Cleco 120XP ETWB135FR Manual

Cleco Ikke kategoriseret 120XP ETWB135FR

Læs nedenfor 📖 manual på dansk for Cleco 120XP ETWB135FR (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

ATG-7373

SET

ETWB27FR, ETWB135FR, ETWB340FR

ELECTRONIC TORQUE WRENCH WITH ANGLE OPERATING INSTRUCTIONS

SET

UNI M

LCD Display and Button Functions

Select Unit of

Measurement

Value (+) Change ModeAudible

Alert

• On/Off

• Clear

• Exit Current

Setting

Value (-) • Change Torque

or Angle Value

Setting

• Select Option

Displayed

• Select Torque

or Angle Value

1. Power On

1. Verify torque is not being applied to the wrench. Press for 1 second.

Wrench will beep once.

2. The wrench will default to Peak Torque Mode. The last unit of measurement

and last torque setting will display.

3. The wrench is ready to use.

2. Power Off

1. If no torque is applied, wrench will shut off automatically after 180 seconds.

2. To shut off manually, verify torque is not being applied then press for

3 seconds.

3. How to Change Unit of Torque Measurement

1. Power on the wrench as described in .Section 1

2. Press repeatedly to select one of the five torque measurement options:

· Kg-m

· Nm

· Ft-lb

· In-lb

· Kg-cm

3. The wrench is ready to use.

4. How to Set Mode

1. There are five mode options:

• P = Peak Torque (default)

• A = Angle

• PA = Peak Angle

• PCt = Target Torque Alert Setting

• trAc= Tracking Mode (optional)

2. Power on the wrench as described in .Section 1

3. Press repeatedly to scroll through the different modes. “SEL” will

show at the top of the screen to indicate the mode being selected. The

currently selected mode will still show as an option when scrolling through modes.

4. Press to select the new mode. The screen will show the last setting

for the mode selected.

Note: To exit out of setting mode without changing the mode, press . The

current mode and setting will remain unchanged.

5. How to Set Target Torque in “Peak Torque” Mode

1. Power on the wrench as

described in .Section 1

2. Press . The current torque

setting will display on the screen

with “ ” flashing.tor

3. The unit of torque measurement can also be adjusted at this time. Press

to change it if required.

4. Press or to select torque value, then press .

5. The wrench is ready to use.

6. Apply torque and rotate the wrench at a until constant moderate speed

alerted to stop by the handle vibration, beeps and LCD display. The LCD screen

alternates red/green when the “target torque alert” warning starts. When the

target torque is reached the LCD Screen shows solid red.

Note: After reaching the target torque the display will flash for 10 seconds,

then default to the last setting. The next measurement can be taken while the

screen is flashing by applying force again, or by pressing to return to the

last setting.

6. How to Set Angle

1. Power on the wrench as

described in .Section 1

2. Press until the “A” mode is

reached, then press

3. The screen will show the last angle value set.

4. If desired angle is displayed, the wrench is ready to use.

5. If you want a different angle, press again to change the angle

degree. Press or to get to the required angle, then press

6. The wrench is ready to use.

7. Apply torque and rotate the wrench at a until constant moderate speed

alerted to stop by the handle vibration, beeps and LCD display.

8. To take the next measurement press or wait until the display stops

flashing.

Note: After reaching the target angle the display will flash for 10 seconds, then

default to the last setting.

For better accuracy the torque wrench should be rotated between

10 degree/sec – 180 degrees/sec.

UNI

SET

UNI M

SET

UNI M

UNI

SET

UNI M

SET

7. How to Change “Target Torque

Alert” and “Target Angle Alert”

Percentages

1. Power on the wrench as

described in .Section 1

2. Press until the “ ” mode is reached, then press . PCt

3. Current value will display on screen with “ ” sign flashingtor

4. Press or to select when the target torque alert will start. The

target torque alert can start at a maximum of 50% to the target torque value

or a minimum of 15% to the target torque value. For example, if your target

torque is 100 ft-lbs and your target torque alert is set at 50%, the alert will

start when you reach 50 ft-lbs. Press to save.

5. The screen will show “ ” so the target angle alert can be adjusted.Ang

6. Press to change the target angle alert setting. Press or

to select when the target angle alert will start. The target angle alert can

start at a maximum of 90 degrees before the target angle or a minimum of 15

degrees before the target angle. Press to save.

7. The wrench is ready to use.

8. How to Use Pre-Set Torque Values

1. Power on the wrench as

described in .Section 1

2. Press then . the

screen will show the flashing

setting number and the torque value will be displayed.

3. Press or to select the desired pre-set torque value, then press .

4. The wrench is ready to use.

9. How to Change Pre-Set Torque Values

Pre-Set Torque Values can only be

selected in Peak or Peak Angle modes.

1. Power on the wrench as

described in .Section 1

2. Press then . the screen will show the flashing setting number

and the torque value will be displayed.

3. Press or to select the desired pre-set torque value, then press

for 1 second, the flashing setting number will turn into flashing “ ” sign.. tor

4. Now the “ ” sign at the top of the sign will flash. Press or to tor

select the desired torque setting, then press The new Pre-Set Value is

saved into the Pre-Set options.

Press again to set the target torque as to the new Pre-set value.

10. How to Set Torque with Angle

1. Power on the wrench as

described in .Section 1

2. Press until the “PA” mode is

reached, then press .

3. The screen will show last angle

and torque value set.

4. If you want a different torque

value or angle , press again.

5. To change the torque value

press or to get to the

required value, then press .

The screen will show “Ang” sign on

top part of the screen. If the

target angle value previously displayed

is correct, press to exit.

The wrench is ready to use.

6. After setting the torque value, the screen will show “ANG”. Press to review

or change the angle value. Press or to get to the required angle

value, then press again.

7. The wrench is ready to use.

8. Apply torque and rotate the wrench at a until constant moderate speed

alerted to stop by the handle vibration, beeps and LCD display.

Note: After reaching the target torque the wrench will start recording the

angle measurement. After reaching the target torque and target angle the

display will flash for 10 seconds, then default to the last setting. To take the

next measurement press or wait until the display stops flashing.

11. Low Battery Indication

1. 100%-80% High Battery 2. 80%-50% Mid Battery

3. 50%-10% Low Battery 4. Lower than 10% - Flashing

12. Changing Batteries

1. Use AA (Alkaline) Batteries only.

2. Remove Batteries if the torque wrench is not used for an extended period

of time.

3. Unscrew end cap 4. Insert 2 AA (Alkaline) Batteries 5. Replace End Cap

SET

UNI M

SET

lb.ft

SET

UNI M

SET

lb.ft

SET

UNI M

SET

UNI M

SET

lb.in

SET

UNI M

SET

UNI M

SET

UNI M

13. Maximum Capacity Exceeded

1. When the applied torque exceeds

the wrench full-scale capacity the

LCD screen will show red. The

display will show “ovEr”.

2. Verify the calibration of the wrench if you know its capacity has been

exceeded.

14. New - Tracking Mode

1. Power on the wrench as described in section 1.

2. Press to scroll through the different modes.

3. Select “ ” to enter Tracking Mode. There will be a T sign next to the trAc

battery indication.

4. In this mode, there will be no target torque or angle value. The display will

show the real time torque and value applied to the wrench.

5. You may press to reset the angle value to 0.

How to Apply Torque

1. This Electronic Torque Wrench is designed so that when force is properly

applied to the handgrip, a continuous audible signal, the LCD screen display

and vibration in the handle will indicate that the Target Torque or Angle has

been attained. pull beyond this point. DO NOT

Caution: The audible signal, LCD screen display and vibration in the the handle

are indicators that the proper torque or angle have been attained. Over torqu-

ing beyond these signals could cause fastener failure.

2. To properly apply torque, attach socket securely on torque wrench square

drive and position socket on fastener so that tilting will not occur. Grasp the

center of hand grip and apply a slow steady increasing force perpendicular

(90 degrees) to the torque wrench body and perpendicular (90 degrees) to the

center line of the square drive, socket and fastener.

3. Turn the fastener down with a smooth and even force applied to the handle

of the torque wrench. As turning resistance increases, pull more slowly. To

assure accuracy, the fastener must be in motion when the torque measure-

ment is made.

WARNING: Any change from the above procedure will result in a change of

torque being applied. This includes standard torque wrenches, flex-head

torque wrenches, universal joints, and universal sockets. DO NOT USE universal

joints or universal sockets due to the complexity of determining the associated

error. If you need angular access, use a flex-head torque wrench.

Extensions

When it is necessary to use an extension that changes the effective lever

length of the torque wrench, torque being applied will change.

Compute adjustments as follows:

TW - Torque set on Wrench

TE - Torque applied by the extension to the fastener

TW = (TE x L) / (L + E)

TE = (TW x (L + E)) / L

Notice: Socket extension bars that are axially in line with the square drive do

not cause error and need no adjustment.

Apply torque and rotate the wrench at a constant moderate speed until alerted

to stop by the continuous audible signal, the LCD Screen display and handle

vibration.

Certification

This torque wrench was calibrated prior to shipment from the factory within

tolerance limits of:

• Torque (unflexed): +/- 2% CW, +/- 3% CCW from 20% to 100% of capacity

• Angle: (+/- 1% of reading) + (+/- 1 degree @ angular velocity >10 degree/

sec <180 degree/sec) + (+/- 1 degree of test fixture)

Limited Warranty

Until one year from the date of purchase, we will repair any defect in material

or workmanship free of charge. Improper use of these products, including but

not limited to the application of excessive force, will affect performance and

may result in injury. The warranty does not apply to wrenches which do not

function properly or within specified accuracy because of wear, improper or

unreasonable use, damage not resulting from defect or malfunction, or which

have been altered. Calibration is warranted for 90 days. This warranty gives

you specific legal rights, and you may also have other rights which vary from

state to state. For repair or calibration visit www.ClecoTools.com.

Apex Tool Group

2630 Superior Court

Auburn Hills, MI, 48236

1.248.391.3700

www.ClecoTools.com

1.800.845.5629

• Never use the torque wrench with the power off. Always turn on the

torque wrench so the applied torque is measured.

• Do not press any key while torque is being applied.

• Do not use electronic torque wrench to loosen fasteners.

• Verify the calibration of the wrench if you know or suspect its

capacity has been exceeded.

• Periodic recalibration is required to maintain accuracy.

• Never apply more torque than the maximum wrench capacity or the

maximum fastener specifications.

• Do not immerse in fluids.

• Do not use on live electrical circuits.

• Electrical shock can cause injury. Rubber handle is NOT insulated.

WARNING

SET

UNI M

• Color LCD

Screen

Produkt Specifikationer

Mærke:	Cleco
Kategori:	Ikke kategoriseret
Model:	120XP ETWB135FR

Har du brug for hjælp?

Hvis du har brug for hjælp til Cleco 120XP ETWB135FR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Cleco Manualer

Cleco S133410 Manual

23 September 2024

Cleco NeoTek T55-3000020 Manual

23 September 2024

Cleco NeoTek 937731PT Manual

23 September 2024

Cleco 120XP ETWB340FR Manual

23 September 2024

Cleco NeoTek 943462PT Manual

23 September 2024

Cleco NeoTek 942396PT Manual

23 September 2024

Cleco LiveWire 961350PT Manual

23 September 2024

Cleco NeoTek 942391PT Manual

23 September 2024

Cleco LiveWire 942039PT Manual

23 September 2024

Cleco S133411 Manual

23 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron Overbridge Manual

26 November 2024

Elektron Sidstation Manual

26 November 2024

SKROSS World Adapter Pro+ Manual

26 November 2024

SKROSS PRO – World & USB Manual

26 November 2024

SoundTube IPD-RS82-EZ Manual

26 November 2024

Kramer 4x1VB Manual

26 November 2024

Kramer RC-63A Manual

26 November 2024

SoundTube IPD-HP82-EZ Manual

26 November 2024

Kramer RK-KVM-1U-PP3 Manual

26 November 2024

Gioteck VX-2 (PS3) Manual

26 November 2024