DeWalt DC720 Manual

DeWalt Boremaskine DC720

Læs nedenfor 📖 manual på dansk for DeWalt DC720 (7 sider) i kategorien Boremaskine. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/7

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 Joppa Road, Towson, MD 21286

(MAY14) Part No. N400408 DC720, DC725, DC730, DC742, DCD760, DCD775

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme;

the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the

array of lozenge-shaped humps on the surface of the tool.

DC725, DCD775 Cordless Compact 1/2" (13 mm) Drill/Driver/Hammerdrill

DC720, DC730 , DCD760 Cordless Compact 1/2" (13 mm) Drill/Driver

DC742 Cordless Compact 3/8" (10 mm) Drill/Driver

DC725, DCD775 Marteau perforateur/perceuse/visseuse compact sans fil de 13mm (1/2") / DC720, DC730 Perceuse/visseuse

compact sans fil de 13mm (1/2") / DC742 Perceuse/visseuse compact sans fil de 10mm (3/8")

DC725, DCD775 Taladro/destornillado/Percutor Inalámbrico Compacto de 13mm (1/2") / DC720, DC730 Taladro/destornillado

Inalámbrico Compacto de 13mm (1/2") / DC742 Taladro/destornillado Inalámbrico Compacato de 10mm (3/8")

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D WALT • www.dewalt.comE

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

NOTICE: may Indicates a practice which, if not avoided, not related to personal injury

result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL

US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) The Do not force the power tool. Use the correct power tool for your application.

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result

in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the manufacturer. A charger that is

suitable for one type of battery pack may create a risk of fire when used with another battery

pack.

b) Use power tools only with specifically designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects, like paper

clips, coins, keys, nails, screws, or other small metal objects, that can make a

connection from one terminal to another. Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Drill/Driver/Hammerdrill Safety Warnings

• Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.

• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping surfaces, when performing an operation where

the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power tool “live” and could give the operator an

electric shock.

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

• Wear safety goggles or other eye protection. Hammering and drilling operations cause

chips to fly. Flying particles can cause permanent eye damage.

• Hammer bits and tools get hot during operation. Wear gloves when touching them.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long

hair can be caught in moving parts.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable surface where it will not

cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the

battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The symbols and their definitions are

as follows:

V .....................volts A .........................amperes

Hz ...................hertz W ........................watts

min .................minutes or AC .............alternating current

or DC .....direct current or AC/DC......alternating or direct current

...................Class I Construction no .......................no load speed

....

...........

...

.........

...

.........

...

.........

...

.........

...

........

......

....(grounded) n .........................rated speed

...................Class II Construction .......................earthing terminal

(double insulated) ........................safety alert symbol

…/min ............per minute BPM ...................beats per minute

IPM .................impacts per minute RPM ...................revolutions per minute

SPM ...............strokes per minute sfpm ...................surface feet per minute

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include catalog number and voltage. Consult

the chart at the end of this manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using the battery pack and charger,

read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting or removing the battery from the charger may

ignite the dust or fumes.

• NEVER force battery pack into charger. DO NOT modify battery pack in any way to fit

into a non-compatible charger as battery pack may rupture causing serious personal

injury. Consult the chart at the end of this manual for compatibility of batteries and chargers.

• Charge the battery packs only in DEWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the temperature may

reach or exceed 105 °F (40 °C) (such as outside sheds or metal buildings in summer).

DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason. If

battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped,

run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Electric

shock or electrocution may result. Damaged battery packs should be returned to service center

for recycling.

NOTE: Battery storage and carrying caps are provided for use whenever the battery

is out of the tool or charger. Remove cap before placing battery in charger or tool.

WARNING: Fire hazard. Do not store or carry battery so that metal objects

can contact exposed battery terminals. For example, do not place battery in

aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails,

screws, keys, etc. without battery cap. Transporting batteries can possibly

cause fires if the battery terminals inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the like. The U.S. Department of Transportation

Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on

airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected

from short circuits. So when transporting individual batteries, make sure that the battery terminals

are protected and well insulated from materials that could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR NICKEL CADMIUM (NiCd) OR NICKEL METAL

HYDRIDE (NiMH)

• Do not incinerate the battery pack even if it is severely damaged or is completely worn

out. The battery pack can explode in a fire.

• A small leakage of liquid from the battery pack cells may occur under extreme usage

or temperature conditions. This does not indicate a failure.

However, if the outer seal is broken:

a. and the battery liquid gets on your skin, immediately wash with soap and water for several

minutes.

b. and the battery liquid gets into your eyes, flush them with clean water for a minimum of

10 minutes and seek immediate medical attention. ( The liquid is 25–35% Medical note:

solution of potassium hydroxide.)

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely damaged or is completely

worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin, immediately wash area with mild

soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes

or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a

mixture of liquid organic carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If

symptoms persist, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

The RBRCTM Seal

The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the nickel

cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate that

the costs to recycle these batteries (or battery packs) at the end of their useful life

have already been paid by DEWALT. In some areas, it is illegal to place spent nickel

cadmium, nickel metal hydride or lithium ion batteries in the trash or municipal solid

waste stream and the RBRC program provides an environmentally conscious

alternative.

RBRC™ in cooperation with DEWALT and other battery users, has established programs in the

United States and Canada to facilitate the collection of spent nickel cadmium, nickel metal hydride

or lithium ion batteries. Help protect our environment and conserve natural resources by returning

the spent nickel cadmium, nickel metal hydride or lithium ion batteries to an authorized DEWALT

service center or to your local retailer for recycling. You may also contact your local recycling center

for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.

Important Safety Instructions for All Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions

for battery chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery pack,

and product using battery pack.

DANGER: Electrocution hazard. 120 volts are present at charging terminals. Do not probe with

conductive objects. Electric shock or electrocution may result.

WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only D WALT rechargeable batteries. E

Other types of batteries may burst causing personal injury and damage.

NOTICE: Under certain conditions, with the charger plugged in to the power supply, the exposed

charging contacts inside the charger can be shorted by foreign material. Foreign materials of a

conductive nature such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil,

or any buildup of metallic particles should be kept away from charger cavities. Always unplug the

charger from the power supply when there is no battery pack in the cavity. Unplug charger before

attempting to clean.

• DO NOT attempt to charge the battery pack with any chargers other than the ones in

this manual. The charger and battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than charging DEWALT

rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage

to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper extension

cord could result in risk of fire, electric shock, or electrocution.

• When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using more than one extension to make up

the total length, be sure each individual extension contains at least the minimum wire size. The

following table shows the correct size to use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the

cord.

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Boremaskine
Model:	DC720

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DC720 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Boremaskine DeWalt Manualer

26 August 2024

15 Juli 2024

10 Juni 2024

29 Maj 2024

19 Maj 2024

9 Maj 2024

5 Maj 2024

8 Februar 2024

DeWalt D25404K Manual

29 Januar 2024

DeWalt DW194 Manual

23 December 2023

Boremaskine Manualer

Nyeste Boremaskine Manualer

Einhell BT-DH 1600 Manual

23 November 2024

Einhell BT-RH 920 Manual

23 November 2024

Einhell RT-RH 24 Manual

23 November 2024

Einhell BT-RH 1600 Manual

22 November 2024

Einhell BT-RH 850 Manual

22 November 2024

Einhell BT-RH 900 Manual

22 November 2024

Alpha Tools A-ID 550 E Manual

18 November 2024

Festo DGSC-6-10-P-P Manual

17 November 2024

Black Decker KR506 Manual

14 November 2024

Makita HR4002 Manual

14 November 2024