Daizuki DXTH36X426-17 Manual

Daizuki Aircondition DXTH36X426-17

Læs nedenfor 📖 manual på dansk for Daizuki DXTH36X426-17 (30 sider) i kategorien Aircondition. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/30
SAFETY RULES AND RECOMMENDATIONS FOR THE INSTALLER
NAMES OF THE PARTS
INDOOR UNIT DISPLAY
OPERATING INSTRUCTIONS
PROTECTION
INSTALLATION
MAINTENANCE
TROUBLESHOOTING
EMERGENCY FUNCTION & AUTO-RESTART FUNCTION
REMOTE CONTROL
......................1
........................................................................................................4
.........................................................................................................5
..............................................6
...............................................................................................................7
..............................................................................................11
.........................................................................................................................17
.....................................................................................................................18
....................................................................................................................27
..........................................................................................................28
CONTENTS
1
During the installation of the indoor and outd-
oor units the access to the working area should
be forbidden to children.
Unforeseeable accidents could happen.
Make sure that the base of the outdoor unit is
firmly fixed.
Check that air cannot enter the refrigerant sys-
tem and check for refrigerant leaks when mo-
ving the air conditioner.
SAFETY RULES AND RECOMMENDATIONS FOR THE INSTALLER
Carry out a test cycle after installing the air co-
nditioner and record the operating data.
The ratings of the fuse installed in the built in-
control unit are T 5A / 250V.
The user must protect the indoor unit with a
fuse of suitable capacity for the maximum in-
put current or with another overload protection
device.
Ensure that the mains voltage corresponds to
that stamped on the rating plate . Keep the sw-
itch or power plug clean. Insert the power plug
correctly and firmly into the socket, thereby a-
voiding the risk of electric shock or fire due to
insufficient contact.
Check that the socket is suitable for the plug ,
otherwise have the socket changed.
Do not install the appliance at a distance of
less than 20 from inflammable substances ”
(alcohol, etc.) Or from pressurised containers
(e.g. spray cans).
If the appliance is used in areas without the
possibility of ventilation, precautions must be
taken to prevent any leaks of refrigerant gas
from remaining in the environment and creat-
ing a danger of fire
The packaging materials are recyclable and
should be disposed of in the separate waste
bins .Take the air conditioner at the end of its
life to waste collection center
for disposal.
an authorized
Only use the air conditioner as instructed in
this booklet . These instructions are not inten-
ded to cover every possible condition and
situation . As with any electrical household
appliance , common sense and caution are
therefore always recommended for installat-
ion, operation andmaintenance.
The appliance must be installed in accordance
with applicable national regulations.
Before accessing the terminals , all the power
circuits must be disconnected from the power
supply.
Read this guide before installing and using the
appliance.
The appliance must be fitted with means for
disconnection from the supply mains having
a contact separation in all poles that provide
full disconnection under overvoltage
category III conditions, and these means
must be incorporated in the fixed wiring in
accordance with the wiring rules.
Installation must be preformed in accorda-
nce with the requirements of NEC and CEC
by authorized personnel only.
This appliance can be used by children a-
ged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and kn-
owledge if they have been given supervis-
ion or instruction concerning use of the a-
ppliance in a safe way and understand the
hazards involved. Children shall not play
with the appliance. Cleaning and user ma-
intenance shall not be made by children
without supervision.
The air conditioner must be installed by
professional or qualified persons.
SAFETY RULES AND RECOMMENDATIONS FOR THE USER
Do not try to install the alone;
always contact specialized technical personnel.
air condition
Cleaning and maintenance must be carried out
by specialised technical personnel. In any case
disconnect the appliance from the mains elect-
ricity supply before carrying out any cleaning
or maintenance.
Ensure that the mains voltage corresponds to
that stamped on the rating plate. Keep the swi-
tch and power plug clean. Insert the power plug
correctly and firmly into the socket , thereby
avoiding the risk of electric shock or fire due
to insufficient contact.
Do not pull out the plug to switch off the app-
liance when it is in operation, since this could
create a spark and cause a fire, etc.
If the appliance gives off smoke or there is a
smell of burning, immediately cut off the pow
er supply and contact
.
an authorized service
center
Have repairs carried out only by an
. Incorrect repair could expose
the user to the risk of electric shock, etc.
authorized
Service Center.
The prolonged use of the device in such
conditions could cause fire or electrocution.
Never remain directly exposed to the flow of
cold air for a long time. The direct and prolo-
nged exposition to cold air could be dangero-
us for your health .Particular care should be
taken in the rooms where there are children,
old or sick people.
This appliance has been made for air conditi-
oning domestic environments and must not be
used for any other purpose , such as for drying
clothes, cooling food, etc.
The packaging materials are recyclable and
should be disposed of in waste
bins . Take the air conditioner at the end of its
life to waste collection
for disposal.
separate
an authorized center
Only use the air conditioner as instructed in
this booklet.These instructions are not intend-
ed to cover every possible condition and situ-
ation.As with any electrical household applia-
nce, common sense and caution are therefore
always recommended for installation , operat-
ion and maintenance.
Always use the appliance with the air filter
mounted .The use of the conditioner without
air filter could cause an excessive accumulation
of dust or waste on the inner parts of the device
with possible subsequent failures.
air
Unhook the automatic switch if you foresee
not using the device for a long time.
The airflow direction must be properly adjus-
ted.
The user is responsible for having the appliance
installed by a qualified technician , who must
check that it is earthed in accordance with curr-
ent legislation and insert a thermomagnetic cir-
cuit breaker.
Ensure that the appliance is disconnected from
the power supply when it will remain inoperat-
ive for a long period and before carrying out
any cleaning or maintenance.
Selecting the most suitable temperature can pr-
event damage to the appliance.
The flaps must be directed downwards in
the heating mode and upwards in the cooling
mode.
The batteries in the remote control must be rec-
ycled or disposed of properly. Disposal of Scrap
Batteries - Please discard the batteries as sorted
municipal waste at the accessible collection
point.
2
Do not bend, tug or compress the power cord
since this could damage it. Electrical shocks or
a damaged power cord.
z technical personnel only must repl-
ace a damaged power cord.
ire are be caused by
Speciali ed
Do not use extensions or gang modules.
Do not touch the appliance when barefoot or
parts of the body are wet or damp.
Do not obstruct the air inlet or outlet of the in-
door or the outdoor unit.
The obstruction of these openings causes a re-
duction in the operative efficiency of the
with possible consequent failures
or damages.
air
conditioner
In no way alter the characteristics of the appli-
ance.
Do not install the appliance in environments
where the air could contain gas, oil or sulphur
or near sources of heat.
Do not climb onto or place any heavy or hot
objects on top of the appliance.
Do not leave windows or doors open when the
air conditioner is operating.
Do not direct the airflow onto plants or anim-
als.
A long direct exposition to the flow of cold
air of the conditioner could have negative
effects on plants and animals.
Do not put the conditioner in contact with
water.
The electrical insulation could be damaged
and thus causing electrocution.
Do not climb onto or place any objects on the
outdoor unit
Never insert your finger,a stick,etc. into the air
inlet / outlet. Doing so could cause injury.
This appliance is not intended for use by
persons (including children ) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge, un-
less they have been given supervision or in-
struction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in
order to avoid a hazard.
3
SAFETY RULES AND PROHIBITIONS
NAMES OF THE PARTS
No. Description
1
2
Front panel
Air filter
Optional filter (if installed)
3
Terminal block cover
4
Emergency button
5
6
LED Display
Signal receiver
7
Airflow direction flaps
8Deflectors
9
Remote control
10
Note: the above figures are only intended to be a
simple diagram of the appliance and may not
correspond to the appearance of the units that
have been purchased.
No. Description
14 Air outlet grille
Cover
15
gas valve
16
liquid valve
17
11
Indoor unit rating label ( )Stick position optional
18
Outdoor unit rating label
WALL AIR-CONDITIONER
The is made up of two or more units connected
between themselves through copper pipes (properly insulated)
and an electrical connecting cable.
air conditioner
The indoor unit is installed on the walls of the room to be
conditioned.
The outdoor unit is installed on the floor or on the wall on
suitable brackets.
Technical data of the air conditioner are printed on the labels
placed on the indoor and outdoor units.
The remote control has been designed for easy and fast use.
12
Ionizer (if installed) generator
14
16
17
18
INDOOR UNIT
OUTDOOR UNIT
1 2-3
6
4-5
9
11 8
10 7
15
DISPL
AY
HEALTH
Y
3D
ON/OF
F
SWIN
G
FAN
TIMER
SU
PE
R
SLEE
P
MODE
ECO
CLO C
K
12
INDOOR UNIT
OUTDOOR UNIT
10
No. Description
13 Pipe connections (optional)
OUTDOOR UNIT
13
13
4
INDOOR UNIT DISPLAY
The shape and position of switches and indicators may be different according to the model, but their
function is the same.
According to the model, it may only show 2 numbers on the indoor display though there are 3 numbers
on display of the remote controller .(Example: it is on the display of the remote controller but
on the indoor display )
4
2
1
2
5
3
4
1 2 3 4 5
31 2
3
54
No.
Led Function
POWER This symbol appears when the unit is power on
1
2
3
4
5
Temperature display (if present)
/Error code
(1) Lights up during Timer operation when
the air conditioner is operational
(2)Displays the malfunction code when fault
occurs.
SLEEP mode
Lights up during Timer operation.
The symbol appears when the unit is turned
on, and disappear when the unit is turned off.
SLEEP
TIMER
RUN
3
4
2
1245
3
5
Emergency
button
The emergency button is located on the right end
of the unit under the front panel.
front panel
front panel
Open and lift the front panel up to an angle to reach
the emergency button.
Press the emergency button, the unit will operate
COOL mode at first. Press again within 3 seconds,
the unit will change to HEAT mode. Press again after
5 seconds, the unit will turn off.
If the remote controller fails to work or maintenance
necessary, proceed as following:
6
EMERGENCY FUNCTION & AUTO-RESTART FUNCTION
The appliance is preset with an auto-restart function.
In case of a sudden power failure, the module will
memorizes the setting conditions before the power
failure. When the power restores, the unit will restart
automatically with the previous settings preserved
by the memory function.
REMOTE CONTROL ( NOTE: SEE ILLUSTRATION ON PAGE 8 )
ON/OFF
Mode OPTIONS
AUTO
COOL
DRY
FAN
HEAT
AUTO
COOL
DRY
FAN
HEAT
ON
OFF
You will hear a beep when you press the following buttons or select the following optional functions.
(Optional Function: COMFORTABLE COOLING airflow)
(Optional Function: COMFORTABLE HEATING airflow)
HEALTH (Optional Function: generate the ionizer)
(button: SWING LEFT/RIGHT)
(Optional Function: )8 Heating
8 CH (Optional Function: Wide-angle air supply)
O
TIMER DISPLAY HEALTH I FEEL 8 C H
O
TIMER DISPLAY HEALTH SLEEP MILDEW I FEEL 8 C H
O
TIMER DISPLAY HEALTH MILDEW I FEEL 8 C H
O
TIMER DISPLAY HEALTH I FEEL 8 C H
O
TIMER DISPLAY HEALTH SLEEP I FEEL 8 C H
O
CLEAN TIMER DISPLAY HEALTH I FEEL 8 C H
O
CLEAN TIMER DISPLAY HEALTH SLEEP MILDEW I FEEL 8 C H
O
CLEAN TIMER DISPLAY HEALTH MILDEW I FEEL 8 C H
O
CLEAN TIMER DISPLAY HEALTH I FEEL 8 C H
O
CLEAN TIMER DISPLAY HEALTH SLEEP I FEEL 8 C H
To select the mode of operation(AUTO COOL DRY FAN HEAT).
Press this button to activate/deactivate the Super function which enables the
unit to reach the preset temperature in the shortest time.
To decrease temperature, time setting or choose the function.
To increase temperature, time setting or choose the function.
To turn on or off the air conditioner .
To select the fan speed of auto/mute/low/mid-low/mid/mid-high/high/
turbo, cycle as below.
8
10
6
7
9
MODE
TURBO
1
2
3
4
FAN
5
No.
Button Function
OPTION To activate or deactivate optional function(Check below table).
To activate the swing of horizontal flap(up/down) or deactivate it.
To activate the swing of vertical flap(left/right) or deactivate it.
Press this button to activate/deactivate the ECO function .
ECO
Celsius or Fahrenheit degree change: Long press TURBO button of remote controller, for more
than 6 seconds, until the temperature display changes to Celsius or Fahrenheit.
7
Flashing
The shape and position of buttons and indicators may vary according to the model, but their function is
the same.
The display and some functions of the remote control may vary according to the model.
The unit confirms the correct reception of each button with a beep.
REMOTE CONTROL
AUTO COOL DRY
FAN HEAT ECO
SLEEP TIMER I FEEL
HEALTH MILDEW
DISPLAY 8 CH
7
3
1
9*
5
8
4
2*
10*
6
8
CLEAN
REMOTE CONTROL
Remote control DISPLAY
Meaning of symbols on the liquid crystal display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Mode Cooling indicator
Mode Dry indicator
Mode Fan indicator
Mode Heating indicator
Fan speed indicator:
Auto/low/mid-low/mid/mid-high/high
15
SUPER indicator
16
17
Mute indicator
18
Flap swing angle indicator
19
Temperature indicator
Meaning
No. Symbols
Deflector swing angle indicator
Comfortable cooling airflow indicator
I FEELSLEEP
HEALTH
DISPLAY
MILDEW
8 CH
Timer indicator
Single indicator
Child Lock function indicator
Battery indicator
Mode Auto function indicator
TIMER
Comfortable heating airflow indicator
Optional functions indicator
You will hear a beep when you press the following buttons or select the following optional functions.
(Optional Function: COMFORTABLE COOLING airflow)
(Optional Function: COMFORTABLE HEATING airflow)
HEALTH (Optional Function: generate the ionizer)
(button: SWING LEFT/RIGHT)
(Optional Function: )8 Heating
8 CH (Optional Function: Wide-angle air supply)
TIMER
ECO indicator
CLEAN
9
10
Replacement of Batteries
Remove the battery cover plate from the rear of the remote control, by sliding it in the direction of the arrow.
Install the batteries according the direction (+and -)shown on the Remote Control.
Reinstall the battery cover by sliding it into place.
Use 2 LRO 3 AAA (1.5V) batteries. Do not use rechargeable batteries.
Replace the old batteries with new ones of the same type when the display is no longer legible.
Do not dispose batteries as unsorted municipal waste.
Collection of such waste separately for special treatment is necessary.
1. Direct the remote control toward the Air conditioner.
2. Check that there are no objects between the remote control
and the Signal receptor in the indoor unit.
3. Never leave the remote control exposed to the rays of the sun.
4. Keep the remote control at a distance of at least 1m from the
television or other electrical appliances.
Note
Child- lo
ck:
Press an d
Togeth er to act ive
Display ON/OFF
:
Long pre s s ECO b-
utto n.
Please r
emove b
a-
Tterie s to avo i d
le-
akage d
amage w -
Hen not using f o
r
A long t
ime.
Note
Child-lock:Press and
together to active.
Display ON/OFF:
Long press ECO button.
Please remove batteries
to avoid leakage damage
when not using for a long
time.
Signal
receptor
Each time when you insert the batteries for the first 3 minutes, turn off the remote control, then you can
program it for (only cooling) or (cooling and heating) type.
1. Press and hold MODE button over (5seconds) to access the change mode to COOL or HEAT;
2. Press and hold the MODE button, until it swtich to COOL or HEAT;
NOTE: If you adjust the remote control in cooling mode, it will not be possible to activate the heating
function in units with a heating pump . If you need to reset, take out the batteries and install again.
3. Then release the pressing and wait for 5 seconds, the function will be selected.
O O
You also can program the temperature display switch over function between C and F.
1. Press and hold the TURBO button over (5seconds) to get into the change mode;
O O
2. Press and hold the TURBO button, until it switch to C and F;
3. Then release the pressing and wait for 5 seconds, the function will be selected.
REMOTE CONTROL
11
flaps
flap
movement Deflectors
“ ”SWING CONTROL OF THE AIR FLOW
The deflectors are positioned manually and placed un-
der the flaps. They allow to direct the air flow rightw-
ard or leftward.
Never position Flaps manually, the delicate mech-
anism might seriously damaged!
Never poke fingers, sticks or other objects in the air
inlet or outlet vents. Such accidental contact with live
parts might cause unforeseeable damage or injury.
This adjustment must be done while the appliance
is switched off.
1.Press the button to activate the FLAP ,
(1) If press time interval is within 2 seconds, the swing will cycle
as below:
(2) If press time is longer, the swing angle range of horizontal
flap will cycle as below:
(3) If press time interval is over 2 seconds, it will be deactivate
the air flow is directed alternatively from up to down, to
guarantee an even distribution of the air in the room.
2.Press the button to activate the motorized deflectors ,
(1) If press time interval is within 2 seconds, the swing will cycle
as below:
(2) If press time is longer, the swing will cycle as below:
(3) If press time interval is over 2 seconds, it will deactivate
the air flow is directed alternatively from left to right.
(Optional function, depends on the model)
OPERATING INSTRUCTIONS
Filter
Heat
Fan
Exchanger
The direction of the air outlet is motorized up and down
by flaps, and manually moved right and left by the vertical
deflectors, for some models, the vertical deflectors could be
controlled by motor as well.
The air sucked by the fan enters from the grill and
passes through the filter, then it is cooled/dehumidified
or heated through the heat exchanger.
deactivate
deactivate
12
OPERATING INSTRUCTIONS
COOLING MODE
The cooling function allows the air condit-
ioner to cool the room and at the same time
reduces Air humidity.
COOL
To activate the cooling function ( COOL ) , press the
MODE button until the symbol COOL
appears on the display.
HEATING MODE
The cooling function is activated by setting the button
or at a temperature lower than that of the room.
To optimize the function of the Air conditioner, adjust
the temperature (1) , the speed (2) and the direction
of the air flow (3) by pressing the button indicated.
HEAT
The heating function allows the air conditi-
oner to heat the room.
To activate the heating function ( HEAT ) , press the
MODE button until the symbol HEAT
appears on the display.
With the button or set a temperature higher than
that of the room.
To optimize the function of the Air conditioner adjust
the temperature ( 1 ), the speed ( 2 ) and the direction
of the air flow ( 3 ) by pressing the button indicated.
In HEATING operation, the appliance can automatically
activate a defrost cycle, which is essential to clean the
frost on the condenser so as to recover its heat exchange
function. This procedure usually lasts for 2-10 minutes
during defrosting, indoor unit fan stop operation.
After defrosting, it resumes to HEATING mode
automatically.
This function reduces the humidity of the
air to make the room more comfortable.
To set the DRY mode , Press MODE until
DRY appears in the display. An automatic
function of alternating cooling cycles and air
fan is activated.
DRY
DRY MODE
13
OPERATING INSTRUCTIONS
FAN Fan mode ventilation only.
To set the FAN mode, Press MODE until
FAN appears on the display.
FAN MODE(Not FAN button)
To optimize the function of the air conditioner, adjust
the temperature(1), the speed (2) and the direction of the
air flow (3) by pressing the buttons indicated.
AUTO MODE
Automatic mode.
To activate the AUTO mode of operation,
press the MODE button on the remote control until
the symbol AUTO appears on the display.
In AUTO mode the run mode will be set automatically
according to the room temperature.
To optimize the function of the air conditioner, adjust
the temperature(1), the speed (2) and the direction of the
air flow (3) by pressing the buttons indicated.
AUTO
DISPLAY function (Indoor display)
DISPLAY Switch ON/OFF the LED display on panel
SLEEP
SLEEP function
Press OPTION button , select the DISPLAY by
pressing the button or until symbol DISPLAY is flashing;
Press OPTION again to switch off the LED display on the
panel, and appears on the remote control display.
Do it again to switch on the LED display.
DISPLAY
After 10 hours running in sleep mode, the air conditioner
will change to the previous setting mode.
Press OPTION button, select the SLEEP by
pressing the button or until symbol SLEEP is flashing;
Press OPTION again to activate the SLEEP function,
and SLEEP appears on the display.
Do it again to deactivate this function.
14
OPERATING INSTRUCTIONS
ECO function
Turbo function
To activate turbo function, press the TURBO button
or press the FAN button until symbol appears
on the display.
In AUTO/HEAT/COOL/FAN mode, when you select
TURBO feature, it will use the highest fan setting to
blow strong airflow.
To cancel this function, press the FAN to switch
other fan speed or press the TURBO button again.
ECO
In this mode the appliance automatically sets the operation
to achieve energy savings.
1. Press the "ON / OFF" button to turn on appliance and
select a COOLING / HEATING mode.
2. Press the "ECO" button, the appliance will run in ECO
mode.
3. Pressing the "ECO" button again will cancel the mode,
"ECO" will no longer be shown on the LCD screen.
NOTE:
The ECO function is available in COOLING and HEATING
modes.
15
OPERATING INSTRUCTIONS
HEAT
SLEEP TIMER I FEEL
DISPLAY 8 CH
HEAT
TIMER
CLEAN DISPLAY
Figure1,Timer-on
when switch off
Figure2,Timer-off
when switch on
TIMER To set the automatic timer switch-on /off
of the air conditioner
Note:
All programming should be operated within 5 seconds,
otherwise the setting will be cancelled.
1. Press OPTION button, select the Timer by
pressing the button or until symbol TIMER
is flashing;
Timer setting/change/cancel:
3. To set the timer or change the timer:
(1)Press the button or to set the expected timer
(Increase or decrease at half-hour intervals)
the symbols and TIMER both are flashing.h
(2) Press OPTION or wait for 5 seconds without any
operation to confirm the timer, the pre-setting
timer like and symbol TIMER will be on the
display.
4. To cancel the timer(if TIMER is on).
Repeat step 1, step 2, then press OPTION or wait for 5
seconds without any operation to cancel the timer.
A sample for the Timer-on as Figure1, Timer-off as Figure2
I FEEL function (Optional)
I FEEL
Press OPTION button, select the I FEEL by
pressing the button or until symbol I FEEL
is flashing; Press OPTION again to activate the
I FEEL function, and will appear on the display.
Do it again to deactivate this function.
I FEEL
This function enables the remote control to measure
the temperature at its current location, and send this
signal to the air conditioner to optimize the temperature
around you and ensure the comfort.
It will automatically deactivate 2 hours later.
2. Press OPTION again, the data symbol like
and TIMER will be flashing;
TIMER function
16
OPERATING INSTRUCTIONS
MILDEW function (Optional)
1. This function helps carry away the accumulated
dirt, bacteria, etc from the evaporator.
2. This function will run about 30 minutes, and it will return to the
pre-setting mode .You can press to cancel this function during
the process. You will hear 2 beeps when it's finished or cancelled.
3. It's normal if there is some noise during this function process,
as plastic materials expand with heat and contract with cold.
4. We suggest operating this function at the following ambient
conditions to avoid certain safety protection features.
5. It's suggested to utilize this function every 3 months.
SELF-CLEAN function (Optional)
Indoor unit
Outdoor unit
Temp< 86 (30 )
41 (5 )<Temp<86 (30 )
MILDEW
Press OPTION button , select the MILDEW by
pressing the button or until symbol MILDEW
is flashing; Press OPTION again to activate the
MILDEW function, MILDEW will appear on the display.
Do it again to deactivate this function.
After running COOL/DRY for more than 30 minutes,
you can operate this function, the unit will blow airflow
for about 15 minutes to dry the inner parts to avoid mildew,
then shuts off the unit.
Note: MILDEW function only available in DRY/COOLING mode.
Press OPTION button , select CLEAN by pressing the
button or until symbol CLEAN is flashing; Press OPTION again
to activate the CLEAN function, and appears on the display.
Do it again to deactivate this function.
CLEAN
CLEAN
8 heating function (Optional)
8 H
1.Press OPTION at the first time, select the 8 H by
pressing the button or until symbol 8 H
is flashing; Press OPTION again to choose the
8 heating function, and 8 H appears on the display.
Do it again or change the mode to deactivate this function.
2.If the unit is standby, this function will automatically start
heating mode when the indoor temperature is equal or lower
than 8 (46 ), it will return standby if the temperature is
equal or higher than 18 (64 ).
It can be set in Cool/Heat/Dry/Fan/Auto mode,
but you need to turn off the unit to activate it.
Switch off the air conditioner at first.
PROTECTION
The protective device may trip and stop the appliance in the cases listed below.
For T1 Climate condition models:
After stopping and restarting the air coditioner or after changing the mode during operation, the
system does not restart immediately, Until after 3 minutes(protection function for the compressor).
Outdoor air temperature is over 86 (30 )
2
Room temperature is over 86 (30 )
Outdoor air temperature is below -13 (-25 )
1Heating
Cooling
Outdoor air temperature is over 122 (50 )
Outdoor air temperature is below 5 (-15 )
No.
MODEL
17
18
INSTALLATION---Selecting the Installation Place
Install the indoor unit level on a strong wall that is not
subject to vibrations.
The inlet and outlet ports should not be obstructed: the
air should be able to blow all over the room.
Do not install the unit near a source of heat, steam, or
flammable gas.
Install the unit near an electric socket or private circuit.
Do not install the unit where it will be exposed to
direct sunlight.
Install the unit where connection between indoor and
outdoor unit is as easy as possible.
Install the unit where it is easy to drain the condensed
water.
Check the machine operation regularly and leave the
necessary space (as shown in the picture).
Install the indoor unit where the filter can be easily
accessible.
condensed water drain pipe
6
Sleeve
insulating covering
electrical cable
Mounting plate
Do not install the outdoor unit near sources of heat,
steam or flammable gas.
Do not install the unit in too windy or dusty places.
Do not install the unit where people often pass.Select
a place where the air discharge and operating sound
level will not disturb neighbours.
Avoid installing the unit where it will be exposed
to direct sunlight ( other wise use a protection , if
necessary, that should not interfere with the air flow).
Leave space as shown in the picture for the air to
circulate freely.
Install the outdoor unit in a safe and solid place.
If the outdoor unit is subject to vibration, place rubber
gaskets onto the feet of the unit.
water drain pipe
Minimum space to be left showing in the
picture
Outdoor unit
Indoor unit
Pipe length is
50' Max
be less than 5m
Height should
Outdoor unit
Indoor unit
Pipe length is
50' Max
be less than 5m
Height should
Installation Diagram
INDOOR UNIT
OUTDOOR UNIT
Only persons and/or companies qualified and experienced in the installation, service and repair of refrigerant
products should be permitted to do so. The purchaser must ensure that the person and/or company who is to
install, service or repair this air conditioner has qualifications and experience in refrigerant products.
6
6
20
20
12
12
79

Produkt Specifikationer

Mærke: Daizuki
Kategori: Aircondition
Model: DXTH36X426-17

Har du brug for hjælp?

Hvis du har brug for hjælp til Daizuki DXTH36X426-17 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Aircondition Daizuki Manualer

Daizuki

Daizuki DXCC09E426-20 Manual

10 Januar 2025
Daizuki

Daizuki DXTH18X426A-23 Manual

27 December 2024
Daizuki

Daizuki AHC60H14 Manual

27 December 2024
Daizuki

Daizuki AHC48H14 Manual

27 December 2024
Daizuki

Daizuki AHC42H14 Manual

27 December 2024
Daizuki

Daizuki DXP-12HP2632 Manual

5 September 2024
Daizuki

Daizuki DXP-09HP2632 Manual

5 September 2024
Daizuki

Daizuki DXAH18E426-21 Manual

5 September 2024
Daizuki

Daizuki DXP-15HP2632 Manual

5 September 2024
Daizuki

Daizuki CVX1860-140BYS Manual

2 September 2024

Aircondition Manualer

Nyeste Aircondition Manualer

ARCTIC WIND

ARCTIC WIND 3AWH12000A Manual

4 Marts 2025
Daitsu

Daitsu AUD-30K-DB Manual

28 Februar 2025
Daitsu

Daitsu AUD 36K DB Manual

28 Februar 2025
Daitsu

Daitsu AUD 48K DB Manual

28 Februar 2025
Daitsu

Daitsu AUD 60TK DB Manual

28 Februar 2025
Daitsu

Daitsu AUD 42K DB Manual

28 Februar 2025
Daitsu

Daitsu AUD 48TK DB Manual

28 Februar 2025
Daitsu

Daitsu AUD 36TK DB Manual

28 Februar 2025
Daitsu

Daitsu AUD 18K DB Manual

28 Februar 2025
Daitsu

Daitsu AUD 24K DB Manual

28 Februar 2025