapter. The headlight can also be attached to a cartridge battery (optional) for use as a rechargeable
battery headlight. See “USING THE CARTRIDGE BATTERY (OPTIONAL)” for more information.
Light unit FlexTight™ bracket
(H-34N)
Headlight
Bracket holder
E-Bike adapter
Protective cover GP bracket
Mounted below
Mounted above
1. Mounting the bracket
2. Mounting above or below the handlebar
Wrap the strap around
the handlebar.
Attach the dial. Securely tighten the dial.
Cut
2
3
1
*1
Headlight
Mounting height :
400 – 1200 mm
* This section explains how to mount the light unit
below the handlebar.
Rubber pad
Bracket Strap
Strap
Dial
Screw
CAUTION!:
• Be sure to tighten the dial by hand. When you tighten it too hard with a
tool, the screw thread may be stripped.
• Check the dial and screw (*1) on the bracket periodically, and use them
without any loosening.
• Round off the cut edge of the bracket strap to prevent injury.
The head unit can be mounted on either above or below the
handle by positioning the visor of the head unit to the top.
Bracket holder
E-Bike adapter
Removing
Mounted below Mounted above
Visor
Mounting
CAUTION!:
• When attaching or removing the E-Bike adapter, be sure to hold the headlight to prevent it from
dropping and becoming damaged.
• Do not attach the cartridge battery if water droplets, dust, or other foreign matter is attached to
the unit, and do not touch the terminals.
• Never position the visor to the bottom of the headlight. Doing so will dazzle oncoming traffic.
When mounting the light unit, ensure that
the light will not dazzle other road users.
To adjust the angle, loosen the dial or
the screw (*1) to the point that the
bracket moves slightly, make the
adjustment, and then tighten the screw
to fix the light unit in place.
K 1808
• This instruction manual is intended for
use by E-Bike specialists.
Do not attempt to install this headlight if
you are not experienced with E-Bikes.
Consult your dealer for more information.
• After mounting the headlight, dealers are
expected to explain how to use the light
and to provide this instruction manual to
the customer.
3. Attaching/removing the light
Release button
Click
Slide
Press and hold
RemovingMounting


Produkt Specifikationer

Mærke: Cateye
Kategori: Ikke kategoriseret
Model: GE100

Har du brug for hjælp?

Hvis du har brug for hjælp til Cateye GE100 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Cateye Manualer

Cateye

Cateye AMPP100 Manual

13 November 2024
Cateye

Cateye HL-EL450 Manual

13 November 2024
Cateye

Cateye AMPP200 Manual

13 November 2024
Cateye

Cateye GE100 Manual

13 November 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024