D-Link DAP-2230 Manual

D-Link Ikke kategoriseret DAP-2230

Læs nedenfor 📖 manual på dansk for D-Link DAP-2230 (148 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/148

iD-Link DAP-2230 User Manual

D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any

person or organization of such revisions or changes.

Manual Revisions

Trademarks

D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United

States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of

their respective companies.

from D-Link Corporation, Inc.

Revision DescriptionDate

1.00 June 30, 2015 • Initial release for revision A1

1.10 November 24, 2015 • Minor updates.

1.20 June 24, 2016 • Update for new function

Preface

iiD-Link DAP-2230 User Manual

Table of Contents

Preface i .................................................................................

Product Overview 1 ..............................................................

Package Contents 1 .........................................................................

System Requirements 2 .................................................................

Introduction 3 ...................................................................................

Features 4 ............................................................................................

Hardware Overview 5 .....................................................................

Top Panel 5 .................................................................................

Hardware Overview 6 .....................................................................

Bottom Panel 6 ..........................................................................

Physical Installation 7 ..........................................................

Before You Begin ................................................................... 7

Connect to your Network 8 ..........................................................

Method 1 - Powered by PoE Switch 8 ...............................

Method 2 - Powered by PoE Injector 9 .............................

Method 3 - DC Adapter 10 .....................................................

Mounting the AP 11 ........................................................................

Wireless Installation Considerations 12 ....................................

Four Operational Modes 13 .................................................

Conguration 14 ...................................................................

Web-based Conguration Utility 14 ..........................................

Save and Activate Settings 15 ......................................................

Basic Settings 16 ...............................................................................

Wireless 16 .................................................................................

Access Point mode 16 ........................................................

WDS with AP mode 18 ......................................................

WDS mode 20 .......................................................................

Wireless Client mode 22 ....................................................

Authentication Types ........................................................24

Open System/Shared Key Authentication 24 ...........

WPA/WPA2-Personal Authentication 25 ......................

WPA/WPA2-Enterprise Authentication 26 ..................

802.1x Authentication 27 ..................................................

LAN 28 .........................................................................................

IPv6 29 ..........................................................................................

Advanced Settings 30 .....................................................................

Performance 30 .........................................................................

Wireless Resource Control 32 .......................................................

Multi-SSID 34 ..............................................................................

VLAN 35 ........................................................................................

VLAN List 35 ...........................................................................

Port List 36 ..............................................................................

Add/Edit VLAN ................................................................37

PVID Setting 38 .....................................................................

Intrusion 39 .................................................................................

Schedule 40 ................................................................................

Internal RADIUS Server 41 .....................................................

ARP Spoong Prevention Settings 42 ...............................

Bandwidth Optimization 43 .................................................

AP Array 45 ..................................................................................

Table of Contents

iiiD-Link DAP-2230 User Manual

Table of Contents

AP Array Scan 45 ..................................................................

Conguration Settings 46 .................................................

Auto-RF 47 ..............................................................................

Load Balance 48 ...................................................................

Captive Portal 49 .......................................................................

Authentication Settings-Web Redirection Only 49 .

Authentication Settings- Username/Password 51 ...

Authentication Settings- Passcode 53 .........................

Authentication Settings- Remote RADIUS 55 ............

Authentication Settings- LDAP 57 .................................

Authentication Settings- POP3 59 .................................

IP Filter 62 ....................................................................................

MAC Bypass...........................................................................63

DHCP Server 64 ........................................................................

Dynamic Pool Settings 64 .................................................

Static Pool Setting 65 .........................................................

Current IP Mapping List 66 ...............................................

Filters 67 .......................................................................................

Wireless MAC ACL 67 ..........................................................

WLAN Partition 68 ...............................................................

Trac Control 69 .......................................................................

Uplink/Downlink Settings 69 ..........................................

QoS 70 ......................................................................................

Trac Manager 71 ...............................................................

Status 72 .............................................................................................

Device Information 72 ............................................................

Client Information 73 ..............................................................

WDS Information 74 ................................................................

Channel Analyze 75 .................................................................

Statistics 76 .................................................................................

Ethernet 76 .............................................................................

WLAN Trac ....................................................................77

Log ...........................................................................................78

View Log 78 ............................................................................

Log Settings 79 .....................................................................

Maintenance 81 ...............................................................................

Administration Settings 81 ...................................................

Limit Administrator 82 .......................................................

System Name Settings 83 .................................................

Console Settings 85 ............................................................

SNMP Settings 86 ................................................................

Ping Control 87 .....................................................................

Status: 87 .................................................................................

LED 88 ......................................................................................

LED Status: 88 ........................................................................

Country Settings 89 ............................................................

Select a country: 89 .............................................................

Central WiFiManager Settings ...................................90

Firmware and SSL Certication Upload 91 ..............................

Conguration File Upload 92 .......................................................

Time and Date 93 .............................................................................

System ....................................................................................94

System Settings 94 ..............................................................

Help 95 .................................................................................................

ivD-Link DAP-2230 User Manual

Table of Contents

Wireless Security 96 .............................................................

What is WEP? ................................................................................97

Congure WEP .............................................................................98

What is WPA? ................................................................................99

Congure WPA/WPA2 Personal .......................................... 100

Congure WPA/WPA2 Enterprise ....................................... 101

Connect to a Wireless Network 102 .....................................

Using Windows® XP 102 .................................................................

Congure WPA-PSK ................................................................. 103

Using Windows Vista® 105 ............................................................

Congure WPA-PSK ................................................................. 107

Using Windows® 7 108 ....................................................................

Troubleshooting 111 ............................................................

Wireless Basics 115 ...............................................................

What is Wireless? ...................................................................... 116

Tips 118 ................................................................................................

Wireless Modes 119 .........................................................................

Networking Basics 120 .........................................................

Check your IP address 120 ............................................................

Statically Assign an IP address 121 ............................................

Technical Specications 122 ................................................

Antenna Pattern 124 ............................................................

Regulatory Information 125 ................................................

1D-Link DAP-2230 User Manual

Section 1 - Product Overview

Note: Using a power supply with a dierent rating will cause damage and void the warranty for this product.

Package Contents

DAP-2230 Wireless N PoE Access Point

Quick Installation Guide12 V DC, 1 A Power Adapter (included with

some models)

Wall mounting bracket with

mounting kit

If any of the above items are missing, please contact your reseller.

2D-Link DAP-2230 User Manual

Section 1 - Product Overview

System Requirements

Network Requirements

• An Ethernet-based Network

• IEEE 802.11n/g wireless clients (AP Mode)

• IEEE 802.11n/g wireless network (AP Mode)

Web-based Conguration

Utility Requirements

Computer with the following:

• Windows®, Macintosh, or Linux-based operating system

• An installed Ethernet adapter

Browser Requirements:

• Microsoft Internet Explorer® 7, Mozilla® Firefox® 12.0,

Google® Chrome 20.0, or Safari® 4 or higher

Windows® Users: Make sure you have the latest version of Java installed.

Visit www.java.com to download the latest version.

3D-Link DAP-2230 User Manual

Section 1 - Product Overview

Introduction

The D-Link DAP-2230 Wireless N PoE Access Point is an 802.11n compliant device that delivers real world performance of up to

300 Mbps* while still maintaining backwards compatibility with slower 802.11g and 802.11b devices. The DAP-2230 increases

productivity by allowing you to work faster and more eciently. With the DAP-2230, bandwidth-intensive applications like

graphics or multimedia will benet signicantly because large les are now able to move across the network more quickly.

Create a secure wireless network to share photos, les, music, video, printers, and network storage outside of your normal

internal networking environment. Built to withstand harsh environments, the DAP-2230 also excels in connecting separate

networks that cannot be joined physically using a traditional medium. The built-in omni-directional 3 dBi antenna is designed

to deliver high performance, ensuring that wireless coverage will cover even hard to reach locations. The DAP-2230 is an ideal

solution for quickly creating and extending a wireless local area network (WLAN) in oces or other workplaces, hotels, resorts,

trade shows, and special events.

The DAP-2230 features four dierent operation modes: Access Point, Wireless Distribution System (WDS), WDS with AP, and

Wireless Client mode, allowing it to adapt to many situations. As a standard wireless Access Point (AP) the DAP-2230 can connect

to a wide range of devices that are 802.11 n/g/b compliant. In WDS mode it can expand current wireless coverage without the

need for a wired backbone link. As a wireless client it can connect to an existing AP, and expand the network physically with

the built-in 10/100 Ethernet port.

The DAP-2230 supports 64/128-bit WEP data encryption and WPA/WPA2 security functions. In addition, it provides MAC Address

Filtering to control user access, and the Disable SSID Broadcast function to limit unauthorized access to the internal network.

Network administrators have multiple options for managing the DAP-2230, including Web (HTTP) or Secured Web (HTTPS).

For advanced network management, administrators can use SNMP v1, v2c, v3 to congure and manage access points.

*Maximum wireless signal rate derived from IEEE Standard 802.11n and 802.11g specications. Actual data throughput may vary. Network conditions

and environmental factors, including volume of network trac, building materials and construction, and network overhead can lower actual data

throughout rate.

4D-Link DAP-2230 User Manual

Section 1 - Product Overview

• Faster Wireless Networking - The DAP-2230 provides an up to 300 Mbps* wireless connection with other 802.11n

wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online

gaming, and real-time audio.

• Compatible with IEEE802.11g Devices - The DAP-2230 is still fully compatible with the 802.11g standards, so it can

connect with existing 802.11g adapters.

• Four dierent operation modes - Capable of operating in one of four dierent operation modes to meet your wireless

networking needs: Access Point, WDS with AP, WDS, and Wireless Client.

• Power over Ethernet - The DAP-2230 supports IEEE 802.3af PoE (Power over Ethernet) which enables it to be supplied

with power over an Ethernet cable or IEEE 802.3af PoE switch.

• Comprehensive Web-Interface - Fine tune network settings using the DAP-2230’s robust network-based conguration

software.

• Central WiFiManager management software compatibility - The real-time display of the network’s topology and

AP’s information makes network conguration and management of multiple devices quick and simple.

• SNMP for management - The DAP-2230 supports SNMP v1, v2c, and v3 for better network management. Superior

wireless AP manager software is bundled with the DAP-2230 for network conguration and rmware upgrade.

Systems administrators can also set up the DAP-2230 easily with the Web-based conguration utility.

• Convenient Installation - The DAP-2230 features a wall mount in the rear for easy setup on walls.

Features

6D-Link DAP-2230 User Manual

Section 1 - Product Overview

Hardware Overview

Bottom Panel

1Security Lock Physically secure your device with this lock.

2Power Connector Connector for a power adapter.

310/100 LAN (PoE)Port Connect an Ethernet cable to this device and your network. Power may be supplied

to this port via a LAN cable that is connected to a PoE injector or PoE switch.

4Reset Button

Press and hold the reset button with a paperclip for at least 5 seconds to reset the

device back to the factory default settings. The LED will turn on for 2 seconds and

then begin the reboot process.

1 2 3 4

voltage

7D-Link DAP-2230 User Manual

Section 2 - Installation

This chapter describes safety precautions and product information that you must know and check before installing this product.

Physical Installation

Before You Begin

Professional Installation Required

1. Please seek assistance from a professional installer who is well trained in RF installation and knowledgeable about local

regulations.

2. This product is distributed through distributors and system installers with professional technicians and is not to be sold

directly through retail stores.

8D-Link DAP-2230 User Manual

Section 2 - Installation

Connect to your Network

Method 1 - Powered by PoE Switch

To power the access point, you can use one of the following 3 methods:

Method 1 - Powered by PoE Switch

Method 2 - Powered by PoE Injector

Method 3 - Powered by DC Adapter

1. Connect one end of an Ethernet cable into the LAN (PoE) port on the DAP-2230 and then connect the other end to a PoE

switch.

DAP-2230

PoE Switch

9D-Link DAP-2230 User Manual

Section 2 - Installation

Method 2 - Powered by PoE Injector

If you wish to power the DAP-2230 without a PoE switch, we suggest you use a PoE injector, such as a DPE-101GI.

1. Connect one end of an Ethernet cable into the DATA IN port on the PoE injector and the other end into a port on a switch,

router, or computer.

2. Connect one end of a dierent Ethernet cable into the P+DATA OUT port on the PoE injector and the other end into the LAN

(PoE) port on the DAP-2230 access point.

3. Connect the supplied power adapter to the connector on the PoE Injector.POWER IN

4. Plug the power adapter into a power outlet.

DAP-2230

PC Switch

Power

adapter PoE Base

Unit

10D-Link DAP-2230 User Manual

Section 2 - Installation

A power adapter is included with some DAP-2230 models.

1. Connect an Ethernet cable from your network device to the LAN(PoE) port on the DAP-2230.

2. Connect the supplied power adapter to the connector on the DAP-2230.DC IN

3. Plug the power adapter into a power outlet.

Method 3 - DC Adapter

DAP-2230

Switch or Router

Power Adapter

11D-Link DAP-2230 User Manual

Section 2 - Installation

Mounting the AP

Place the mounting bracket on a wall or ceiling and mark holes

where you will insert the screws with a marker. Drill holes in the

marked points and insert the plastic wall anchors.

Use the supplied screws to attach the mounting plate to the wall.

Reattach the DAP-2230 to the mounting bracket.

12D-Link DAP-2230 User Manual

Section 2 - Installation

Wireless Installation Considerations

The D-Link DAP-2230 Wireless N PoE Access Point lets you access your network using a wireless connection from virtually

anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location

of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending

on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless

range is to follow these basic guidelines:

1. Keep the number of walls and ceilings between the D-Link access point and other network devices to a minimum.

Each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters). Position your devices so that

the number of walls or ceilings is minimized.

2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree

angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick!

Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better

reception.

3. Building materials make a dierence. A solid metal door or aluminum studs may have a negative eect on

range. Try to position access points, wireless access points, and computers so that the signal passes through

drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (sh

tanks), mirrors, le cabinets, brick, and concrete will degrade your wireless signal.

4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF

noise.

5. If you are using 2.4 Ghz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security

systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4 Hz phone

base is as far away from your wireless devices as possible. The base transmits a signal even if the phone is not

in use.

14D-Link DAP-2230 User Manual

Section 3 - Conguration

Conguration

This section will show you how to congure your new D-Link Wireless N PoE Access Point using the web-based conguration

utility.

Web-based Conguration Utility

If you wish to change the default settings or optimise the

performance of the DAP-2230, you may use the web-

based conguration utility.

To access the conguration utility, open a web browser

such as Internet Explorer and enter http://192.168.0.50

or https://192.168.0.50

Type and then enter your password. Leave the admin

password blank by default.

If you get a Page Cannot be Displayed error, please refer

to “Troubleshooting” on page 111 for assistance.

15D-Link DAP-2230 User Manual

Section 3 - Conguration

After successfully logging into the DAP-2230, the following screen will appear:

When making changes on most of the conguration screens in this section, use the button at the bottom of each

screen to save (not activate) your conguration changes.

You may change settings to multiple pages before activating. Once you are nished, click the Conguration button located

at the top of the page and then click Save and Activate.

Save and Activate Settings

16D-Link DAP-2230 User Manual

Section 3 - Conguration

Basic Settings

Wireless

Access Point mode

Wireless

Band:

Select 2.4 Ghz from the drop-down menu.

Mode: Select Access Point from the drop-down menu.

The other three choices are WDS with AP, WDS wireless Client, and .

Network

Name

(SSID):

Service Set Identier (SSID) is the name designated for a specic wireless

local area network (WLAN). The SSID’s factory default setting is dlink. The

SSID can be easily changed to connect to an existing wireless network or

to establish a new wireless network. The SSID can be up to 32 characters

and is case-sensitive.

SSID

Visibility:

Enable Disable or SSID visibility. Enabling this feature broadcasts the SSID

across the network, thus making it visible to all network users. This feature

is enabled by default.

Auto

Channel

Selection:

Enabling this feature automatically selects the channel that provides the

best wireless performance. is set by default. The channel selection Enable

process only occurs when the AP is booting up.

Channel: All devices on the network must share the same channel. To change the

channel, rst toggle the Auto Channel Selection setting to , and then Disable

use the drop-down menu to make the desired selection.

Note: The wireless adapters will automatically scan and match the wireless

settings.

17D-Link DAP-2230 User Manual

Section 3 - Conguration

Channel

Width:

Allows you to select the channel width you would like to operate in. Select

20 MHz if you are not using any 802.11n wireless clients. Auto 20/40 MHz

allows you to connect to both 802.11n and 802.11b/g wireless devices on

your network.

Authentication: Use the drop-down menu to choose Open System Shared Key, , WPA-

Personal WPA-Enterprise 802.11x, , or .

Select Open System to communicate the key across the network.

Select Shared Key to limit communication to only those devices that share

the same WEP settings. If multi-SSID is enabled, this option is not available.

Select WPA-Personal to secure your network using a password and dynamic

key changes. No RADIUS server is required.

Select WPA-Enterprise to secure your network with the inclusion of a RADIUS

server.

Select 802.1x to secure your network using 802.1x authentication.

18D-Link DAP-2230 User Manual

Section 3 - Conguration

WDS with AP mode

In WDS with AP mode, the DAP-2230 wirelessly connects multiple networks while still functioning as a wireless AP.

Wireless

Band:

Select from the drop-down menu. 2.4 Ghz

Mode: WDS with AP mode is selected from the drop-down menu.

The other three choices are Access Point, WDS, and wireless Client.

Network

Name

(SSID):

Service Set Identier (SSID) is the name designated for a specic wireless

local area network (WLAN). The SSID’s factory default setting is dlink. The

SSID can be easily changed to connect to an existing wireless network or to

establish a new wireless network.

SSID

Visibility:

Enable Disable or SSID visibility. Enabling this feature broadcasts the SSID

across the network, thus making it visible to all network users.

Auto

Channel

Selection:

Enabling this feature automatically selects the channel that will provide the

best wireless performance. This feature is not supported in WDS with AP

mode. The channel selection process only occurs when the AP is booting up.

Channel: To change the channel, use the drop-down menu to make the desired

selection. ( The wireless adapters will automatically scan and match Note:

the wireless settings.)

Channel

Width:

Indicates whether the device is capable of 20 MHz operation only or both

20 MHz and 40 MHz operation.

Remote AP

MAC Address:

Enter the MAC addresses of the APs on your network that will serve as bridges

to wirelessly connect multiple networks.

Site Survey: Click on the button to search for available wireless networks, then click Scan

on the available network that you want to connect with.

19D-Link DAP-2230 User Manual

Section 3 - Conguration

Authentication: Use the drop-down menu to choose Open System WPA-Personal or .

Select Open System to communicate the key across the network.

Select WPA-Personal to secure your network using a password and dynamic

key changes. No RADIUS server is required.

20D-Link DAP-2230 User Manual

Section 3 - Conguration

WDS mode

In WDS mode, the DAP-2230 wirelessly connects multiple networks, without functioning as a wireless AP.

Wireless

Band:

Select from the drop-down menu. 2.4 Ghz

Mode: WDS is selected from the drop-down menu.

The other three choices are Access Point, WDS with AP wireless Client, and .

Network

Name

(SSID):

Service Set Identier (SSID) is the name designated for a specic wireless

local area network (WLAN). The SSID’s factory default setting is dlink. The

SSID can be easily changed to connect to an existing wireless network or to

establish a new wireless network.

SSID

Visibility:

Enable Disable or SSID visibility. Enabling this feature broadcasts the SSID

across the network, thus making it visible to all network users.

Auto

Channel

Selection:

Enabling this feature automatically selects the channel that will provide the

best wireless performance. This feature is not supported in WDS with AP

mode. The channel selection process only occurs when the AP is booting up.

Channel: To change the channel, use the drop-down menu to make the desired

selection. ( The wireless adapters will automatically scan and match Note:

the wireless settings.)

Channel

Width:

Indicates whether the device is capable of 20 MHz operation only or both

20 MHz and 40 MHz operation.

Remote

AP MAC

Address:

Enter the MAC addresses of the APs on your network that will serve as bridges

to wirelessly connect multiple networks.

Site Survey: Click on the button to search for available wireless networks, then click Scan

on the available network that you want to connect with.

21D-Link DAP-2230 User Manual

Section 3 - Conguration

Authentication: Use the drop-down menu to choose Open System WPA-Personal or .

Select Open System to communicate the key across the network.

Select WPA-Personal to secure your network using a password and dynamic

key changes. No RADIUS server is required.

22D-Link DAP-2230 User Manual

Section 3 - Conguration

Wireless Client mode

Wireless

Band:

Select from the drop-down menu. 2.4 Ghz

Mode: Wireless Client is selected from the drop-down menu.

The other three choices are Access Point, WDS with AP WDS, and .

Network

Name

(SSID):

Service Set Identier (SSID) is the name designated for a specic wireless

local area network (WLAN). The SSID’s factory default setting is dlink. The

SSID can be easily changed to connect to an existing wireless network or to

establish a new wireless network.

SSID

Visibility:

Enable Disable or SSID visibility. Enabling this feature broadcasts the SSID

across the network, thus making it visible to all network users. Disabling

SSID is not supported in Wireless Client mode.

Auto

Channel

Selection:

Enabling this feature automatically selects the channel that will provide

the best wireless performance. This feature is automatically enabled in

Wireless Client mode. The channel selection process only occurs when the

AP is booting up.

Channel: To change the channel, use the drop-down menu to make the desired

selection. ( The wireless adapters will automatically scan and match Note:

the wireless settings.)

Channel

Width:

Indicates whether the device is capable of 20 MHz operation only or both

20 MHz and 40 MHz operation.

Click on the button to search for available wireless networks, then Scan

click on the available network that you want to connect with.

23D-Link DAP-2230 User Manual

Section 3 - Conguration

Authentication: Use the drop-down menu to choose Open System WPA-Personal or .

Select Open System to communicate the key across the network.

Select WPA-Personal to secure your network using a password and

dynamic key changes. No RADIUS server is required.

Wireless Mac

Clone Enable:

Check to enable clone MAC. This feature will allow you to change the MAC

address of the access point to the MAC address of a client.

MAC Source: Select the MAC source from the drop-down menu.

MAC Address: Enter the MAC address that you would like to assign to the access point.

25D-Link DAP-2230 User Manual

Section 3 - Conguration

WPA/WPA2-Personal Authentication

WPA Mode: When WPA-Personal is selected for Authentication type, you must also select

a WPA mode from the drop-down menu: AUTO (WPA or WPA2), WPA2 Only,

or WPA Only. WPA and WPA2 use dierent algorithms. AUTO (WPA or WPA2)

allows you to use both WPA and WPA2.

Cipher Type: When you select WPA-Personal, you must also select AUTO, AES, or TKIP

from the drop-down menu.

Group Key

Update:

Select the interval during which the group key will be valid. The default value

of is recommended.3600

Select to enter your key (PassPhrase). Manual

You can select Periodical Key Change to have the access point automatically

change your PassPhrase.

Periodical

Key Change:

Enter the Activate From time and the time in hours to change the key.

PassPhrase: When you select WPA-Personal, please enter a PassPhrase in the

corresponding eld.

Conrm

PassPhrase:

Type the passphrase again to guard against typos.

WPA/WPA2 Personal Authentication can be enabled for Access Point WDS with AP Wireless Client , , WDS, and modes.

26D-Link DAP-2230 User Manual

Section 3 - Conguration

WPA/WPA2-Enterprise Authentication

WPA Mode: When WPA-Enterprise is selected, you must also select a WPA mode from

the drop-down menu: AUTO (WPA or WPA2) WPA2 Only WPA Only, , or .

WPA and WPA2 use dierent algorithms. AUTO (WPA or WPA2) allows you

to use both WPA and WPA2.

Cipher

Type:

When WPA-Enterprise is selected, you must also select a cipher type from

the drop-down menu: , , or .Auto AES TKIP

Group Key

Update

Interval:

Select the interval during which the group key will be valid. The recommended

value is A lower interval may reduce data transfer rates.3600.

Network

Access

Protection:

Enable or disable Microsoft Network Access Protection.

RADIUS

Server:

Enter the IP address of the RADIUS server.

RADIUS

Port:

Enter the RADIUS port.

RADIUS

Secret:

Enter the RADIUS secret.

WPA/WPA2 Enterprise Authentication can only be enabled for Access Point mode.

27D-Link DAP-2230 User Manual

Section 3 - Conguration

802.1x Authentication

Key Update

Interval:

Select the interval during which the group key will be valid ( is the 300

recommended value). A lower interval may reduce data transfer rates.

RADIUS

Server:

Enter the IP address of the RADIUS server.

RADIUS

Port:

Enter the RADIUS port.

RADIUS

Secret:

Enter the RADIUS secret.

802.1x Authentication can only be enabled for Access Point mode.

28D-Link DAP-2230 User Manual

Section 3 - Conguration

LAN

LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for

the DAP-2230. These settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP

address is private to your internal network and cannot be seen on the Internet.

Get IP From: Static IP (Manual) is chosen here. Choose this option if you do not have a

DHCP server in your network, or if you wish to assign a static IP address to

the DAP-2230. When Dynamic IP (DHCP) is selected, the other elds here

will be grayed out. Please allow about two minutes for the DHCP client to

be functional once this selection is made.

IP Address: The default IP address is 192.168.0.50. Assign a static IP address that is within

the IP address range of your network.

Subnet

Mask:

Enter the subnet mask. All devices in the network must share the same

subnet mask.

Default

Gateway:

Enter the IP address of the gateway in your network. If there is a gateway in

your network, please enter an IP address within the range of your network.

DNS: Enter the DNS IP address used here.

29D-Link DAP-2230 User Manual

Section 3 - Conguration

IPv6

Enable IPv6: Check to enable the IPv6.

Get IP From: Auto is the default option. The DAP-2230 will get an IPv6 address

automatically or use to set IPv6 address manually. When Auto is Static

selected, the other elds here will be grayed out.

IP Address: Enter the LAN IPv6 address used here.

Prex: Enter the LAN subnet prex length value used here.

Default

Gateway:

Enter the LAN default gateway IPv6 address used here.

30D-Link DAP-2230 User Manual

Section 3 - Conguration

Advanced Settings

Performance

*Maximum wireless signal rate derived from IEEE Standard 802.11n and 802.11g specications. Actual data throughput may vary. Network conditions and environmental factors,

including volume of network trac, building materials and construction, and network overhead can lower actual data throughout rate.

Wireless: Use the drop-down menu to turn the wireless function or .On O

Wireless

Mode:

The dierent combination of clients that can be supported include Mixed

802.11n, 802.11g and 802.11b Mixed 802.11g and 802.11b 802.11n , and

Only. Please note that when backwards compatibility is enabled for legacy

(802.11g/b) clients, degradation of 802.11n wireless performance is expected.

Data Rate*: Indicate the base transfer rate of wireless adapters on the wireless LAN.

The AP will adjust the base transfer rate depending on the base rate of the

connected device. If there are obstacles or interference, the AP will step down

the rate. This option is enabled in Mixed 802.11g and 802.11b mode. The

choices available are Best (Up to 54), 54, 48, 36, 24, 18, 12, 9, 6, 11, 5.5, 2 or 1.

Beacon

Interval (25-

500):

Beacons are packets sent by an access point to synchronize a

wireless network. Specify a value in milliseconds. The default ( ) is 100

recommended. Setting a higher beacon interval can help to save the

power of wireless clients, while setting a lower one can help a wireless

client connect to an access point faster.

DTM

Interval

(1-15):

Select a Delivery Trac Indication Message setting between and . 1 15

The default value is . DTIM is a countdown informing clients of the next 1

window for listening to broadcast and multicast messages.

Transmit

Power:

This setting determines the power level of the wireless transmission.

Transmitting power can be adjusted to eliminate overlapping of wireless

area coverage between two access points where interference is a major

concern. For example, if wireless coverage is intended for half of the area,

then select as the option. Use the drop-down menu to select , 50% 100%

50% 25% 12.5%, , or .

31D-Link DAP-2230 User Manual

Section 3 - Conguration

WMM (Wi-Fi

Multimedia):

WMM stands for Wi-Fi Multimedia. Enabling this feature will improve the

user experience for audio and video applications over a Wi-Fi network.

Ack Time Out

(2.4 GHZ,

64~200):

To eectively optimize throughput over long distance links, enter a value

for Acknowledgement Time Out from microseconds in the 2.4 64 to 200

GHz in the eld provided.

Short GI: Select or . Enabling a short guard interval can increase Enable Disable

throughput. However, be aware that it can also increase the error rate

in some installations due to increased sensitivity to radio-frequency

installations.

IGMP

Snooping:

Select or . Internet Group Management Protocol allows Enable Disable

the AP to recognize IGMP queries and reports sent between routers and

an IGMP host (wireless STA). When IGMP snooping is enabled, the AP

will forward multicast packets to an IGMP host based on IGMP messages

passing through the AP.

Multicast Rate: Select the multicast rate for 2.4G band.

Multicast

Bandwidth

Control:

Adjust the multicast packet data rate here. The multicast rate is supported

in AP mode and WDS with AP mode, including Multi-SSIDs.

Maximum

Multicast

Bandwidth :

Set the multicast packets maximum bandwidth pass through rate from

the Ethernet interface to the Access Point.

HT20/40

Coexistence:

Enable this option to reduce interference from other wireless networks in

your area. If the channel width is operating at 40 MHz and there is another

wireless network’s channel over-lapping and causing interference, the

Access Point will automatically change to 20 MHz.

Transfer

DHCP Oer

to Unicast :

Enable to transfer the DHCP Oer to Unicast from LAN to WLAN, it is

recommended to enable this function if the number of stations is larger

than 30.

32D-Link DAP-2230 User Manual

Section 3 - Conguration

Wireless Resource Control

The Wireless Resource Control window is used to congure the wireless connection settings so that devices can detect and

connect to the Access Point with the strongest signal.

Wireless band: Select .2.4 Ghz

Connection

Limit:

Select or . This is an option for load balancing. This de-Enable Disable

termines whether to limit the number of users accessing this device. The

exact number is entered in the User Limit eld below. This feature allows

the user to share the wireless network trac and the client using multiple

APs. If this function is enabled and when the number of users exceeds this

value, or the network utilization of this AP exceeds the percentage that

has been specied, the DAP-2230 will not allow clients to associate with

the AP.

User Limit: Set the maximum amount of users that are allowed access (zero to 64 us-

ers) to the device using the specied wireless band. The default setting is

20.

11n

Preferred:

Use the drop-down menu to the 11n Preferred function. The wire-Enable

less clients with 802.11n protocol will have higher priority to connect to

the device.

Network

Utilization:

Set the maximum utilization of this access point. The DAP-2230 will not

allow any new clients to associate with the AP if the utilization exceeds

the specied value. Select a utilization percentage between 100%, 80%,

60%, 40%, 20%, or 0%. When this network utilization threshold is reached,

the device will pause for one minute to allow network congestion to dis-

sipate.

Aging out: Use the drop-down menu to select the criteria of disconnecting the wire-

less clients. Available options are and .RSSI Data Rate

33D-Link DAP-2230 User Manual

Section 3 - Conguration

RSSI

Threshold:

When is selected in the drop-down menu, select the per-RSSI Aging out

centage of RSSI here. When the RSSI of wireless clients is lower than the

specied percentage, the device disconnects the wireless clients.

Data Rate

Threshold:

When is selected in the Data Rate Aging out drop-down menu, select

the threshold of data rate here. When the data rate of wireless clients is

lower than the specied number, the device disconnects the wireless

clients.

ACL RSSI: Use the drop-down menu to the function. When enabled, the de-Enable

vice denies the connection request from the wireless clients with the RSSI

lower than the specied threshold below.

ACL RSSI

Threshold:

Set the ACL RSSI Threshold.

35D-Link DAP-2230 User Manual

Section 3 - Conguration

VLAN

VLAN List

The DAP-2230 supports VLANs. VLANs can be created with a Name and VID. Mgmt (TCP stack), LAN, Primary Multiple SSID, and

WDS connection can be assigned to VLANs as they are physical ports. Any packet which enters the DAP-2230 without a VLAN

tag will have a VLAN tag inserted with a PVID.

The VLAN List tab displays the current VLANs.

VLAN

Status:

Use the radio button to toggle between or . Next, go to the Enable Disable

Add/Edit VLAN tab to add or modify an item on the tab.VLAN List

37D-Link DAP-2230 User Manual

Section 3 - Conguration

Add/Edit VLAN

The Add/Edit VLAN tab is used to congure VLANs. Once you have made the desired changes, click the button to let Save

your changes take eect.

VLAN

Status:

Use the radio button to toggle to Enable.

VLAN ID: Provide an ID number between and for the Internal VLAN.1 4094

VLAN

Name:

Enter the VLAN to add or modify.

40D-Link DAP-2230 User Manual

Section 3 - Conguration

Schedule

The Wireless Schedule Settings window is used to add and modify scheduling rules on the device. Click the Save button to let

your changes take eect.

Wireless

Schedule:

Use the drop-down menu to enable the device’s scheduling feature.

Name: Enter a name for the new scheduling rule in the eld provided.

Index: Select the SSID the schedule will apply to from the drop-down menu.

SSID: Enter the name of your wireless network (SSID).

Day(s): Toggle the radio button between All Week and Select Day(s). If the second

option is selected, check the specic days you want to apply the rule to.

All Day(s): Check this box to have your settings apply 24 hours a day.

Start Time: Enter the start time for your rule. If you selected All Day, this option will be

greyed out.

End Time: Enter the end time for your rule.

Add: Click to add the rule to the list.

Schedule

Rule List:

This section will display the list of created schedules.

Save: Click the Save button to save your created rules.

41D-Link DAP-2230 User Manual

Section 3 - Conguration

Internal RADIUS Server

The DAP-2230 features a built-in RADIUS server. Once you have nished adding a RADIUS account, click the button to Save

have your changes take eect. The newly-created account will appear in this RADIUS Account List. The radio buttons allow the

user to enable or disable the RADIUS account. Click the icon in the delete column to remove the RADIUS account. We suggest

you limit the number of accounts to under 30.

User Name: Enter a name to authenticate user access to the internal RADIUS server.

Password: Enter a password to authenticate user access to the internal RADIUS server.

The length of your password should be 8~64.

Status: Toggle the drop-down menu between Enable and Disable.

RADIUS

Account List:

Displays the list of users.

42D-Link DAP-2230 User Manual

Section 3 - Conguration

ARP Spoong Prevention Settings

The ARP Spoong Prevention feature allows users to add IP/MAC address mapping to prevent spoong attacks.ARP

ARP

Spoong

Prevention:

This check box allows you to enable the ARP spoong prevention function.

Gateway

IP Address:

Enter a gateway IP address.

Gateway

MAC Address:

Enter a gateway MAC address.

Produkt Specifikationer

Mærke:	D-Link
Kategori:	Ikke kategoriseret
Model:	DAP-2230
Vekselstrømsindgangsspænding:	12 V
Bredde:	129 mm
Dybde:	129 mm
Højde:	29 mm
Vægt:	213.6 g
Produktfarve:	Hvid
Pakkevægt:	350 g
Pakkedybde:	158 mm
Pakkebredde:	144 mm
Pakkehøjde:	59 mm
Opbevaringstemperatur (T-T):	-20 - 65 °C
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 95 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 40 °C
Ethernet LAN-datahastigheder:	10, 100 Mbit/s
Sikkerhedsalgoritmer:	64-bit WEP, 128-bit WEP, WPA, WPA2
Certificering:	FCC, IC, CE, UL, Wi-Fi® Certified
Strømforbrug (maks.):	5.76 W
Pallens bruttobredde:	1100 mm
Pallens bruttolængde:	1200 mm
Netværksstandarder:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3af, IEEE 802.3u
DC-in-stik:	Ingen
Antenner, antal:	2
Webbaseret administration:	Ja
Servicekvalitet support (QoS):	Ja
LED-indikatorer:	Power, Status
Antal brugere:	- bruger(e)
Frekvensbånd:	2.4 - 2.4835 GHz
Intern:	Ingen
Maksimal dataoverførselshastighed:	300 Mbit/s
Indgangsstrøm:	1 A
Forsendelseskassens bruttovægt (indvendig):	7870 g
Strøm over Ethernet (PoE):	Ja
Produkter pr. forsendelseskasse (indvendig):	20 stk
Monteringssæt:	Ja
Forsendelseskasses kassens bredde (indvendig):	324 mm
Forsendelseskassens længde (indvendig):	333 mm
Forsendelseskassens højde (indvendig):	327 mm
Forsendelsesemballage nettovægt:	4600 g
Filtrering af MAC-adresser:	Ja
2.4 GHz:	Ja
5 GHz:	Ingen
Antennefunktioner:	Integreret antenne
Antal SSID understøttet:	8
Niveau for antennestyrke (maks.):	3 dBi
Båndbredde:	2.4 GHz
Palle bruttovægt (luft):	442980 g
Antal papkasser pr. palle (luft):	54 stk
Antal pr. palle (luft):	1080 stk
Pallehøjde (luft):	2097 mm
Palle bruttovægt (hav):	442980 g
Antal papkasser pr. palle (hav):	54 stk
Antal pr. palle (hav):	1080 stk
Pallehøjde (hav):	2097 mm