DeWalt DW057K-2 Manual

DeWalt Skruemaskine DW057K-2

Læs nedenfor 📖 manual på dansk for DeWalt DW057K-2 (7 sider) i kategorien Skruemaskine. Denne guide var nyttig for 36 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/7

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

DW050, DW052, DW054, DW056 Cordless Impact Driver • DW051 3/8" Cordless Impact Wrench

DW053, DW055, DW057, DW059 1/2" Cordless Impact Wrench

DW050, DW052, DW054, DW056 Gestionnaire Sans fil De l'Impact • Clé D'Impact Sans fil de DW051 3/8 po

Clé D'Impact Sans fil de DW053, DW055, DW057, DW059 1/2 po

DW050, DW052, DW054, DW056 Destornillador de impacto inalámbrico • DW051 Llave de impacto inalámbrica de

9,5 mm (3/8")

DW053, DW055, DW057, DW059 Llave de impacto inalámbrica de 12,7 mm (1/2")

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (JUL06)

The following are trademarks for one or more DEWALT power tools: the yellow and black color

scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box con-

figuration; and the array of lozenge-shaped humps on the surface of the tool.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Rules – For All Battery Operated Tools

WARNING! Read and understand all instructions. Failure to follow

all instructions listed below may result in electric shock, fire and/or

serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

•Keep your work area clean and well lit. Cluttered benches and dark areas invite acci-

dents.

•Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust

or fumes.

•Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

•Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from

heat, oil, sharp edges or moving parts. Replace damaged cords immediately.

Damaged cords may create a fire.

•A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery. A charger that may be suit-

able for one type of battery may create a risk of fire when used with another battery.

•Use battery operated tool only with the specifically designed battery pack. Use of any

other batteries may create a risk of fire.

PERSONAL SAFETY

•Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in serious per-

sonal injury,

•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair

can be caught in moving parts. Air vents often cover moving parts and should also be

avoided.

•Avoid accidental starting. Be sure switch is in the locked or off position before

inserting battery pack. Carrying tools with your finger on the switch or inserting the bat-

tery pack into a tool with the switch on invites accidents.

•Remove adjusting keys or wrenches before turning the tool on. A wrench or key that

is left attached to a rotating part of the tool may result in personal injury.

•Do not overreach. Keep proper footing and balance at all times. Proper footing and bal-

ance enables better control of the tool in unexpected situations.

•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

•Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to a loss

of control.

•Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer and the rate for which it is designed.

•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

•Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tool. Such pre-

ventative safety measures reduce the risk of starting the tool accidentally.

•Store idle tools out of reach of children and other untrained persons. Tools are dan-

gerous in the hands of untrained users.

•When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a con-

nection from one terminal to another. Shorting the battery terminals together may cause

sparks, burns, or a fire.

•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

•Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

•Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

•Tool service must be performed only by qualified repair personnel. Service or main-

tenance performed by unqualified personnel could result in a risk of injury.

•When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of electric shock or injury.

Additional Specific Safety Rules

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

•Wear safety goggles or other eye protection. Hammering and drilling operations cause

chips to fly. Flying particles can cause permanent eye damage.

•Bits, sockets and tools get hot during operation. Wear gloves when touching them.

•Do not operate this tool for long periods of time. Vibration caused by tool action may

be harmful to your hands and arms. Use gloves to provide extra cushion and limit expo-

sure by taking frequent rest periods.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious

and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory pro-

tection appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: When not in use, place tool on its side on a stable surface where it will not

cause a tripping or falling hazard. Some tools with large battery packs will stand upright on

the battery pack but may be easily knocked over.

CAUTION: Wear appropriate personal hearing protection during use. Under some con-

ditions and duration of use, noise from this product may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V ..................volts A......................amperes

Hz................hertz W ....................watts

min ..............minutes ..................alternating current

............direct current no ....................no load speed

................Class I Construction ....................earthing terminal

....................(grounded) ....................safety alert symbol

..................Class II Construction …/min..............revolutions or reciprocation

.................... ........................(double insulated) per minute

BPM ............beats per minute

Important Safety Instructions for Battery Packs

When ordering replacement battery packs, be sure to include catalog number and voltage.

Extended Run-Time battery packs deliver more run-time than standard battery packs.

Consult the chart at the end of this manual for compatibility of chargers and battery packs.

NOTE: Your tool will accept either standard or Extended Run Time battery packs. However,

be sure to select proper voltage. Batteries slowly lose their charge when they are not on the

charger, the best place to keep your battery is on the charger at all times.

The battery pack is not fully charged out of the carton. Before using the battery pack and

charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

•Do not incinerate the battery pack even if it is severely damaged or is completely

worn out. The battery pack can explode in a fire.

•A small leakage of liquid from the battery pack cells may occur under extreme usage

or temperature conditions. This does not indicate a failure. However, if the outer seal is

broken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If battery liquid gets into your eyes, flush them with clean water for a minimum of 10 min-

utes and seek immediate medical attention. (Medical note: The liquid is 25-35% solution

of potassium hydroxide.)

•Do not carry extra battery packs in aprons, pockets, or tool boxes along with other

metal objects. Battery pack could be short circuited causing damage to the battery pack

and possibly causing severe burns or fire.

• Charge the battery packs only in DEWALT chargers.

•DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the

temperature may reach or exceed 105°F (such as outside sheds or metal

buildings in summer).

DANGER: Electrocution hazard. Never attempt to open the battery pack for any

reason. If battery pack case is cracked or damaged, do not insert into charger.

Electric shock or electrocution may result. Damaged battery packs should be

returned to service center for recycling.

NOTE: Battery storage and carrying caps are provided for use whenever the battery is out of

the tool or charger. Remove cap before placing battery in charger or tool.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can con-

tact exposed battery terminals. For example, do not place battery in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc. without battery cap.

Transporting batteries can possibly cause fires if the battery terminals inadvertently

come in contact with conductive materials such as keys, coins, hand tools and the like.

The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on lug-

gage) UNLESS they are properly protected from short circuits. So when transporting individ-

ual batteries, make sure that the battery terminals are protected and well insulated from mate-

rials that could contact them and cause a short circuit.

CAUTION: Battery pack must be securely attached to tool. If battery pack is detached, per-

sonal injury may result.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel

cadmium and nickel metal hydride batteries (or battery packs) indicate that the

costs to recycle these batteries (or battery packs) at the end of their useful life

have already been paid by DEWALT. In some areas, it is illegal to place spent

nickel cadmium and nickel metal hydride batteries in the trash or municipal solid

waste stream and the RBRC program provides an environmentally conscious alternative.

RBRC™ in cooperation with DEWALT and other battery users, has established programs in

the United States and Canada to facilitate the collection of spent nickel cadmium and nickel

metal hydride batteries. Help protect our environment and conserve natural resources by

returning the spent nickel cadmium and nickel metal hydride batteries to an authorized

DEWALT service center or to your local retailer for recycling. You may also contact your local

recycling cen tion on where to drop off the spent battery.ter for informa

RBRC™ is a registered trademark of the

Rechargeable Battery Recycling Corporation.

Important Safety Instructions for Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for battery

chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery

pack, and product using battery pack.

DANGER: Electrocution hazard. 120 volts are present at charging terminals. Do not probe

with conductive objects.

WARNING: Shock hazard. Do not allow any liquid to get inside charger.

CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable

batteries. Other types of batteries may burst causing personal injury and damage.

CAUTION: Under certain conditions, with the charger plugged in to the power supply, the

exposed charging contacts inside the charger can be shorted by foreign material. Foreign mate-

rials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup

of metallic particles should be kept away from charger cavities. Always unplug the charger from

the power supply when there is no battery pack in the cavity. Unplug charger before attempting

to clean.

•DO NOT attempt to charge the battery pack with any chargers other than the ones in

this manual. The charger and battery pack are specifically designed to work together.

•These chargers are not intended for any uses other than charging D EWALT recharge-

able batteries. Any other uses may result in risk of fire, electric shock or electrocution.

•Do not expose charger to rain or snow.

•Pull by plug rather than cord when disconnecting charger. This will reduce risk of

damage to electric plug and cord.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Skruemaskine
Model:	DW057K-2

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DW057K-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skruemaskine DeWalt Manualer

DeWalt DW130VK Manual

3 Oktober 2024

14 September 2024

6 September 2024

4 September 2024

3 September 2024

3 September 2024

3 September 2024

30 August 2024

30 August 2024

30 August 2024

Skruemaskine Manualer

Nyeste Skruemaskine Manualer

RYOBI One+ RIW18C Manual

16 November 2024

Hazet 9012MT Manual

14 November 2024

Fischer FSS 18V 400 BL Manual

13 November 2024

Milwaukee M12 BPD Manual

24 Oktober 2024

Milwaukee 2769-20 Manual

7 Oktober 2024

Makita 6906J Manual

4 Oktober 2024

Bosch GSB 18V-65 Professional Manual

4 Oktober 2024

Makita DTW300Z Manual

3 Oktober 2024

Bosch GDX 18V-285 Professional Manual

3 Oktober 2024

Makita DTW180RTJ Manual

2 Oktober 2024