CyberPower CST150UC-FC Manual

CyberPower Ikke kategoriseret CST150UC-FC

Læs nedenfor 📖 manual på dansk for CyberPower CST150UC-FC (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

YOUR ULTIMATE ALLY IN POWER

CST150UC-FC

USER MANUAL

Cyber Power Systems (USA), Inc. 4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 | CyberPowerSystems.com

IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS)

When using electrical appliances, basic safety precautions should always be followed to

reduce the risk of fire, electric shock, and/or injury to persons including the following. This

Manual Contains Important Instructions that should be followed during installation and

maintenance of the UPS and batteries.

CAUTION! To prevent the risk of fire or

electric shock, install in a temperature

and humidity controlled indoor area free

of conductive contaminants. (Please see

specifications for acceptable temperature

and humidity range).

CAUTION! To reduce the risk of electric

shock, do not remove the cover except to

service the battery. Turn off and unplug the

unit before servicing the batteries. There

are no user serviceable parts inside except

for the battery.

CAUTION! Hazardous live parts inside can

be energized by the battery even when the

AC input power is disconnected.

CAUTION! The UPS must be connected

to an AC power outlet with fuse or circuit

breaker protection. Do not plug into an

outlet that is not grounded. If you need to

de-energize this equipment, turn off and

unplug the unit.

CAUTION! To avoid electric shock, turn off

the unit and unplug it from the AC power

source before servicing the battery.

CAUTION! Not for use in a computer

room as defined in the Standard for the

Protection of Electronic Computer/Data

Processing Equipment, ANSI/NFPA 75.

CAUTION! To reduce the risk of fire,

connect only to a circuit provided with

20 amperes maximum branch circuit over

current protection in accordance with the

National Electric Code, ANSI/NFPA 70.

DO NOT USE FOR MEDICAL OR LIFE

SUPPORT EQUIPMENT! CyberPower

Systems does not sell products for life

support or medical applications. DO NOT

use in any circumstance that would affect

the operation and safety of life support

equipment, medical applications, or patient

care.

DO NOT USE WITH OR NEAR

AQUARIUMS! To reduce the risk of fire

or electric shock, do not use with or near

an aquarium. Condensation from the

aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY

TRANSPORTATION! To reduce the risk of

fire or electric shock, do not use the unit

on any transportation such as airplanes

or ships. The effect of shock or vibration

caused during transit and the damp

environment can cause the unit to short

out.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt.

The box should contain the following:

(a) UPS

(b) User’s manual

(d) Function Setup Guide

*PowerPanel® Personal software is

available on our website. Please visit

cyberpowersystems.com and go to the

Software Section for free download.

OVERVIEW

The /CST150UC-FC provides complete

power protection from utility power that

is not always consistent. The /CST150UC-

FC features 1500 Joules of surge

protection. The unit provides long lasting

battery backup during power outages

with maintenance free batteries. The /

CST150UC-FC ensures consistent power

to your computer system and includes

software that will automatically save your

open files and shutdown your computer

system during a utility power loss.

AUTOMATIC VOLTAGE REGULATOR

The /CST150UC-FC stabilizes inconsistent

utility power voltage to nominal levels

that are safe for equipment. Inconsistent

incoming utility power may be damaging

to important data files and hardware, but

with Automatic Voltage Regulation (AVR),

damaging voltage levels are corrected to

safe levels. AVR automatically increases

low utility power to a consistent and safe

110/120 volts.

DETERMINE THE POWER REQUIREMENTS

OF YOUR EQUIPMENT

1 . Ensure that the equipment plugged

into the outlet does not exceed the

UPS’s rated capacity (1350VA/810W

for , 1500VA/900W for CST150UC-

FC). If the rated capacity of the unit is

exceeded, an overload condition may

occur and cause the UPS to shut down

or the circuit breaker to trip.

2. There are many factors that can affect

the amount of power that your

computer system will require. It is

suggested that the load placed on the

battery outlets not exceed 80% of the

unit’s capacity.

REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly. Most retailers that sell lead-acid batteries collect used batteries for recycling, as required by

local regulations.

K01-0000931-01

1 . Power Switch: Used as the master on/

off switch for equipment connected

to the battery power supplied outlets.

(Please refer to the Function Setup

Guide for more information.)

2 . Power On Indicator: This LED is

illuminated when the utility power

is normal and the UPS outlets are

providing power, free of surges and

spikes.

3 . LCD module display: The LCD display

shows all the UPS information

using icons and messages. For

more information please review the

“Definitions for Illuminated LCD

Indicators” section below.

4 . Display/Select Button: The button

can be used to select the LCD display

contents including Input Voltage,

Output Voltage, and Estimated Run

Time. Short press the button to scroll

down the function menu. Pressing

the button for 3 seconds will keep the

LCD display always on or turn the LCD

display off while in AC/Utility power

mode. For more information, please

refer the Function Setup Guide.

5 . USB Charging Ports: USB Charging

ports provide 5Vdc,3A Max(USB-C),

and 5 Vdc, 2.4A Max(USB-A). Total

Output Current:4A CST150UC-FC USB

Charging ports provide 5Vdc,2.5A

Max/ 9Vdc,2A Max (USB-C), and 5

Vdc, 2.4A Max (USB-A). Total Output

Current:30W

6 . Battery and Surge Protected

Outlets: The UPS has five battery

powered/surge suppression outlets

for connected equipment to ensure

temporary uninterrupted operation

of your equipment during a power

failure. (DO NOT plug a laser printer,

paper shredder, copier, space heater,

vacuum, sump pump or other large

electrical devices into the “Battery

and Surge Protected Outlets”. The

power demands of these devices may

overload and damage the unit.)

7 . Full-Time Surge Protection Outlets:

The UPS has five surge suppression

outlets.

8 . Circuit Breaker: Located on the back of

the UPS, the circuit breaker serves to

provide overload and fault protection.

9 . USB Ports to PC: Use the type B to type

A USB cable to connect the product to

a computer.

10 . Communication Protection Ports:

Communication protection ports,

bi-directional, will protect a

10/100/1000 Ethernet connection

(RJ45).

11 . Coax/Cable/DSS Surge Protection:

The Coax/Cable/DSS protection ports

will protect any cable modem, CATV

converter, or DSS receiver.

12 . Wiring Fault Indicator (red): This LED

indicator will illuminate to warn the

user that a wiring problem exists, such

as bad ground, missing ground or

reversed wiring. If this is illuminated,

disconnect all electrical equipment

from the outlet and have an electrician

verify the outlet is properly wired. The

UPS will not provide surge protection

without being plugged into a grounded

and properly wired wall outlet.

13 . Widely Spaced Outlets Designed for

AC Adapters: The unit has two outlets

spaced to allow AC power adapter

blocks to be plugged into the UPS

without blocking adjacent outlets.

BASIC OPERATION

HARDWARE INSTALLATION GUIDE

1 . Your new UPS may be used

immediately upon receipt. However,

after receiving a new UPS, to ensure

the battery’s maximum charge capacity,

it is recommended that you charge the

battery for at least 8 hours. Your UPS is

equipped with an auto-charge feature.

When the UPS is plugged into an AC

outlet, the battery will automatically

charge whether the UPS is turned on or

off.

Note: This UPS is designed with a

safety feature to keep the system from

being turned on during shipment. The

first time you turn the UPS on, you will

need to have it connected to AC power

or it will not power up.

2 . With the UPS

unit turned off

and unplugged,

connect your

computer, monitor,

and any other peripherals requiring

battery backup into the battery power

supplied outlets. DO NOT plug a

laser printer, paper shredder, copier,

space heater, vacuum, sump pump

or other large electrical devices into

the “Battery and Surge Protected

Outlets”. The power demands of these

devices may overload and damage the

UPS.

3 . Plug the UPS into a 2 pole, 3 wire

grounded receptacle (wall outlet).

Make sure the wall branch outlet is

protected by a fuse or circuit breaker

and does not service equipment

with large electrical demands (e.g.

air conditioner, copier, etc…). The

warranty prohibits the use of extension

cords, outlet strips, and surge strips.

4 . Press the power switch to turn the unit

on. The Power On indicator light will

illuminate and the unit will “beep”. If an

overload is detected, an audible alarm

will sound and the unit will emit one

long beep. To correct this, turn the

UPS off and unplug at least one piece

of equipment from the battery power

supplied outlets. Make sure the circuit

breaker is depressed and then turn the

UPS on.

5 . To maintain optimal battery charge,

leave the UPS plugged into an AC

outlet at all times.

6 . To store the UPS for an extended

period, cover it and store with the

battery fully charged. While in storage,

recharge the battery every three

months to ensure battery life.

7 . Ensure the wall outlet and UPS are

located near the equipment being

attached for proper accessibility.

INSTALLING YOUR UPS SYSTEM - Continued

PLUG IN

PRODUCT REGISTRATION

Thank you for purchasing a CyberPower product. Please take a few minutes to register your product at: cyberpowersystems.com/registration. Registration certifies your product's warranty,

confirms your ownership in the event of a product loss or theft and entitles you to free technical support. Register your product now to receive the benefits of CyberPower ownership.

FEATURES

1 . Power Switch

2 . Power On Indicator

3 . LCD module display

4 . Display/Select Button

5 . USB Charging Ports

6 . Battery and Surge Protected Outlets

7 . Full-Time Surge Protection Outlets

8 . Circuit Breaker

9 . USB Ports to PC

10 . Communication Protection Ports

1 1 . Coax/Cable/DSS Surge Protection

12 . Wiring Fault Indicator (red)

13 . Widely Spaced Outlets Designed for AC Adapters

13 13

Replacement of batteries located in an OPERATOR ACCESS AREA.

1 . When replacing batteries, replace with the same number of the following battery:

CyberPower / RB1270X2C for the and CyberPower / RB1290X2 for the CST150UC-FC.

2 . CAUTION! Risk of Energy Hazard, 24 V, maximum 9 Ampere-hour battery. Before

replacing batteries, remove conductive jewelry such as chains, wrist watches, and

rings. High energy conducted through these materials could cause severe burns.

3 . CAUTION! Do not dispose of batteries in a fire. The batteries may explode.

4 . CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin

and eyes. It may be toxic.

5 . CAUTION: A battery can present a risk of electrical shock and high short circuit

current. The following precautions should be observed when working on batteries:

1) Remove watches rings, or other metal objects.

2) Use tools with insulated handles.

CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATIONS.

REPLACING THE BATTERY BATTERY REPLACEMENT PROCEDURE:

1 . Switch off and unplug all the connected equipment.

2 . Switch off the UPS and disconnect it from the wall outlet.

3 . Place the product on its side, on a solid and stable surface.

4 . Loosen the battery compartment cover screws.

5 . Press on the locking latch and slide the battery compartment cover.

6 . Disconnect the battery wires from the right side of the battery and then take it out of

the battery compartment.

7 . Disconnect the battery wires from the remaining battery.

8 . Slide the remaining battery from left to right and remove it from the compartment.

9 . Install the "left side" replacement battery by connecting the yellow wire (+) to the red

connector from the battery and the black wire (-) to the black connector from the

battery. Place the battery into the left side of the compartment.

10 . Install the "right side" replacement battery by connecting the red wire (+) to the

red connector from the battery and yellow wire (-) to the black connector from the

battery. Place the battery into the right side of the compartment. Note: Only new

batteries should be used for replacement and both batteries should be replaced at

the same time to ensure maximum life span.

1 1 . Close the battery compartment cover and secure it with the screws.

1 2 . Recharge the UPS for 8-16 hours to fully charge the battery.

1 2 3 4 5

6 7 8

(+)Red

(-)Black (-)Black

(+)Red

Yellow Wire to (+) Red Connector

Black Wire to (-) Black Connector

Red Wire to (+) Red Connector

Yellow Wire to (-) Black Connector

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Ikke kategoriseret
Model:	CST150UC-FC

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberPower CST150UC-FC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret CyberPower Manualer

CyberPower CPS3500PIE Manual

8 November 2024

CyberPower CPS5000PIE Manual

8 November 2024

CyberPower BPS240V9A Manual

7 November 2024

CyberPower Essential B704 Manual

10 Oktober 2024

CyberPower Rackbar RKBS20ST6F8R Manual

7 Oktober 2024

CyberPower RMCARD305 Manual

4 Oktober 2024

CyberPower Professional CSP708T Manual

4 Oktober 2024

CyberPower SB0602BA-DE-B50 Manual

24 September 2024

CyberPower SB0802AD-DE-W24 Manual

24 September 2024

CyberPower SB0502BA-DE-B70 Manual

24 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron Overbridge Manual

26 November 2024

Elektron Sidstation Manual

26 November 2024

SKROSS World Adapter Pro+ Manual

26 November 2024

SKROSS PRO – World & USB Manual

26 November 2024

SoundTube IPD-RS82-EZ Manual

26 November 2024

Kramer 4x1VB Manual

26 November 2024

Kramer RC-63A Manual

26 November 2024

SoundTube IPD-HP82-EZ Manual

26 November 2024

Kramer RK-KVM-1U-PP3 Manual

26 November 2024

Gioteck VX-2 (PS3) Manual

26 November 2024