CyberPower RT650EI Manual

CyberPower UPS RT650EI

Læs nedenfor 📖 manual på dansk for CyberPower RT650EI (2 sider) i kategorien UPS. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

RT650EI / RT500EI

User’s Manual

K01-0000540

-00

Thank you for purchasing a CyberPower product. Please take a few minutes to

www.c

yberpower.com/registration. Registration certifies your product's warranty, confirms your

ownership

in the event of a product loss or theft

and entitles you to free technical support.

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions that should be followed during installation and maintenance of

the UPS and batteries.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled

indoor area free of conductive contaminants. (Please see specifications for acceptable temperature and

humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery.

There are no user serviceable parts inside, except for thebattery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is

disconnected.

CAUTION! The UPS must be connected to an grounded AC power outlet with fuse or circuit breaker

protection. Do not plug into an outlet that is not grounded. If you need to de-energize this equipment, turn off

and unplug the unit.

CAUTION! To avoid electrical shock, turn off the unit and unplug it form the AC power source before

servicing the battery or installing a computer component.

CAUTION! Do not dispose of batteries in a fire. The batteries may explode.

CAUTION! Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may

be toxic.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell

products for life support or medical applications. DO NOT use in any circumstance that would affect

operation and safety of life support equipment, any medical applications or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with

or near an aquarium. Condensation from the aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of fire or electric shock, do not

use the unit on any transportation such as airplanes or ships. The effect of shock or vibration caused during

transit and the damp environment can cause the unit to short out.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit (b) User’s manual (c) USB device cable (d) IEC to IEC power cord

*PowerPanel® Personal Edition software is available on our website. Please visit

www.cyberpower.com and go to the Software Section for free download.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the UPS does not exceed the UPS unit’s rated capacity

(650VA/400W for RT650EI and 500VA/300W for RT500EI). If the rated capacities of the unit are

exceeded, an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to

trip.

2. There are many factors that can affect the amount of power that your electronic equipment will require.

For optimal system performance keep the load below 80% of the unit’s rated capacity.

DESCRIPTION

1. LED Indicators

The LED indicators will illuminate to show the status of power: on line, on battery, overload, replace

battery.

2. Power Switch

To turn the UPS ON, press the power button for approximately 2 seconds - you will hear a constant tone

and release after a short beep.

To turn the UPS OFF, press the power button for approximately 2 seconds - you will hear a constant

tone and release after two short beeps.

Mute mode: The audible alarm can be turned Off or On by quickly pressing the POWER button twice.

The default setting is for the Alarm On. To turn the Alarm Off, quickly press the power button twice. You

will hear two short beeps when the Alarm is turned Off. To turn the Alarm back On, quickly press the

power button twice. You will hear a single short beep when the Alarm is turned On. *When the Alarm is

turned Off, there will be no audible notification when the UPS goes to Battery mode or reaches a low

battery state.

3. Communication Protection Ports

Communication protection ports will protect any standard modem, fax, telephone line, network or

Ethernet connection (RJ11/RJ45).

4. USB Port to PC

The USB port allows connection and communication between the USB port on the computer and the

UPS unit. The UPS communicates its status to the PowerPanel® Personal Edition software.

5. Communication Port to PC

This port allows connection and communication between the UPS and computer. The UPS

communicates its status to the PowerPanel® Personal Edition software. For information regarding

ordering a serial cable for the unit, please contact technical support at CyberPower System.

NOTE: Only one of communication port and USB port can be used as communication and control of the

UPS unit at one time.

6. Battery and Surge Protected Outlets

The unit has battery powered/surge suppression outlets to ensure temporary uninterrupted operation of

your equipment during a power failure. (DO NOT plug a laser printer, paper shredder, copier, space

heater, vacuum cleaner, sump pump, or other large electrical device into the “Battery and Surge

Protected Outlets.” The power demands of these devices will overload and possibly damage the

unit.)

7. Circuit Breaker

Located on the back of the UPS, the circuit breaker serves to provide overload and fault protection.

8. AC Input

Connect the AC Power cord to a properly wired and grounded outlet.

1. Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to ensure

the battery’s maximum charge capacity, it is recommended that you charge the battery for at least 8

hours. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet,

the battery will automatically charge when it’s turned on or turned off.

Note: This UPS is designed with a safety feature to keep the system from being turned on during

shipment. The first time you turn the UPS on, you will need to have it connected to AC power or it

will not power up.

2. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other peripherals

requiring battery backup from the SURGE & BATTERY outlets. DO NOT plug a laser printer, paper

shredder, copier, space heater, vacuum cleaner, sump pump, or other large electrical device into

the “Battery and Surge Protected Outlets”. The power demands of these devices will overload

and possibly damage the unit.

3. To protect a fax, phone, or modem line, connect a telephone cable from the wall jack outlet to the IN jack

of the UPS. Connect a telephone cable from the UPS OUT jack to protect a modem port on the computer,

a telephone, or fax machine.

4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g.

air conditioner, refrigerator, copier, etc.). The warranty prohibits the use of extension cords, outlet strips,

and surge strips in conjunction with the UPS unit.

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this,

turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets.

Make sure the circuit breaker is depressed and then turn the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store the UPS for an extended period of time, cover it and store with the battery fully charged. While in

storage, recharge the battery every three months to ensure optimal battery life.

8. Ensure the wall outlet and UPS are located near the equipment being attached for

proper accessibility.

9. The UPS can lie down on the left direction during operation. DO NOT lie down on

the other side which may block the ventilation hole and hinder the heat dissipation.

CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery.

Service the battery under the supervision of personnel knowledgeable of batteries and their

precautions.

CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.

CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a fire, as they

may explode. Follow all local ordinances regarding proper disposal of batteries.

CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes and

may be toxic.

CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take the following

precautions before replacing the battery:

1. Remove all watches, rings or other metal objects.

2. Only use tools with insulated handles.

3. DO NOT lay tools or other metal parts on top of battery or any battery terminals.

4. Wear rubber gloves and boots.

5. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of ground.

CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of

such shock will be reduced if such grounds are removed during installation and maintenance (applicable to a

UPS and a remote battery supply not having a grounded circuit)

 TO REPLACE THE BATTERY

1. Turn off and unplug all connected equipment.

2. Unplug it from the AC power source.

3. Turn the UPS on its side.

4. Remove the retaining screw.

5. Slide the battery compartment cover completely off of the unit.

6. Remove the battery from the compartment.

7. Disconnect the battery wires from the battery.

8. Install the replacement battery by connecting the red wire and black wire to the positive (+) and

negative (-) terminal of the battery.

9. Put the battery back into the compartment.

10. Slide back the battery compartment cover and tighten the retaining screw.

11. Charge the unit for 8 hours to fully charge the battery.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY INSTRUCTIONS

PRODUCT REGISTRATION

HARDWARE INSTALLATION GUIDE

REPLACING THE BATTERY

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	UPS
Model:	RT650EI
Bredde:	91.4 mm
Dybde:	279.4 mm
Højde:	165.1 mm
Vægt:	4650 g
Produktfarve:	Sort
Pakkevægt:	5200 g
Pakkedybde:	154 mm
Pakkebredde:	382 mm
Pakkehøjde:	217 mm
USB-port:	Ja
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Tower
Responstid:	10 ms
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 95 %
Ethernet LAN-porte (RJ-45):	1
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	0 - 45 °C
Husmateriale:	Plast
Kabler inkluderet:	Input power cable, USB cable
Udgangseffekt:	400 W
Certificering:	CE
LED-indikatorer:	Status, Battery replacement
Kabellængde:	1.83 m
Harmoniseret systemkode (HS):	85078000
Antal understøttede batterier:	1
Opladningstid for batteri:	8 t
Bæredygtighedscertifikater:	RoHS
Medfølgende software:	PowerPanel Personal Edition
Driftshøjde:	0 - 3000 m
Ikke-drift højde:	0 - 15000 m
Indgangsfrekvens:	50/60 Hz
RS-232-porte:	1
Seriel grænsefladetype:	RS-232
Lydalarmer:	Ja
Strømbeskyttelsesfunktioner:	Overbelastning
Strømstik:	C14 forbinder
Modem-porte (RJ-11):	1
AC udgange, antal:	4 AC stikkontakt(er)
AC stikkontakt typer:	C13 forbinder
Overspænding energivurdering:	810 J
Indgående driftsspænding (maks.):	264 V
Output strømkapacitet (VA):	0.65 kVA
Indgående driftsspænding (min.):	192 V
Udgangs driftsspænding (min.):	230 V
Udgangs driftsspænding (maks.):	230 V
UPS topologi:	Standby (offline)
Strøm (maks.):	5 A
Regulering af udgangsfrekvens:	50/60 Hz
Beskyttelse ved overspænding:	Ja
Bølgeform:	Sine
Hørbare alarmtilstande:	Fault, Low battery alarm, Overload alarm
Typisk backup tid ved halv styrke:	15 min.
Typisk backup tid ved fuld styrke:	5 min.
Hot-swap batteri:	Ja
Seriegrænseflade:	Ja
Udgangsspænding total harmonisk forvrængning (THD):	5 %
EMI/RFI støjfiltrering:	Ja
Antal indgående faser:	1
Antal udgående faser:	1