CyberPower PR3000LCDSL Manual

CyberPower Ikke kategoriseret PR3000LCDSL

Læs nedenfor 📖 manual på dansk for CyberPower PR3000LCDSL (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

PR2200LCDSL / PR3000LCDSL

User’s Manual

K01-0000287-01

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions that must be followed during installation and maintenance of the UPS and batteries. Please read and

follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or

operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive

contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. Turn off and unplug the unit before

servicing the batteries. There are no user serviceable parts inside except for the battery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not

grounded. If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer

component.

CAUTION! Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment,

ANSI/NFPA 75.

CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 (PR2200LCDSL) or 30 (PR3000LCDSL) amperes maximum

branch circuit over current protection in accordance with the National Electric Code, ANSI/NFPA 70.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical

applications. use in any circumstance that would affect the operation and safety of life support equipment, medical applications, or DO NOT

patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium. Condensation

from the aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of fire or electric shock, do not use the unit on any transportation

such as airplanes or ships. The effect of shock or vibration caused during transit and the damp environment can cause the unit to short out.

INTRODUCTION

Thank you for selecting a CyberPower Systems UPS product. This UPS is designed to provide unsurpassed power protection, operation and

performance during the lifetime of the product.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit (b) User’s manual (c) Function Setup Guide (d) Emergency Power Off cable (gray) (e) Serial cable (f) USB A+B type cable

*PowerPanel® Personal Edition software is available on our website.

Please visit www.cyberpower.com and go to the Software Section for free download.

OVERVIEW

The PR2200LCDSL/PR3000LCDSL provides complete power protection from utility power that is not

always consistent. The PR2200LCDSL/PR3000LCDSLfeatures surge protection against power surges

and maintenance free batteries for long lasting battery backup during power outages. In addition to

ensuring consistent power to your computer system and the PR2200LCDSL/PR3000LCDSL also

includes software that will automatically save your open files and shutdown your computer system during

a utility power loss.

AUTOMATIC VOLTAGE REGULATOR

The PR2200LCDSL/PR3000LCDSL stabilizes inconsistent utility power voltage to nominal levels that are

safe for equipment. Inconsistent utility power may be damaging to important data files and hardware, but

with Automatic Voltage Regulation (AVR), damaging voltage levels are corrected to safe levels. AVR automatically increases low utility power

and decreases high utility power to a consistent and safe 110/120 volts.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the outlets does not exceed the UPS unit’s rated capacity (2070VA/1980W for PR2200LCDSL,

3000VA/2700W for PR3000LCDSL). If the rated capacities of the unit are exceeded, an overload condition may occur and cause the UPS

unit to shut down or the circuit breaker to trip.

2. There are many factors that can affect the amount of power that your computer system will require. It is suggested that the load placed on the

battery outlets not exceed 80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immedi ately upon receipt. However, to ensure the battery’s maximum

charge capacity, it is recommended that you charge the battery for at least 8 hours. Your UPS is

equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the battery will

automatically charge whether the UPS is turned on or off.

Note: This UPS is designed with a safety feature to keep the system from being turned on during

shipment.

The first time you turn the UPS on, you will need to have it connected to AC power or it will

not power up.

2. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other peripherals requiring battery backup into the

battery power supplied outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or other large

electrical devices into the “Battery and Surge Protected Outlets”. The power demands of these devices may overload and damage

the unit.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air

conditioner, copier, etc…). The warranty prohibits the use of extension cords, outlet strips, and surge strips.

4. Press the power switch to turn the unit on. The Power On indicator light will illuminate and the unit will “beep”.

If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at

least one piece of equipment from the battery power supplied outlets. Make sure the circuit breaker is depressed and then turn the UPS on.

5. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

6. To store the UPS for an extended period, cover it and store with the battery fully charged. While in storage, recharge the battery every three

months to ensure battery life.

7. Ensure the wall outlet and UPS are located near the equipment being attached for proper accessibility.

DESCRIPTION

Front Panel

1 Power Switch

Used as the master on/off switch for equipment connected to the battery power

supplied outlets.

2 Power On Indicator

This LED is illuminated when the utility power is normal and the UPS outlets are

providing power, free of surges and spikes.

3 LCD Module Display

The intelligent LCD display shows all the UPS information using icons and messages.

For more information please review the “Definitions for Illuminated LCD Indicators”

section below.

4 Down/Display Button

The button can be used to select the LCD display contents including Input Voltage,

Output Voltage, and Estimated Run Time. Short press the button to scroll down the function menu. Pressing the button for 2 seconds will

keep the LCD display always on or turn the LCD display off while in AC/Utility power mode. For more information, please refer to the

Function Setup Guide.

5 Up/Mute Button

Short press the button to scroll up the function menu. Holding the button for more than 2 seconds will silence the alarm. For more

information, please refer to the Function Setup Guide.

6 Enter/Setup Button

Press the button for 2 seconds to enter the setup menu and then select the functions for configuration. For mor e information, please refer to

the Function Setup Guide.

Rear Panel

1 Battery and Surge Protected Outlets

The unit has seven battery powered/surge

suppression outlets for connected equipment to

ensure temporary uninterrupted operation of your

equipment during a power failure.

(DO NOT plug a laser printer, paper shredder,

copier, space heater, vacuum, sump pump or

other large electrical devices into the “Battery

and Surge Protected Outlets”. The power

demands of these devices may overload and

damage the unit.)

2 Serial/USB Ports to PC

The Serial and USB ports allow connection and

communication between the computer and the

UPS unit. Note: Only one port can be used at a

time.

3 EPO Port

Use the provided gray EPO cable to connect to a provided EPO contact

switch. Follow the appropriate circuit diagram to the right to wire the cable

to your EPO configuration. The EPO remote switch is a switch installed in

an outside area, connected to the unit via the Emergency Power Off cable.

In case of an emergency, it can be used to immediately cut-off power from

the UPS.

4 TVSS Ground

The TVSS GND only is used for dielectric voltage-withstand testing during

production.

5 SNMP/HTTP Network Slot

Remove the cover panel to install an optional RMCARD to remotely monitor and manage your UPS over a network.

6 Wiring Fault Indicator (red)

This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or reversed wiring. If this

is illuminated, disconnect all electrical equipment from the outlet and have an electrician verify the outlet is properly wired. The UPS will

operate normally and provide battery backup even if the indicator illuminates. However, the unit will not provide surge protection without

being plugged into a grounded and properly wired outlet.

7 AC Input Power Cord

Heavy-duty power cord.

8 Circuit Breaker

Located on the back of the UPS, the circuit breaker provides overload and fault protection.

REPLACING THE BATTERY

Replacement of batteries located in an OPERATOR ACCESS AREA.

When replacing batteries, replace with the same number of the following battery: CyberPower / RB1290X4K for the PR2200LCDSL and the

PR3000LCDSL. Contact CyberPower Systems about replacement batteries.

CAUTION! Risk of Energy Hazard, 12V, maximum 9 Ampere-hour batteries. Before replacing batteries, remove conductive jewelry such as

chains, wrist watches, and rings. High energy conducted through these materials could cause severe burns.

CAUTION! Do not dispose of batteries in a fire. The batteries may explode.

CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be toxic.

CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING

TO LOCAL REGULATIONS.

BATTERY REPLACEMENT PROCEDURE:

1. Turn off and unplug all connected equipment.

2. Turn the UPS off and unplug it from the AC power source.

3. Remove the front panel of the UPS.

4. Remove screws from the battery compartment cover and slide the cover completely off of the unit.

5. Remove the batteries from the compartment.

6. Disconnect the battery wires from the batteries.

7. Install the replacement batteries by connecting the red wire (+) and black wire (-) to the same color connectors from the battery pack.

8. Put the batteries back into the compartment.

9. Re-install the battery compartment cover and tighten the retaining screws.

10. Put the front panel back on the UPS.

11. Connect to AC power and charge the new batteries for up to 16 hours to insure a full charge.

PR2200LCDSL / PR3000LCDSL

REMINDER: Batteries are considered and must be disposed of properly. Most retailers that sell lead-acid batteries HAZARDOUS WASTE

collect used batteries for recycling, as required by local regulations.

1. ONLINE: The UPS is supplying utility power to connected equipment.

2. BATTERY: During a severe brownout or blackout, this icon appears and an alarm sounds

(two short beeps followed by a pause) to indicate the UPS is operating from its internal

batteries. During a prolonged brownout or blackout, the alarm will beep rapidly every 1/2

second (and the BATT.CAPACITY meter shows one 20% capacity segment shaded. The

capacity depends on how much load added and the runtime left.) to indicate the UPS’s

batteries are nearly out of power. You should save files and turn off your equipment

immediately or allow the software to shut the system down.

3. Energy-Saving: The UPS in energy-saving bypass mode. When the utility power is

normal and the battery is fully charged, the UPS will go into energy-saving bypass mode

automatically. See “CyberPower GreenPower UPS

TM Technology” section for more

information.

4. LOAD capacity / Sensitivity setup: This meter displays the approximate output load level (in 20% increments) of the UPS battery outlets. It

can also be sensitivity setup meter if you are in Setup mode. It is to control the sensitivity of the UPS to switch to Battery Mode by selecting

UPS shutdown voltage range. When the sensitivity is increased, the UPS will switch to Battery Mode with less input power variation.

5. BATTERY capacity: This meter displays the approximate charge level (in 20% increments) of the UPS’s internal battery. During a blackout

or severe brownout, the UPS switches to battery power, the BATTERY icon appears, and the charge level decreases.

6. FAULT: This icon appears if there is a problem with the UPS. Press the POWER button to turn off the UPS.

F01: Battery Mode or AC/Utility Power Mode Overload fault (Turn on the UPS again.)

F02: Battery Output Short fault (Turn on the UPS again.)

F03: Charger Fault (Contact CyberPower Systems for support.)

F04: Internal Fault (Contact CyberPower Systems for support.)

F05: Fan Abnormal (Contact CyberPower Systems for support.)

7. OVER LOAD: This icon appears and an alarm sounds to indicate the battery-supplied outlets are overloaded. To clear the overload, unplug

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY INSTRUCTIONS

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

PR2200LCDSL PR3000LCDSL

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Ikke kategoriseret
Model:	PR3000LCDSL

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberPower PR3000LCDSL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret CyberPower Manualer

CyberPower SNEV001 Manual

24 December 2024

CyberPower P406U Manual

3 December 2024

CyberPower BP192VL2U01 Manual

2 December 2024

CyberPower CPS3500PIE Manual

8 November 2024

CyberPower CPS5000PIE Manual

8 November 2024

CyberPower BPS240V9A Manual

7 November 2024

CyberPower Essential B704 Manual

10 Oktober 2024

CyberPower Rackbar RKBS20ST6F8R Manual

7 Oktober 2024

CyberPower RMCARD305 Manual

4 Oktober 2024

CyberPower Professional CSP708T Manual

4 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

25 December 2024

25 December 2024

25 December 2024

25 December 2024

25 December 2024

Philips SWF2620 Manual

25 December 2024

Philips 13BDL4150IW Manual

25 December 2024

Vivax TS-950B Vintage Manual

24 December 2024

Lucide Lorenz 74403/06/97 Manual

24 December 2024

Lucide Jur 72405/57/30 Manual

24 December 2024