Coby TF-DVD7005 Manual

Coby Bærbar DVD-afspiller TF-DVD7005

Læs nedenfor 📖 manual på dansk for Coby TF-DVD7005 (1 sider) i kategorien Bærbar DVD-afspiller. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/1
Please read this manual before connection and use.
TF-DVD7005
Important Safety Instruction
. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute risk of electric shock to persons.
. The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
Dangerous high voltage is present inside the enclosure. Do not open the cabinet.
CAUTION: To prevent electric shock, match wide blade plug to wide slot, and fully insert.
CAUTION: This Digital Video Disc Player employs a laser System. To prevent direct exposure to the
laser beam, do not try to open the enclosure. When open and the interlocks are defeated,
visible laser radiation is present.
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure. DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a digital device. Pursuant with Class B
the These limits are designed to provide reasonable protection against harmful interference FCC Rules,Part 15.
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instruction may cause harmful interference to radio communication.
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS Page
SAFETY INFORMATION
TABLE OF CONTENTS
UNPACKING.............................................................................................................................................................1
NOTE ON DISC........................................................................................................................................................2
VIEWS OF THE MAIN UNIT...................................................................................................................................3-4
VIEWS OF THE REMOTE CONTROL.....................................................................................................................5
CONNECTIONS(Connecting to a TV)......................................................................................................................6
CONNECTIONS(Connecting to a HeadphonePower ..........................................................................................................7
Connections (to AC Adapter)Power
Connections (to DC Car Cord)
CONNECTIONS(Power Connections to Battery Pack).........................................................................................................8
FUNCTION BUTTONS...........................................................................................................................................9-14
SETUP MENU.......................................................................................................................................................15-17
CUSTOM SETUP....................................................................................................................................................17
TROUBLE SHOOTING...........................................................................................................................................18
SPECIFICATIONS...................................................................................................................................................19
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: SHOCK HAZARD-DO NOT OPEN
AVIS: RISOUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
Safety Precautions
Note on Disc
Care of Disc
Disc Requirement
Video disc contains high-density compressed data that needs proper handling.
Hold the disc with fingers. Hold the disc's outer edge and/or the center spindle hole.
Do not touch the disc surface.
Do not bend or press the disc. Do not expose the disc to direct sunlight or heating sources.
Store discs in cabinet vertically, and in dry condition. Prevent exposure to :
Direct sunlight
Heat or exhaust from a heating device.
Extreme humidity.
Clean the disc surface with a soft, dry cleaning cloth. Wipe the disc surface gently and radically from center
toward the outer edge.Do not apply thinner, alcohol , chemical solvent, or sprays when cleaning. Such
cleaning fluids will permanently damage the disc surface.
In addition, this unit can play back a CD-R, or CD-RW that contains audio titles or MP3 files.You cannot playback discs
other than those listed above.(CD-ROM, CD-Extra, CD-G, and CD-l discs can not be played on this DVD player.)
The DVD player can play back the following discs.
Disc mark Contents Disc size Maximum playback time
DVD video
discs Audio+Video
(moving picture)
CD Audio
12cm
12cm/8cm
133 min (SS-SL)
242 min (SS-DL)
266 min (DS-SL)
484 min (DS-DL)
74min/20min
.1. .2.
Unpacking
Please make sure the following items are included with your DVD player. If any items are
missing, contact your dealer.
StepClear
Mute
Remote Control
Battery
RCA Cable Headphones
DC Car Cord
Main Unit Main Unit
Views of the Main UnitViews of the Main Unit
.3. .4. .5. .6.
Step
Clear
Mute
Title
Power
Menu
Enter
Direction buttons
Mute
Numeric buttons
Repeat A-B
Repeat
Audio
SubTitle Angle
Program
PBC
Slow
Step
FF/FB
PREV/NEXT Skip
Zoom
Stop
Play/Pause
Setup
LCD Mode
Display
Views of the Remote Control
Remote Control
Battery Installation
Connections
Connecting to a TV set (TV or monitor with audio/video input)
1. Refer to the owner's manual of your TV as well.
2. Before connecting the DVD player to a TV set, be sure to turn the power off
and unplug both units from the wall outlet.
Audio/Video cable(Supplied)
To AUDIO OUT
To VIDEO OUT To AUDIO/VIDEO
input
Connections
.7. .8.
Connections
Power Connections (to Battery Pack) Basic Playback
Function Buttons
.9. .10.
Function Buttons
.11. .12.
Function Buttons
.13.
Setup Menu Setup Menu
Item Instruction Default setting
.15. .16.
Setup Menu Trouble Shooting
Should your DVD player develop a problem, please check below before requesting service:
Should the player develop a malfunction, unplug the player for 30 minutes. After
that, power on the player and the restore function should reset the player.
Symptom Check and Action
No power 1. Make sure the unit has been powered on manually.
2. Check if the power cord has been properly connected to the power outlet.
3. Make sure the battery pack is fully charged.
Does not play 1. No disc, load a disc.
2. Disc has been loaded upside down. Place the disc with the label side up.
3. Disc's rating level is higher than the player's setting.
4. Disc is incorrect type for the player.
5. Disc is damaged or dirty. Clean the disc or try another one.
6. Moisture may be condensed inside the player. Remove the disc and leave the unit
power on for one or two hours.
No Picture 1. Check if the TV set has been powered on. Use TV remote to select AV signal for
DVD rather than broadcast.
2. Check if the system connection is proper and secure.
3. Check if the connection cables are damaged.
4. Clean the disc.
Picture noisy/
distorted
1. Disc is damaged or dirty. Clean the disc or try another one.
2. Reset the color system of the TV set.
3. Make sure the DVD player is not connected through a VCR, cable or satellite dish.
No sound or sound
output not complete 1. Check if the TV and amplifier have been switched on and correctly set.
2. Check if the TV and amplifier system connections are secured.
3. Press AUDIO button to select other audio tracks of the disc.
4. Check if the MUTE function of the TV or amplifier has been activated.
5. There will be no sound output during REVERSE PLAY/PAUSE/SLOW and
SEARCH.
Remote control
does not work 1. Make sure the POWER button on the unit has been turned on manually.
2. Remove the obstacles between the remote control and the player.
3. Point the remote control towards the remote sensor on the player.
4. Check if the batteries of the remote control have been loaded with correct
polarities.
5. Replace the batteries of the remote control.
Malfunction
.17. .18. .19.
Specification
Video output 1+0.2V (p-p), 75ohm, Negative sync., 3.5 mm mini jack x1
Audio output 1.5 Vrms (1 KHz, 0dB), 3.5 mm mini jack p1-x1
Earphone terminal 3.5mm stereo mini jack x1
Signal /Noise ratio(audio) 90dB typical
Dynamic range(audio) 90dB typical
Panel size 7 inch (16:9)
Resolution 480(H) x 234 (V) (QVGA) Pixels
Laser Wavelength 650 nm
Operating conditions Temperature: 0 c to 35 c. Operation status : Horizontal
Dimensions 187x170x50mm (Main Unit & Batt.)
Weight 937g (Main Unit & Batt. )
Power supply DC 9.0V 2A (AC adapter TERMINAL)
Power consumption <=9w
Signal system NTSC
CAUTION: Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Disconnect the apparatus from the mains if it is not in use.
Please study this manual carefully and always keep it available. There are, however, some installa-
tion and operation precautions which you should be aware of.
(1). Read these instructions.
(2). Keep these instructions.
(3). Heed all warnings.
(4). Follow all instructions.
(5). Do not use this apparatus near water.
(6). Clean only with dry cloth.
(7). Do not block any ventilation openings-Maintain well ventilated conditions around the product. Do not put
product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer's
instructions.
(8). Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
(9). Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
(10). Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus. Power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
(11). Only use attachments or accessories specified by the manufacturer. Do not use attachments not
recommended by the product manufacturer as they may cause hazards.
(12). Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
(13). Unplug this apparatus during lightning storms or when unused for long periods of time. Unplug it from
the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due
to lightning and power line surges.
(14). Power sources-this product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer
or local power company. For products intended to operate from battery power, or other sources, refer
to the operating instructions.
(15). Overloading-do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
Main Unit
MP3
JPEG Still high resolution 600min
Audio 12cm 600min
TFT LCD
Speaker
DC 9V IN
Remote Sensor
Power ON Indicator
Video Out
Audio Out
Headphone Jack
Volume Control
Speaker
Two speakers produce stereo sound.
Remote Sensor
Receiving remote control signal for
operation.
Power ON Indicator
It is green under normal playback.
It is red under STANDBY mode.
Video Out -- Connect to external TV screen by the supplied RCA cables.
Audio Out -- Connect to external speaker system by the supplied RCA cables
Headphone Jack -- Connect to the supplied headphone.
As the headphone is plugged in, the speakers' output will be OFF.
Volume Control -- Adjust to the desired volume level.
Power Switch
Press to turn on the unit.
DC 9V IN
Connect to the supplied AC Adapter/DC Car
Cord for power supply.
TFT LCD
Present high-resolution pictures.
Power Switch
DC 9V IN
Setup
LCD Mode
Play/Pause/Enter
Stop
Up
Down
NEXT/F.F/RIGHT
PREV/F.B/LEFT
Open
Disc Lid
For your reference:
1. Place a disc with the label facing up, and push gently on the center of the disc so it goes into position.
2. To start playing, press the PLAY/PAUSE button. (Some discs will start playing automatically).
3. To stop playing, press the STOP button.
4. To Skip Forward/Skip Backward, press the NEXT/PREV button.
5. To Fast Forward/Fast Backward, press/hold the NEXT/PREV button for about two seconds and
press NEXT/PREV button repeatedly to increase the search speed.
Clear
NOTE The buttons of same descriptions on the main unit/remote control are of same functions.
Refer to the diagram. Open the battery compartment of the
remote control. Insert batteries, and then close the compart-
ment.
To use the remote control, point it at the remote sensor of
the unit and operate in the range of 5 meters and at angle
of 60 degrees.
Generally, the batteries last for about one year. Replace the
batteries if the remote control does not work.
Do not spill water on the remote control.
Do not use remote control for other equipments at the same
time.
Remove the batteries if the remote control will not be in use
for a long period of time.
NOTE
WARNING:
The battery used in this device may present a fire or chemical burn hazard if mistreated.
Do not recharge, disassemble, incinerate, or heat the batteries about 1000C (2120F).
Use of another battery may present a risk of fire or explosion. Dispose of used batteries.
Do not dispose of fire.
Keep batteries out of children's reach.
Connecting to a Headphone Be sure that your unit is at low volume level before
connecting the headphone.
Increase the volume gradually for your
comfortable listening.
CAUTION:
Hearing experts advise against the constant use
of personal stereos played at high volume.
Constant high volume use can lead to hearing loss.
If you experience ringing in the ears or hearing loss,
discontinue use and seek medical advise.
Power Connections (to AC Adapter)
**Do not connect the power cord until all other connections have been made.
AC adapter:
This AC adapter operates on
100-240V~~50/60Hz 2A Min
DC OUT: 9V
DC current: 2.0A Min
To Headphone jack
Headphone
To DC in jack
AC100-240V
Power is supplied through the provided appropriative power adapter, one end of which is connected
to the DC IN jack on the main unit, another to wall outlet with AC100-240V.
Note:
a. If you have difficulty inserting the plug, turn it over and reinsert it.
b. If the unit will not be in use for long periods of time, disconnect the plug from the outlet.
c. In order to prolong the operation life, the intervals of continuous power on should be not less
than 30s.
**For new or exhausted rechargeable battery pack, we recommend it be recharged for 4 hours.
Basic operations on the battery pack
a. Place the battery into its cradle and assign the battery hook to the hole.
b. Hold down the battery to restrain it from spring-up, meanwhile, slide it to arrow direction to lock it .
c. To charge the battery pack, attach the battery pack to the main unit and power on the player
by AC adapter.
d. To remove the battery pack, hold down PUSH/RELEASE button and counter slide the battery.
(NI-MH Rechargeable Battery Pack)
** The battery can be recharged about 300 times without obvious performance drop. **
Note:
a. Use the special charger.
b. Never dispose of in fire or heat up.
c. Do not use in high temperature or near heat sources.
d. Do not open the cover. Refer servicing only to qualified service personnel.
e. Do not charge up the battery pack while the DVD player is working with the battery pack.
f. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type.
Low Battery Detection: The unit will auto stop and turn to STANDBY mode when voltage reaches
too low.
1. Switch on the player
Open the DVD cover by hand.
Slide the POWER switch to "ON" position.
(If close the cover during playback, the LCD display will be OFF for
power saving).
2. Load a disc
Press the OPEN button to open the disc lid and insert a disc with the label up.
Close the disc lid by hand.
If the single sided disc is placed in upside down, " NO DISC " or " BAD DISC " will appear
on the on TV screen.
After playing back all of the chapters in the title, the DVD player stops automatically and shows
the menu screen.
3. Start playback
Press the PLAY button to start playing. (Some discs may play automatically).
If a DVD disc menu appears on screen
Press the DIRECTION buttons to select the desired feature in the menu.
Press ENTER button to confirm a selection in the menu.
4. Adjust the volume
Turn the volume control on main unit to the desired volume level.
Problem disc messages
The following message will be displayed on screen when there is a format problem with loaded disc:
"WRONG REGIONAL DISC"
Region code of the disc is not matching to the player's (region 1 to region 6)
"WRONG PASSWORD"
The rating level of the disc is higher than the rating level setting of the player.
The player will not play the disc.
"WRONG DISC"
The player is equipped with automatic disc quality detection software. When the player detects a
problem or damaged disc, the unit may play the disc at a lower quality or stop completely, depending
on the damaged level of the disc.
POWER management
If the player will not be in use for a long period of time, unplug the player for safety.
Production qualities of DVD discs vary. Some discs may deviate from the industry standard. Some incorrectly
formatted discs may be played. However, the playback and operational quality may be substandard.
Function Buttons Function Buttons
LCD Mode Press it once, the screen displays:
Display
Press the Display button to show the time and status information.
Press Display button the third time to quit the display mode.
Play/Pause
Press the Play button for the first time to play the disc.
Press the button for the second time to pause playing. (Still picture).
Press again to resume playback.
Stop
Press the Stop button once, to stop playback. Press the Play button to resume. Disc will begin
playing from where it was stopped.
Press the Stop button twice, to stop playback. Press the Play button to resume. Disc will begin
playing from the beginning.
Skip Forward/Backward
Press the button to skip advance DVD chapter or CD track
Press the button to skip backward DVD chapter or CD track.
NOTE: Player will not skip forward or backward during "WARNING" section of a DVD disc.
Single chapter DVD or single track CD cannot be skipped.
Fast Forward/Backward
Press the button to fast forward through the disc. Repeatedly pressing the button will increase
the search speed.
Press the button to fast backward through the disc. Repeatedly pressing the button will
increase the search speed.
Press PLAY to resume normal playback.
NOTE: The player is muted during fast forward or fast backward.
The player will not fast forward or fast backward during WARNING section of a DVD disc.
Play X2 X4 X8 X16 X32
Slow
Press SLOW button to play at slow motion. Repeatedly pressing the button will decrease the
slow speed.
NOTE: The player is muted at SLOW mode.
Disc MENU/TITLE
While playing a DVD, press the MENU button to return to the DVD disc start menu.
While playing a DVD, press the TITLE button to return to the title menu.
NOTE: Some DVD discs do not allow the TITLE function.
Select an item in the menu
In the DVD disc start menu or in the Set Up menu
Press the DIRECTION buttons to highlight function icons.
Press the ENTER button to confirm a selection.
Numeric Key Pad
(Random Program access)
1). To directly access a DVD Chapter or a CD track, input the desired DVD Chapter or
CD Track number using the numeric key pad.Then press the ENTER button to
confirm.
2.) Input data for the DVD disc start menu or the player's setup menu.
NOTE: Some DVD discs do not allow direct access function.
MUTE
Press the MUTE button to select mute on or mute off.
ZOOM
PLAYING DVD
Press the ZOOM button repeatedly and the TV screen will display
Press the Direction buttons to move the picture position.
PLAYING JPEG
Press the ZOOM button repeatedly and the TV screen will display:
While at 100%, press the direction button to rotate the picture.
While at 150% or 200%, press the direction button to move the picture position.
NOTE: The picture quality decreases as the picture size increases.
Play X1/2 X1/4 X1/8 X1/16 X1/32
Mute
Zoom
ZOOMx2 ZOOMx4 ZOOMx1
25% 50% 100% 150% 200%
Repeat Section A-B
To repeat playback a specific section of a disc.
Press the A-B button at the starting point of the desired section, "Repeat A" appears on
screen.
Press the A-B button again at the end of the desired section, "Repeat A-B" appears on screen.
The player will start repeating playback the selected section from A to B until the function is
cancelled.
To cancel the function, press the A-B button once more to return to normal playback. " Off"
will appear on screen for few seconds.
NOTE: Some DVD discs do not allow the A-B function playback. This function does not apply to MP3
discs.
REPEAT
This function allows repeated playback of a Title, Chapter, Track or Disc.
Press REPEAT button repeatedly to select the repeat mode.
Playing DVD
Playing CD
Playing MP3
NOTE: Some DVD discs do not allow the REPEAT function.
STEP
Press STEP during playback, one frame of the image is played each time you press the button.
Press the Play button to quit the STEP mode.
AUDIO
: For DVD playback
While playing a DVD disc that contains multiple languages, press the AUDIO button repeatedly
to select the desired language of the audio sound track.
A DVD disc may contain up to 8 selectable audio languages.
The default AUDIO setting is English.
:For CD/MP3 playback
Press the AUDIO button repeatedly to shift among R/R, L/R, and L/L.
The default AUDIO setting is L/R.
NOTE:
If the desired language is not selected even after pressing the button several times, it means
that the language is not available on the disc.
When the power is turned on or the disc is removed, the language heard is the one selected
at the initial settings.
A-B
Repeat
Power Connections (to DC Car Cord)
To the DC 9V In of main unit
To the DC Jack of Car
Plug the DC Car Cord to the DC in Jack for power supply.
Note:
a. Please do not plug it to the battery recharge jack.
b. The DC Car Cord is only for in car use.
Chapter Title Disc Off
Track Disc Off
Step
Audio
Subtitle
While playing a DVD disc that contains multiple subtitles, press the SUBTITLE button
repeatedly to select the desired language of the viewable subtitle.
A DVD disc may contain up to 32 selectable subtitles.
The default SUBTITLE language is ENGLISH.
NOTE:
In some cases, the subtitle language is not changed to the selected one immediately.
When a disc supporting the closed caption is played, the subtitle and the closed caption may
overlap each other on the TV screen. In this case, turn the subtitle OFF.
When the desired language is not selected even after pressing the button several times, it
means that the language is not available on the disc.
CLEAR
Press the Clear button to cancel the incorrect input in DVD program .
SEARCH
Go to a desired section. (A desired Title, Chapter, Time)
Playing DVD
Search by Title/Chapter
a). Press the SEARCH button once,below picture appears:
b). Press the LEFT/RIGHT direction button to highlight the entry.
c). Input the desired title/chapter by numeric keys or use up/down direction button to select.
d). Press the ENTER or PLAY/PAUSE button to execute search.
e). To exit, press SEARCH again.
Search by Time
a). Press the SEARCH button twice, below picture appears:
b). Input Second, Minute and Hour information by the numeric keys.
c). Press the ENTER or PLAY/PAUSE button to execute the search.
d). To cancel the incorrect information you have input, press the Clear button.
e). To exit , press SEARCH again.
Playing CD
Search by Time
a). Press the SEARCH button once, below picture appears:
b). Input Second, Minute and Hour information by the numeric keypad.
c). To cancel the incorrect input, press the Clear button.
d). To execute the search, press ENTER or PLAY/PAUSE. To exit , press SEARCH again.
Sub-
Title
Clear
Search
Various features of the DVD player can be adjusted in the Setup Menu.
1. Press SETUP button.
Then the SETUP menu appears on screen.
2. Press the UP/DOWN button to highlight the desired
item.
3. Press ENTER to confirm.
4. Press the LEFT button to return to upper menu level.
5. To exit from the setup menu, press SETUP once more.
Or press UP/DOWN to select the EXIT menu.
NOTE:
Make sure your player is in STOP mode before setting the SETUP menu, otherwise some setup
features will be unavailable.
--Language Setup--
Press the UP/DOWN button to highlight the desired item from OSD/Menu/Audio/Subtitle, and press
ENTER to confirm.
--Screen Setup--
Press the UP/DOWN button to highlight the desired item from TV Type/Screen Saver/TV System/
Brightness/ Contrast, and press ENTER to confirm.
1. TV Type
Press the UP/DOWN button to select the aspect ratio from 4:3 PS (Pan Scan); 4:3 LB (Letter Box);
16:9 (Wide Screen). And press ENTER to confirm.
This is selected when the unit is connected to a normal TV. Wide-screen 4:3 LB (Letter Box):
images are shown on screen, with black belt on the top and bottom.
This is selected when the unit is connected to a normal TV. Wide-screen images 4:3 PS (Pan Scan):
are shown on screen, with some parts cut automatically.
Menu
Audio
Subtitle
OSD To select the language of the OSD by the UP/DOWN button,
and press ENTER to confirm.
To select the language of the Menu by the UP/DOWN
button, and press ENTER to confirm.
To select the language of the audio sound track by the
UP/DOWN button, and press ENTER to confirm.
Select the language of the subtitle by the UP/DOWN button
and press ENTER to confirm.
When OFF is selected, the subtitle will not be displayed.
English
English
English
English
16:9 (Wide Screen): This is selected when the unit is connected to a wide-screen TV.
The default setting is 4:3 LB
NOTE: Certain DVD discs are formatted in wide screen (16:9) or letter box (4:3) only. Adjusting the
setting of the disc player will not change the screen size for these "Format-only" discs.
2. Screen Saver
Press the UP/DOWN button to shift between Screen Saver ON and OFF. And press ENTER to
confirm.
The default setting is On.
The screen saver is useful to prevent your display from becoming damaged.
If the Screen Saver is set ON, the screen saver picture appears when you leave the DVD player in
stop mode for about a few minutes. Press any button on main unit or remote control to exit from the
screen saver.
Automatic power off function
After the screen saver has been engaged for about a few minutes, the DVD player will automatically
turn itself off, except during CD playback.
3. TV System
Press the UP/DOWN button to select the TV System from NTSC/PAL/AUTO, and press ENTER to
confirm. The default setting is NTSC.
(The TV System for north America is NTSC. Auto should only be used if you have a Multi-System
TV.)
4. Brightness
Press the UP/DOWN button to select your satisfied brightness effect from Normal/Bright/Soft. And
press ENTER to confirm.
.The default setting is Normal
5. Contrast
Press the UP/DOWN button to select your satisfied contrast ratio from -4, -3, -2, -1, 0, 1, 2, 3 and
4. And press ENTER to confirm.
.The default setting is 0
--Custom Setup--
Press the UP/DOWN button to highlight the desired Custom item (Parental Ctrl, Password, Angle
Mark, Default), and press ENTER to confirm.
A). Parental Ctrl
There are eight levels of Parental Control. Level one opens discs to people of all ages. Level
eight is suitable only for adults.
To change the parental control setting, a 4-digit code is required to be input first. (The default
code is 8888.) When the input code is confirmed, the level setting menu will appear. Select
the appropriate level by the UP/DOWN button, and press ENTER to confirm.
B). Password
Move the cursor to the PASSWORD prompt and press ENTER. Input the password 8888 if it is
the first use. After confirmation, you will be required to input a new 4-digit code, and verify again.
WARNING:
Please keep a copy of the new password in a safe place. Otherwise, you will not be able to
change the Parental Control.
Please remember your password, as the DEFAULT setting will revert everything BUT the
PASSWORD and Parental Control to the factory defaults.
C). Angle Mark
Choose between ON and OFF.
The default setting is ON.
When the Angle Mark function is ON, an icon will be displayed on screen if the disc has multiple
angle shots available for viewing.
Press ANGLE on the remote control to enjoy these scenes.
D). Default
This function allows you to change the player back to the factory default settings. All settings will
be changed back to the original settings except the Password and Parental Control.
Track Folder Disc Off
slow
LCD
Mode
LCD
Mode
VOLUME DC 9VPHONE AUDI O VIDEO
VOLUME DC 9VPHONE AUDI O VIDEO
VO LUME DC 9 VPHO NE AUD IO VI DEO
0 03 30 Second
Minute
Hour
Second
Minute
Hour
0 03 30
Function Buttons
.14.
Program
To play a disc in a desired sequence.
NOTE: The Program function is available just as the player is in Navigate Off mode.
Press the PBC button to set Navigate Off.
In DVD mode
NOTE: Some discs do not allow program setting.
Setup
Press the SETUP button to enter the player's setup menu.
The SETUP menu allows the viewer to adjust the setting details of the DVD player.
Please read the "Setup Menu" of the manual for further directions on how to use the SETUP
menu.
Press the Program button to enter the program menu.
Pro-
gram
Setup
Title Chapter
or ENTER button
.
.
Language Setup
OSD
Menu
Audio
Subtitle
Screen Setup
TV Type
Screen Saver
TV System
Brightness
Contrast
Custom Setup
Parental Ctrl
Password
Angle Mark
Default
LCD
Mode
: Move : Select SETUP : Quit
: Move : Select SETUP : Quit
: Move : Select SETUP : Quit
Press up/down direction button to select the
desired item, press left/right direction button to
make adjustment.
When SCREEN is selected, press left/right button
to change screen dimension as 16:9 or 4:3.
When RESET is selected, press Enter button to
confirm, the above three control bar
will be reverted to the default.
ATT AC H
Customer Service Hours
Monday- Friday 8:00AM ~ 11:00PM (EST) 1-800-681-2629 or 718-416-3197
Monday- Friday 6:30PM ~ 11:00PM (EST) 1-800-727-3592
Saturday- Sunday 9:00AM ~ 11:00PM (EST) 1-800-727-3592
Or Send E-Mail to: Customerservice@cobyusa.com / techsupport@cobyusa.com
Program
Program
Program
ON O FF
ON OFF
ON OFF
SCREEN 16:9 4:3
RESET
Brightness
Contrast
Color
or ENTER
or ENTER
AC/DC Adapter Power Cord
D
V
D
/
M
P
3
/
C
D
/P
I
C
T
U
R
E
C
D
P
L
A
Y
E
R
PLAY/PA USE
SETUP
STOP
LC D MOD E
NOTE: 1. Mains plug is used as the disconnect device. It shall remain readily operable and should not
be obstructed during intended use.
2. The rating label is located on the bottom enclosure of the apparatus.

Produkt Specifikationer

Mærke: Coby
Kategori: Bærbar DVD-afspiller
Model: TF-DVD7005

Har du brug for hjælp?

Hvis du har brug for hjælp til Coby TF-DVD7005 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Bærbar DVD-afspiller Coby Manualer

Coby

Coby TF-DVD450 Manual

29 August 2024
Coby

Coby TF-DVD5605 Manual

29 August 2024
Coby

Coby TF-DVD560 Manual

29 August 2024
Coby

Coby TF-DVD7050 Manual

29 August 2024
Coby

Coby TF-DVD7107 Manual

29 August 2024
Coby

Coby TF-DVD1256 Manual

29 August 2024
Coby

Coby TF-DVD7752 Manual

29 August 2024
Coby

Coby TF-DVD7705 Manual

29 August 2024
Coby

Coby TF-DVD5050 Manual

29 August 2024
Coby

Coby TF-DVD7307 Manual

28 August 2024

Bærbar DVD-afspiller Manualer

Nyeste Bærbar DVD-afspiller Manualer

Caliber

Caliber MCM 1102 Manual

14 Oktober 2024
Denver

Denver DFT-2010DVBT Manual

6 Oktober 2024
Reflexion

Reflexion DVD1052N Manual

29 September 2024
Reflexion

Reflexion DVD367 Manual

29 September 2024
AKAI

AKAI APM100 Manual

27 September 2024
Denver

Denver MTW-735TWIN MK2 Manual

27 September 2024
Lenco

Lenco DVP-739X2 Manual

19 September 2024
Caliber

Caliber MHD107 Manual

16 September 2024
Lenco

Lenco DVP-1040 Manual

10 September 2024
AKAI

AKAI APV5608B Manual

8 September 2024