Crestron DIN-1DIM4 Manual


Læs nedenfor 📖 manual på dansk for Crestron DIN-1DIM4 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
DIN-1DIM4
DIN Rail 4-Channel Dimmer
Operations & Installation Guide
Description
The Crestron® DIN-1DIM4 is a DIN rail mounted lighting control module with four channels
of dimming. A single model supports both 120 and 220-277 V electronic and magnetic
low-voltage, incandescent, neon/cold cathode, 2-wire dimmable uorescent, and
non-dimmable lighting loads up to 5 A per channel, 10 A total.
Additional Resources
Visit the product page on the Crestron website (www.crestron.com) or
scan the QR code to the right for additional information and the latest
rmware updates.
Hardware Hookup
Make the necessary connections as shown below. Apply power after all connections have
been made. When making connections to the DIN-1DIM4, use Crestron power supplies for
Crestron equipment.
WARNING: Prior to connecting the device, turn off power at the circuit breaker. Failure to
do so may result in serious personal injury or damage to the device. Restore power after
all connections have been made.
CAUTION: Connecting this device to the wrong type of load or short circuiting the load
can cause severe product damage. Each load should be tested to identify a short circuit
condition prior to wiring the load to the module.
NOTE: Strip the ends of the wires approximately 1/4 in (6 mm). Use care to avoid nicking
the conductors. Twist together the ends of the wires that share a connection. Apply solder
only to the ends of the twisted wires. Avoid tinning too far up the wires or the end
becomes brittle.
NOTE: High-voltage connections accept 2.5 mm
2 (12 AWG) wire. Wire should be stripped
to 8 mm (1/3 inch). Tighten terminal blocks to 0.5 Nm (5 in-lbs).
NOTE: The DIN-1DIM4 power feed must be protected by a 10 A (trip curve C) breaker or
equivalent.
NOTE: The DIN-1DIM4 outputs must be used to control permanently installed lighting
loads only.
NOTE: Do not mix magnetic and electronic transformers on the same dimmer output.
NOTE: Use copper wire only. For high-voltage connections, use wire rated for at least
75º C (167º F).
NOTE: Ensure the unit is properly grounded by connecting the chassis ground lug to an
earth ground (building steel).
Hardware Connections for the DIN-1DIM4
Installation
WARNING: To avoid re, shock, or death, turn off power at circuit breaker or fuse and
test that power is off before wiring!
CAUTION: This equipment is for indoor use only. Mount in a well-ventilated area. The
ambient temperature must be 0º to 40º C (32º to 104º F). The relative humidity must be
10% to 90% (non-condensing).
NOTE: This product should be installed and used in accordance with appropriate
electrical codes and regulations.
NOTE: This product should be installed by a qualied electrician.
NOTE: When installing in an enclosure, high-voltage devices should be grouped
separately from low-voltage devices.
Install the DIN-1DIM4
The DIN-1DIM4 installs on a DIN rail.
1. Use a at object (e.g., a at-head screwdriver) to pull the DIN rail release downward.
2. With the top of the unit tilted down, place the DIN-1DIM4 against the bottom of the
DIN rail.
NOTE: When mounting DIN rail products, it may be necessary to use a at-head
screwdriver to pull the DIN rail release tab down while snapping the device onto
the DIN rail.
3. Tilt the top of the DIN-1DIM4 toward the DIN rail until it is secure on the top edge of
the rail. Push the DIN rail release upward to lock the DIN-1DIM4 into place.
Mount DIN-1DIM4
Remove the DIN-1DIM4
To remove the DIN-1DIM4 from the DIN rail, use a at object (e.g., a at-head screwdriver)
to pull the DIN rail release and tilt the bottom of the DIN-1DIM4 away from the DIN rail.
NOTE: Certain third party DIN cabinets provide space for an informational label
between each DIN rail row. Crestron’s Engraver software (version 4.0 or later) can
generate appropriate labels for all Crestron DIN rail products.
Top
DIN Rail
(Not Supplied)
DIN Rail
Release
Neutral
Line
120/277 Volts
from Breaker
120/277 Volts
Load
Ground
Neutral
Line
Ground
NET:
To Control System
and Other
Cresnet® Devices
LIVE:
Line Power Input
from AC Power Line
OVERRIDE:
From Device
Providing Override
Signal and to Other
Devices Receiving
Override Signal
NEUTRAL:
Neutral
Connection from
AC Power LIne
DIMMED LIVE (1 - 4):
Dimmer Channel
Outputs
Ground
With the circuit breaker turned off, connect the wires to the terminal blocks per the
markings provided on the DIN-1DIM4.
Load Connections Example for the DIN-1DIM4
Set the Net ID
The Net ID of the DIN-1DIM4 has been factory set to 89. The Net IDs of all devices in the
same system must be unique. The Net ID can be changed from the front panel of the
DIN-1DIM4 or from a personal computer via Crestron Toolbox™.
Set the Net ID using the front panel.
1. Press the button to enter Setup mode. The SETUP LED illuminates.SETUP
2. Press the left and right button under the NET ID display to change the Net ID.
NOTE: The DIN-1DIM4 will leave Setup mode after 10 seconds of inactivity and
revert to the previously set Net ID.
3. When the desired Net ID is displayed, press the button to exit Setup mode. SETUP
The SETUP LED extinguishes.
NOTE: If an invalid Net ID is set (i.e., 00, 02, FF), “Er” will be displayed on the NET
ID display and the DIN-1DIM4 will revert to the previously set Net ID.
A small Net ID label is provided on the DIN-1DIM4 to document the unit’s Net ID in the case
where power is not available. Apply a mark over the digits that correspond to the assigned
Net ID.
NET ID Label (“3C” Shown)
Establish Override Mode Levels
Override mode disables the control system program and sets all of the output states to the
stored override values. The state of each output can be saved as an override setting,
which can be automatically recalled when Override mode is enabled.
NOTE: The control system program has a setting that can prevent locally saving the
override state. If this setting is enabled, the display shows “Er” when trying to save
override states. For more information, refer to the SIMPL Windows help le.
To save the load level as an override setting, set all of the loads to their desired levels and
then press and hold the button for three seconds. The OVR LED blinks to indicate the OVR
new override setting has been stored.
Toggle Override Mode
To enable Override mode, press the button. The OVR LED ashes slowly. Override OVR
mode can also be toggled via a remote contact closure attached to the OVERRIDE port.
NOTE: If Override mode was enabled from an external device (i.e., a contact closure
connected to the OVERRIDE port), the OVR LED will ash quickly when the local OVR
button is pressed. Pressing the local button has no effect when Override mode was OVR
toggled via the remote connection.
To disable Override mode, press the button again. The OVR LED extinguishes and OVR
the outputs return to the states set by the control system program.
NOTE: If override levels have not been saved, the factory default override level is 100%.
Reboot the DIN-1DIM4
To reboot the DIN-1DIM4, press the button. The outputs will be set to the states RESET
currently specied by the control system program. If the control system does not provide
any values, the outputs will be set to the previously set values.
Select the Operating Mode
CAUTION: Selecting an incompatible lighting load may cause damage to the
DIN-1DIM4 or the lighting load.
In the event that the DIN-1DIM4 is to be operated without a connection to a control
system, the operating mode must be set locally.
NOTE: Once a program has been downloaded to the DIN-1DIM4, the manual selection
of load types will be restricted. For example, if the program denes a channel as
NON-DIM, it cannot be set to DIM locally. Similarly, if the program denes a channel as
DIM, it cannot be set to NON-DIM locally.
Once a connection to a control system has been established, the SIMPL windows symbol
should dene the unit as DIM or NON-DIM. The operating mode must still be selected
locally on the dimmer.
The operating mode is selected locally for each channel using the recessed channel mode
select buttons. Press the recessed button for the appropriate channel until the proper
operating mode is selected. Repeat this process for each channel on the dimmer. Refer to
the table that follows for information about each operating mode and the corresponding
unit display.
Operation
NOTE: Before using the DIN-1DIM4, ensure the device is using the latest rmware.
Check for the latest rmware for the DIN-1DIM4 at www.crestron.com/rmware. Firmware
is loaded onto the device using Crestron Toolbox.
The DIN-1DIM4 can be controlled via its front panel as well as from a control system. The
following local controls are available.
Control the Loads from the Front Panel
The lighting level of each output can be manually controlled from the front panel.
To toggle the light between off and 100% (on), tap the appropriate load button. The
corresponding LED illuminates and the output level is shown on the NET ID display (“oF” for
off, “On” for on) for two seconds after the button is released.
To ramp the lighting level up or down (until it reaches a limit), press and hold the
appropriate load button. To change the ramp direction, release the load button, and then
press and hold it again. The corresponding LED illuminates and the output level is shown on
the NET ID display as a percentage (01% to 99%) for two seconds after the button is
released.
NOTE: The control system program may change the settings if Override mode is not
enabled.
OPERATING MODE UNIT DISPLAY
DIM: Channel operates as a dimmer with no
switching capabilities. The DIM LED will illuminate
when operating as a dimmer.
Operating mode should be set to DIM when
controlling dimmable xtures.
NON-DIM: Channel operates only as a switch with
no dimming capabilities. The NON-DIM LED will
illuminate when operating as a switch.
Operating mode should be set to NON-DIM when
controlling non-dimmable xtures.


Produkt Specifikationer

Mærke: Crestron
Kategori: Ikke kategoriseret
Model: DIN-1DIM4

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron DIN-1DIM4 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Crestron Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024