CyberPower P504UC Manual

CyberPower Ikke kategoriseret P504UC

Læs nedenfor 📖 manual på dansk for CyberPower P504UC (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

YOUR ULTIMATE ALLY IN POWER

5-OUTLET

SURGE PROTECTOR

(5 AC OUTLETS & 2 USB PORTS)

P504UC

USER MANUAL

FEATURES

1. ON/OFF Reset Control Switch and Circuit Breaker

Controls power to all outlets. The switch is also a 15 A

breaker. When an overload occurs, it will automatically

switch o. To resume operation, ensure the overload

condition is removed and reset the surge protector by

switching the unit ON.

2. USB-A Charging Port (1)

3. USB-C Charging Port (1)

4. Standard Grounded Outlets (5)

SPECIFICATIONS

Model Number: P504UC

Outlets: Standard Grounded Outlets (5),

USB Charging Ports (2)

Surge Protection: 500 Joules

USB-A Charging Output: 5 V/2.4 A

USB-C Charging Output: 15 W

USB Output Total: 15 W

Electrical Rating: 125 V/15 A/1875 W

UL Clamping Voltage: UL 1449 4th/800 V (L-N)

Maximum Peak Current: 15,000 A

1 AC Line Protected: L-N: 15,000 A

Response Time: Less than 1 nanosecond

Plug Type: Flat

Cord Length: 4 ft

i WARNING: This product can expose you to chemicals including bisphenol A (BPA)

and styrene, which is known to the State of California to cause reproductive harm and

cancer. For more information, go to www.P65Warnings.ca.gov.

3 CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK:

Use only in dry locations and only indoors.

DO NOT plug into another relocatable power tap.

DO NOT “daisy chain” surge protectors.

DO NOT use with any aquarium equipment.

DO NOT use if properly grounded outlets are not available.

DO NOT install this device if there is less than 10 meters (30 feet) or more of wire

between the electrical outlet and electrical service panel.

DO NOT use for medical or life support equipment. This device features an internal

protection that will disconnect the surge protective component at the end of its

useful life, but it will maintain unprotected power to the load.

TROUBLESHOOTING

If the ON/OFF is switched OFF, the 15 Amp circuit breaker may have tripped.

Examine your connected equipment and remove the device that is overloading

the circuit. Then, turn the ON/OFF switch back to RESET.

FOR MORE INFORMATION TECHNICAL SUPPORT

Visit CyberPowerSystems.com for more information regarding: Visit: CyberPowerSystems.com/support

• Product information and certiﬁcations Toll-Free: 1-877-297-6937

• Product warranty Hours of Operation: Monday - Friday: 7:00am - 6:00pm CST

All other trademarks are the property of their respective owners.

CONFORMANCE APPROVALS harmful interference in a residential installation. This equipment • Reorient or relocate the receiving antenna.

This device complies with Part 15 of the FCC Rules. generates, uses, and can radiate radio frequency energy and, if not • Increase the separation between the equipment and receiver.

Operation is subject to the following two conditions: (1) this installed and used in accordance with the instructions, may cause • Connect the equipment into an outlet on a circuit dierent from

device may not cause harmful interference, and (2) this device must harmful interference to radio communications. that to which the receiver is connected.

accept any interference received, including interference that may However, there is no guarantee that interference will not occur • Consult the dealer or an experienced radio/TV technician for help.

Cyber Power Systems (USA), Inc. cause undesired operation. in a particular installation. If this equipment does cause harmful

This equipment has been tested and found to comply with the limits interference to radio or television reception, which can be determined WARNING: Changes or modiﬁcations not expressly approved by the

4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 for a Class B digital device, pursuant to Part 15 of the FCC Rules. by turning the equipment on and o, the user is encouraged to try to party responsible for compliance could void the user’s authority to

These limits are designed to provide reasonable protection against correct the interference by one or more of the following measures: operate the equipment.

CyberPowerSystems.com

K01-E000020-00