Craftsman CMCB002 Manual

Craftsman Ikke kategoriseret CMCB002

Læs nedenfor 📖 manual på dansk for Craftsman CMCB002 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 23 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

INTRODUCTION

The USB power source is equipped with one USB Type A output port and is designed to charge or supply power to USB

compatible appliances with the use of CRAFTSMAN 20V Max* lithium ion battery packs. Consult the chart at the end of this

manual for compatibility of chargers and batterypacks.

Important Safety Instructions for All Battery Chargers

WARNING: Read all safety warnings, instructions, and cautionary markings for the battery pack, charger

and product. Failure to follow the warnings and instructions may result in electric shock, fire and/or

seriousinjury.

• CRAFTSMANDO NOT attempt to charge the battery pack with any chargers other than a charger.CRAFTSMAN

chargers and battery packs are specifically designed to worktogether.

• These chargers are not intended for any uses other than charging rechargeable batteries. CRAFTSMAN Any other

uses may result in risk of fire, electric shock orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when disconnecting the charger. This will reduce the risk of damage to the

electric plug andcord.

• Make sure that the cord is located so that it will not be stepped on, tripped over or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of

fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide a dry location and use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electricshock.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is, 16 gauge has more capacity than 18gauge. An undersized

cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to

make up the total length, be sure each individual extension contains at least the minimum wire size. The following table

shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier

gauge. The lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

(meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom of thehousing.

• Do not operate the charger with a damaged cord orplug–have them replaced immediately.

• Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take

it to an authorized servicecenter.

• Do not disassemble the charger; take it to an authorized service center when service or repair is required.

Incorrect reassembly may result in a risk of electric shock, electrocution orfire.

• Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard 120V household electrical power. Do not attempt to use it on

any other voltage. This does not apply to the vehicularcharger.

WARNING: Shock hazard. Do not allow any liquid to get inside the charger. Electric shock mayresult.

WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow any liquid to enter the battery pack.

Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return

to a service center for recycling.

CAUTION: Burn hazard. To reduce the risk of injury, charge only rechargeable battery packs. Other types of CRAFTSMAN

batteries may overheat and burst resulting in personal injury and propertydamage.

CAUTION: Under certain conditions, with the charger plugged into the power supply, the charger can be shorted by

foreign material. Foreign materials of a conductive nature, such as, but not limited to, grinding dust, metal chips, steel

wool, aluminum foil or any buildup of metallic particles should be kept away from the charger cavities. Always unplug

the charger from the power supply when there is no battery pack in the cavity. Unplug the charger before attempting

toclean.

Charging a Battery

NOTE: To ensure maximum performance and life of lithium-ion battery packs, charge the battery pack fully before firstuse.

1. Plug the charger into an appropriate outlet before inserting batterypack.

2. Connect the charger and battery pack, making sure the battery is fully seated. The (charging) light will blink

continuously indicating that the charging process hasstarted.

3. The completion of charge will be indicated by the light remaining ON continuously. The battery pack is fully charged

and may be removed and used at this time or left in the charger.

NOTE: To remove the battery pack, some chargers require the battery pack release button to bepressed.

Indicators

Charging

Fully Charged

Hot/Cold Pack Delay

A charger will not charge a faulty battery pack. The charger refusing to light could indicate a problem with the charger.

NOTE: If the charger refuses to light, take the charger and battery pack to be tested at an authorized servicecenter.

Leaving the Battery Pack In the Charger

The charger and battery pack can be left connected with the charge indicator showing pack charged.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures maximum battery packlife.

A cold battery pack may charge at a slower rate than a warm batterypack.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between

65°F – 75°F (18° C– 24°C). DO NOT charge when the battery pack is below +40°F (+4.5°C), or above +104°F (+40°C).

This is important and will prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the touch while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a

warm environment such as in a metal shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other appliance;

b. Check to see if receptacle is connected to a light switch which turns power off when you turn out

the lights;

c. Move the charger and battery pack to a location where the surrounding air temperature is approximately 65°F – 75°F

(18°C – 24°C);

d. If charging problems persist, take the tool, battery pack and charger to your local servicecenter.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a

partially used pack whenever you desire with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but not limited to, grinding dust, metal chips, steel wool, aluminum

foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity. Unplug the charger before attempting toclean.

6. Do not freeze or immerse the charger in water or any otherliquid.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed

from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaningsolutions.

Wall Mounting

These chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 1” (25.4 mm) long, with a screw head diameter of 0.28–0.35” (7–9mm),

screwed into wood to an optimal depth leaving approximately 7/32” (5.5 mm) of the screw exposed. Align the slots on the

back of the charger with the exposed screws and fully engage them in theslots.

Versatrack™

CRAFTSMAN chargers can be mounted to the wall using CRAFTSMAN Versatrack™ Trackwall. Hooks and accessories are sold

separately. Please refer to the Versatrack™ Trackwall accessory sheet for furtherinformation.

USB Power Source

Source d’alimentation USB

Fuente de alimentación USB

CMCB002

INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCTIONES

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

1–888–331–4569 WWW.CRAFTSMAN.COM

READ ALL INSTRUCTIONS

Important Safety Instructions for All Battery Packs

WARNING: Read all safety warnings, instructions, and cautionary markings for the battery pack, charger

and product. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious

injury.

• Do not charge or use the battery pack in explosive atmospheres, such as in the presence of flammable liquids,

gases or dust. Inserting or removing the battery pack from the charger may ignite the dust orfumes.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws,

or other small metal objects, that can make a connection from one terminal to another. Shorting the battery

terminals together may cause burns or a fire.

• NEVER force the battery pack into the charger. modify the battery pack in any way to fit into a non-DO NOT

compatible charger as battery pack may rupture causing serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries andchargers.

• Charge the battery packs only in chargers.CRAFTSMAN

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 104°F

(40°C) (such as outside sheds or metal buildings in summer). For best life store battery packs in a cool, drylocation.

NOTE: Do not store the battery packs in a tool with the trigger switch locked on. Never tape the trigger switch in

the ONposition.

• Do not expose battery pack or tool/appliance to fire or excessive temperature. Exposure to fire or temperature above

265 °F (130 °C) may cause explosion.

• Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when lithium-ion battery packs areburned.

• If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek

medicalattention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark orflame.

WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the battery pack case is cracked or

damaged, do not insert into the charger. Do not crush, drop or damage the battery pack. Do not use a battery pack or

charger that has received a sharp blow, been dropped, run over or damaged in any way (e.g., pierced with a nail, hit

with a hammer, stepped on). Damaged battery packs should be returned to the service center forrecycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place out of the charger for

optimal results.

NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before

use.

Battery Pack Cleaning Instructions

Dirt and grease may be removed from the exterior of the battery using a cloth or soft non-metallic brush. Do not use water

or any cleaningsolutions.

Fuel Gauge Battery Packs

CRAFTSMAN battery packs include a fuel gauge which consists of three LED lights that indicate the level of charge

remaining in the batterypack.

The fuel gauge is an indication of approximate levels of charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge button. A combination of the three LED lights will illuminate

designating the level of charge left. When the level of charge in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate tool functionality and

is subject to variation based on product components, temperature and end-userapplication.

For more information regarding fuel gauge battery packs, please contact CRAFTSMAN at 1-888-331-4569 or visit our

website www.craftsman.com

Transportation

WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects can contact exposed

battery terminals. For example, do not place the battery pack in aprons, pockets, tool boxes, product kit boxes,

drawers, etc., with loose nails, screws, keys, etc. Transporting batteries can possibly cause fires if the battery

terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and

the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting

batteries in commerce or on airplanes in carry-on baggage UNLESS they are properly protected from short circuits.

So when transporting individual battery packs, make sure that the battery terminals are protected and well insulated

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety

instructions below and then follow charging proceduresoutlined. When ordering replacement battery packs, be sure to

include the catalog number andvoltage.

The label on your tool may include the following symbols. The symbols and their definitions are asfollows:

V ......................... volts

Hz hertz .......................

min minutes .....................

or DC direct current ......

...................... Class I Construction (grounded)

…/min .............. per minute

BPM ....................beats per minute

IPM .....................impacts per minute

RPM .................... revolutions per minute

sfpm ................... surface feet per minute

SPM .................... strokes per minute

OPM .................... oscillations per minute

A .........................amperes

W ........................watts

or AC alternating current ...........

or AC/DC alternating or direct current ....

...................... Class II Construction (double insulated)

no .......................no load speed

n ......................... rated speed

...................... earthing terminal

..................... safety alert symbol

..................... visible radiation

..................... avoid staring at light

..................... wear respiratory protection

..................... wear eye protection

..................... wear hearing protection

..................... read all documentation

IPXX .................... IP symbol

USB Power Source Safety Warnings

WARNING: This manual contains important safety and operating instructions for this charging device. Before using the

charging device, read this manual and all labels on the power source, battery pack, charger and product(s) using the

powersource.

• Before using the USB power source, read all instructions and cautionary markings on the USB power source, battery pack

and product using the USB power source.

• Shock hazard. Do not allow any liquid to get inside the USB power source. Electric shock mayresult.

• Burn hazard. To reduce the risk of injury, use only 20V Max* lithium ion battery packs with the USB power source. Do not

attempt to use it on any other battery packs. Other types of batteries may overheat and burst resulting in personal injury and

propertydamage.

• Do not charge appliance during use.

• Do not use a worn USB cable.

• Do not use the USB power source with installed battery pack to charge another battery pack.

• Always use right USB cable. Do not use USB cable with current rating below 1.5 Amps. For fast charging, always use fast

charge cable with current rating higher than 2.0 Amps.

• This USB power source is not intended for any uses other than supplying power/charging small USB electronics.

Any other uses may result in risk of fire, electric shock orelectrocution.

• Do not expose the USB power source to rain orsnow.

• When operating the USB power source outdoors, always provide a dry location.

• Do not operate the USB power source if it has received a sharp blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the USB power source, there are no user serviceableparts.

1 USB Type A output port

2 Belt Clip

3 USB power source

4 Battery pack

Fig. A

Fig. B

from materials that could contact them and cause a short circuit. Li-ion batteries should not be put in NOTE:

checkedbaggage.

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.

DANGER: will Indicates an imminently hazardous situation which, if not avoided, result in death or seriousinjury.

WARNING: could Indicates a potentially hazardous situation which, if not avoided, result in death or seriousinjury.

CAUTION: may Indicates a potentially hazardous situation which, if not avoided, result in minor or moderateinjury.

(Used without word) Indicates a safety related message.

NOTICE: may propertydamage Indicates a practice which, if not avoided, not related to personal injury result in .

The RBRC® Seal

The RBRC® (Rechargeable Battery Recycling Corporation) Seal on the nickel cadmium, nickel metal hydride

or lithium-ion batteries (or battery packs) indicates that the costs to recycle these batteries (or battery

packs) at the end of their useful life have already been paid by CRAFTSMAN. In some areas, it is illegal to

place spent nickel cadmium, nickel metal hydride or lithium-ion batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally consciousalternative.

Call 2 Recycle, Inc., in cooperation with CRAFTSMAN and other battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by returning the spent nickel cadmium, nickel metal hydride or

lithium-ion batteries to an authorized CRAFTSMAN service center or to your local retailer for recycling. You may also contact

your local recycling center for information on where to drop off the spent battery. RBRC® is a registered trademark of Call 2

Recycle,Inc.

USB Charging Ports (Fig. A)

The USB power source 3 is equipped with one USB Type A output port 1 . The USB power source delivers 2amps

Produkt Specifikationer

Mærke:	Craftsman
Kategori:	Ikke kategoriseret
Model:	CMCB002

Har du brug for hjælp?

Hvis du har brug for hjælp til Craftsman CMCB002 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Craftsman Manualer

Craftsman CMXGVAM1144043 Manual

16 September 2024

Craftsman CMHT77621 Manual

14 September 2024

Craftsman CMCED400 Manual

5 September 2024

Craftsman 316.292631 Manual

4 September 2024

Craftsman 98021SE Manual

4 September 2024

Craftsman CMXGZBF71243311 Manual

4 September 2024

Craftsman CMXCAFG190643 Manual

3 September 2024

Craftsman CMCW211 Manual

3 September 2024

Craftsman CMSTC4VT Manual

3 September 2024

Craftsman CMCE600 Manual

24 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer VP-8X8 Manual

25 November 2024

Kramer PT-2C Manual

25 November 2024

Lazer Bob+ Manual

25 November 2024

Dometic DPS 80 Manual

25 November 2024

Kramer 102MX Manual

25 November 2024

Kramer FC-18 Manual

25 November 2024

Kramer DSP-62-UC Manual

25 November 2024

Kramer KC-BRAINware-25 Manual

25 November 2024

Kramer KC-BRAINware-50 Manual

25 November 2024

Tiger SKF-H101 Manual

25 November 2024