Danfoss TP5000 Si Manual

Danfoss Termostat TP5000 Si

Læs nedenfor 📖 manual på dansk for Danfoss TP5000 Si (2 sider) i kategorien Termostat. Denne guide var nyttig for 15 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
Fig.1
TP5000 Si/TP5000 RF Si
User Instructions
Mon-Fri Sat-Sun
Fig.2
Before programming the thermostat press and release the RESET button to restart
the unit. (Fig. 1)
Setting the Clock and Day
The day and time are set in the factory and therefore it will not normally be necessary
to do this on site. Changes between summer and winter time are handled automatically
by the unit.
Accepting the Factory Pre-settings
The TP5000 Si has pre-set times already programmed in, which often suit most people
(see table below).
Note: If set up for 4 events per day, events 3 & 4 are skipped. If set up for 2 events per
day, events 2, 3, 4 & 5 are skipped and the events are re-numbered.
To adjust the factory pre-settings & set your own time and temperature
programmes
For Days 1-5 (weekdays)
a) Press PROG (Fig. 2) until the 1st pre-set time and temperature (Event 1 Days 1,2,3,4,5)
(Fig. 3).
b) Use + or – buttons (Fig. 4) to adjust the TIME (press and hold to change in 10 min
increments).
c) Use Λ or V buttons (Fig. 5) to adjust the TEMPERATURE.
d) Press PROG (Fig. 2) to move to next preset time & temp (Event 2) (Fig. 6).
e) Repeat steps b, c & d for programming Events 3, 4, 5 & 6.
For Days 6-7 (weekends)
Press •PROG (Fig. 2) to show 1st pre-set time and temperature (Event 1 Days 6-7)
(Fig. 7).
Repeat steps b, c and d above to programme time and temperature events for •
the weekend.
Returning to RUN mode
Press PROG (Fig. 2) – the colon in the LCD display will start to flash (Fig. 8).
Fig.5
Fig.4
Fig.6
Fig.7
Fig.8
Event Time Temp. °C
1 06:30 20
2 08:30 15
3 11:30 20
4 13:30 15
5 16:30 21
6 22:30 15
Event Time Temp. °C
1 07:30 20
2 09:30 20
3 11:30 20
4 13:30 20
5 16:30 20
6 22:30 15
RESET
Fig.3
Complete Shut off - Summer time
Press Λ and V together to enter thermostat mode. A frost protection symbol (snowflake in a
shield) will appear in the display . Press the down arrow ∨ once, OFF will appear in the display.
To return to automatic programming press both ∧ and ∨ together.

Produkt Specifikationer

Mærke: Danfoss
Kategori: Termostat
Model: TP5000 Si

Har du brug for hjælp?

Hvis du har brug for hjælp til Danfoss TP5000 Si stil et spørgsmål nedenfor, og andre brugere vil svare dig


Termostat Danfoss Manualer

Danfoss

Danfoss RA 2982 Manual

6 Oktober 2024
Danfoss

Danfoss TP5E-RF Manual

23 September 2024
Danfoss

Danfoss TP5 Manual

17 September 2024
Danfoss

Danfoss Ally - Radiator Thermostat Thermostaat Manual

1 September 2024
Danfoss

Danfoss TP5001Range gebruik Manual

25 August 2024
Danfoss

Danfoss RA 2000 series Manual

23 August 2024
Danfoss

Danfoss TP5000 plus RF Manual

19 August 2024
Danfoss

Danfoss RET 230 HCW-3 installatie Manual

17 August 2024
Danfoss

Danfoss TP9000 Si Manual

17 August 2024
Danfoss

Danfoss TP5000 Si Manual

16 August 2024

Termostat Manualer

Nyeste Termostat Manualer

EQ-3

EQ-3 CC-RT-O-CnL-W-R5-2 Manual

16 December 2024
EQ-3

EQ-3 HmIP-WTH-2 Manual

16 December 2024
EQ-3

EQ-3 HMIP-WTH Manual

16 December 2024
EQ-3

EQ-3 HMIP-eTRV Manual

16 December 2024
EQ-3

EQ-3 HM-TC-IT-WM-W-EU Manual

16 December 2024
EQ-3

EQ-3 HM-CC-RT-DN Manual

16 December 2024
EQ-3

EQ-3 HMIP-BWTH Manual

16 December 2024
EQ-3

EQ-3 HMIP-BWTH24 Manual

16 December 2024
EQ-3

EQ-3 131651A0 Manual

16 December 2024
EQ-3

EQ-3 HmIP-eTRV-B Manual

16 December 2024